| View previous topic :: View next topic |
| Author |
Message |
stefanpropehan
n00b
Joined: 17 Jun 2004
Posts: 15
Location: Germany - Berlin
|
 Posted: Thu Jun 24, 2004 7:23 am Post subject: xorg ati-radeon Performance |
 |
|
HiDiHo,
habe gestern mal ein wenig an meien Einstellungen für xorg und den mitgelieferten Radeon Treiber gespielt. Leider kann ich die ati Treiber nicht nutzen da ich ein 64 bit System betreibe und ATI noch keine Treiber bereitstellt.
folgende Situation:
| Code: | root@schlapptop stefan # lspci | grep ATI
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
root@schlapptop stefan # less /var/log/Xorg.0.log | grep RADEON
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
(II) RADEON(0): MMIO registers at 0xd0100000
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) RADEON(0): PCI bus 1 card 0 func 0
(==) RADEON(0): Depth 16, (==) framebuffer bpp 16
(II) RADEON(0): Pixel depth = 16 bits stored in 2 bytes (16 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(**) RADEON(0): Option "AGPMode" "4"
(**) RADEON(0): Option "AGPFastWrite" "true"
(**) RADEON(0): Option "EnableDepthMoves" "true"
(**) RADEON(0): Option "EnablePageFlip" "true"
(==) RADEON(0): RGB weight 565
(II) RADEON(0): Using 6 bits per RGB (8 bit DAC)
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(--) RADEON(0): Chipset: "ATI Radeon Mobility 9600 (M10) NP (AGP)" (ChipID = 0x4e50)
(--) RADEON(0): Linear framebuffer at 0xd8000000
(--) RADEON(0): VideoRAM: 131072 kByte (128 bit DDR SDRAM)
(II) RADEON(0): AGP card detected
(II) RADEON(0): I2C bus "DDC" initialized.
(II) RADEON(0): DDC Type: 2, Detected Type: 0
(II) RADEON(0): DDC Type: 4, Detected Type: 0
(II) RADEON(0): Non-DDC laptop panel detected
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 3, Detected Type: 0
(II) RADEON(0): DDC Type: 4, Detected Type: 0
(II) RADEON(0): Displays Detected: Monitor1--Type 2, Monitor2--Type 0
(II) RADEON(0):
(II) RADEON(0): Primary Display == Type 2
(II) RADEON(0): Panel ID string: CPT
(II) RADEON(0): Panel Size from BIOS: 1280x800
(II) RADEON(0): BIOS provided dividers will be used.
(==) RADEON(0): Using gamma correction (1.0, 1.0, 1.0)
(II) RADEON(0): Validating modes on Primary head ---------
(II) RADEON(0): Total number of valid DDC mode(s) found: 0
(II) RADEON(0): No valid mode specified, force to native mdoe
(II) RADEON(0): Total number of valid FP mode(s) found: 1
(--) RADEON(0): Virtual size is 1280x800 (pitch 1280)
(**) RADEON(0): *Mode "1280x800": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "1280x800" 71.00 1280 1312 1344 1456 800 801 804 820
(**) RADEON(0): Default mode "640x350": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "640x350" 71.00 640 1312 1344 1456 350 801 804 820
(**) RADEON(0): Default mode "640x400": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "640x400" 71.00 640 1312 1344 1456 400 801 804 820
(**) RADEON(0): Default mode "720x400": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "720x400" 71.00 720 1312 1344 1456 400 801 804 820
(**) RADEON(0): Default mode "640x480": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "640x480" 71.00 640 1312 1344 1456 480 801 804 820
(**) RADEON(0): Default mode "800x600": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "800x600" 71.00 800 1312 1344 1456 600 801 804 820
(**) RADEON(0): Default mode "1024x768": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "1024x768" 71.00 1024 1312 1344 1456 768 801 804 820
(**) RADEON(0): Default mode "832x624": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "832x624" 71.00 832 1312 1344 1456 624 801 804 820
(**) RADEON(0): Default mode "1152x768": 71.0 MHz (scaled from 0.0 MHz), 48.8 kHz, 59.5 Hz
(II) RADEON(0): Modeline "1152x768" 71.00 1152 1312 1344 1456 768 801 804 820
(==) RADEON(0): DPI set to (75, 75)
(**) RADEON(0): Using AGP 4x mode
(**) RADEON(0): Enabling AGP Fast Write
(**) RADEON(0): Enabling depth moves
(II) RADEON(0): Page flipping enabled
(!!) RADEON(0): For information on using the multimedia capabilities
(WW) RADEON(0): Failed to set up write-combining range (0xd8000000,0x8000000)
(WW) RADEON(0): Direct rendering not yet supported on Radeon 9500/9700 and newer cards
(II) RADEON(0): Memory manager initialized to (0,0) (1280,8191)
(II) RADEON(0): Reserved area from (0,800) to (1280,802)
(II) RADEON(0): Largest offscreen area available: 1280 x 7389
(II) RADEON(0): Using XFree86 Acceleration Architecture (XAA)
(II) RADEON(0): Acceleration enabled
(==) RADEON(0): Backing store disabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Using hardware cursor (scanline 802)
(II) RADEON(0): Largest offscreen area available: 1280 x 7382
(II) RADEON(0): Direct rendering disabled |
und noch die relevanten Einstellungen aus der xorg.conf
| Code: | Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "RV350 [Mobility Radeon 9600 M10]"
Option "AGPMode" "4"
Option "AGPFastWrite" "true"
Option "EnablePageFlip" "true"
Option "EnableDepthMoves" "true"
BusID "PCI:1:0:0" |
leider kommt mir das ganze noch immer ziemlich langsam vor... sieht jemand auf anhieb noch Verbesserungsmöglichkeiten an der Konfiguration oder hat noch ein paar Vorschläge zur Performancesteigerung....
[edit]
folgendes Sticht besonders hervor...
| Code: | | (WW) RADEON(0): Failed to set up write-combining range (0xd8000000,0x8000000) |
[/edit]
Danke schon im Vorraus und Grüße aus Berlin
Stefa |
|
| Back to top |
|
 |
Beforegod
Bodhisattva
Joined: 10 Apr 2002
Posts: 1495
Location: Würzburg
|
| Posted: Thu Jun 24, 2004 7:41 am Post subject: |
|
|
Nun, was erwartest Du.
Die einzige Möglichkeit ist das Nutzen der Kernel DRI Treiber, sonst nix.
Und die sind bei weitem nicht so ausgereift, das man damit ernsthaft 3D Nutzen kann. |
|
| Back to top |
|
|
stefanpropehan
n00b
Joined: 17 Jun 2004
Posts: 15
Location: Germany - Berlin
|
| Posted: Thu Jun 24, 2004 7:53 am Post subject: |
|
|
| Beforegod wrote: | | Nun, was erwartest Du. |
mhh habe ich doch geschrieben... ich dachte evtl. hat noch jemand ein paar Tip's zur Performancesteigerung...  und evtl wie die Fehlermeldung zu verstehen bzw zu beheben ist...
| Code: | | (WW) RADEON(0): Failed to set up write-combining range (0xd8000000,0x8000000) |
DRI im Kernel ist wie du schon geschrieben hast nicht wirklich eine Möglichkeit! Aber trozdem schon einmal danke für die Antwort  |
|
| Back to top |
|
|
genstef
Retired Dev
Joined: 13 Jun 2004
Posts: 668
Location: M/Bay/Germany
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Deutsches Forum (German)
