| View previous topic :: View next topic |
| Author |
Message |
phekko
Tux's lil' helper
Joined: 17 Feb 2004
Posts: 109
Location: Espoo Esbo
|
 Posted: Wed Jul 21, 2004 6:57 am Post subject: XFree ja 1600x1200-resoluutio |
 |
|
Heippistä hei ja hellät tunteet.
Mulla on ropleemi. Tarkemmin sanottuna ropleemi on se, että mulla on tässä tämmöttönen Toshiban Satellite Pro 6100-kannettava. Tosi kiva lelu. Mutta se ei halua olla kanssani yhteistyöhaluinen ollenkaan noiden maksimiresoluutioidensa suhteen.
Vempeleessä siis on NVidia Geforce Go 420 tai joku sellainen. Hyvä juttu, eikun emergettiin nvidia-kernel ja nvidia-glx ja editoihettiin XF86Config kohdalleen. Kaikki hyvin, homma toimii. Paitsi että resoluutio jää 1280x9jotain-tasolle. Kun editoi lisää configia, saa sen nostettua 1400x1050:an. Se on jo ihan kiva reso, ei siinä mitään. Mutta kun Winblowsissa tää masiina ihan kitisemättä osaa käyttää 1600x1200 ja olis se nyt kiva olla Linuxissakin.
Loki on vahvasti sitä mieltä, että 1600x1200 jää käyttämättä koska:
| Quote: |
(II) NVIDIA(0): Not using default mode "1600x1200" (hsync out of range)
|
tai vaihtoehtoisesti
| Quote: |
(II) NVIDIA(0): Not using default mode "1600x1200" (width too large for virtual size)
|
No joo. Tästä sitten suivaantuneena menin ja etsin modeline toolin. Se löytyi muuten osoitteesta http://www.dkfz-heidelberg.de/spec/linux/modeline/ ja tuntuu toimivan kun junan vessa. Sillä sitten editoitsin itselleni modelinet, jotka antaisivat a) 75Hz b) 60Hz ja c) edes 50Hz ulos 1600x1200-resoluutiolla. No perkele. Nehän antavat tyylikkäästi valkoiseksi muuttuvaa ruutua. Jossakin erottaa aluksi, että NVdian logoa se koittaa piirtää, mutta kovasti outoon paikkaan ja oudon muotoisena.
Alkaa pikkuhiljaa ajatukset loppua, joten ajattelin kysäistä olisiko teistä joku laittanut TFT-panelin toimimaan ja saanut homman onnistumaankin?
Ilmeisesti on ollut tapana laittaa se XF86Config mukaan tälläisiin, niin tässäpä se nyt sitten olisi . Anteeksi että se on siivoamaton. Osa on kopioitu weller.ws/toshiba -osoitteesta, koska siellä asusteleva jammu kuuleman mukaan on saanut omansa toimimaan. Eipä vaan toiminut minulla, perskeles | Quote: |
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# Video for Linux
Load "v4l"
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "speedo"
Load "freetype"
# Load "xtt"
# This loads the GLX module
Load "glx"
# wellerista taas:
Load "GLcore"
Load "bitmap"
Load "ddc"
Load "record"
Load "vbe"
# This loads the DRI module
Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
# FontPath "/usr/X11R6/lib/X11/fonts/TrueType/"
# FontPath "/usr/X11R6/lib/X11/fonts/freefont/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# The module search path. The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "Dont Zoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
# Option "Protocol" "Xqueue"
Option "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""
# Option "XkbDisable"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "fi"
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "Auto"
Option "Device" "/dev/mouse"
# rulla funkkimaan:
Option "ZAxisMapping" "4 5"
# Mouse-speed setting for PS/2 mouse.
# Option "Resolution" "256"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
# Option "Protocol" "Xqueue"
# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.
# Option "BaudRate" "9600"
# Option "SampleRate" "150"
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"
# ChordMiddle is an option for some 3-button Logitech mice
# Option "ChordMiddle"
EndSection
# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "toshiba tft"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 30-94 # plagioitu netista weller.ws/toshiba
VertRefresh 50-75
Option "DPMS"
Option "dcc" "off"
# DisplaySize 305 229
# Modeline tool: www.dkfz-heidelberg.de/spec/linux/modeline
# Modeline "1600x1200" 242.01 1600 1728 2024 2568 1200 1200 1204 1256
# Modeline "1600x1200" 170.89 1600 1688 1896 2288 1200 1200 1203 1244
# Modeline "1600x1200" 131.63 1600 1672 1832 2128 1200 1200 1202 1237
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "toshiba nv"
Driver "nvidia"
Option "IgnoreEDID" "true"
Option "CursorShadow" "1"
Option "CursorShadowAlpha" "63"
Option "CursorShadowYOffset" "2"
Option "CursorShadowXOffset" "4"
Option "RenderAccel" "true"
#VideoRam 65536
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "toshiba nv"
Monitor "toshiba tft"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1400x1050" "1280x1024" "1024x768" "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1400x1050" "1280x1024" "1024x768" "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1400x1050"
#"1280x1024" "1024x768"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Section "DRI"
Mode 0666
EndSection
|
|
|
| Back to top |
|
 |
crysaz
n00b
Joined: 10 May 2004
Posts: 13
|
| Posted: Fri Aug 20, 2004 8:59 am Post subject: |
|
|
IMO
Sun kannettavas ei hardware puolella pysty tuohon 1600x1200 resoluutioon. Windows on hoitanut homman kotiin muokkaamalla työpöydän sen näiköiseksi että resoluution olisi ko.
X serveri (ei ainkaan vakiona) ei pakkaa kuvaa mitenkänä. Se koittaa näyttää jokaisen pikselin siinä kohdassa missä sen kuuluisi ollakkin. Jos modeja tai horisontaalisia ja vertikaalisia virkistyksiä lähtee käsin säätämään mielivaltaisiksi, niin tft näytön oireilut voisi olla kuvamaasi kaltaisia. En tiedä kokemuksesta sanoa, mutta kuvaputkinäytön kuva rupee väpättämään eikö oikein pysy muutenkaan paikalla jos taajuuksissa on hieman heittoa.
Joku guru voi kertoa olenko oikeassa.
_________________
Life sucks and then you die. |
|
| Back to top |
|
|
jmz2
Guru
Joined: 13 Jan 2004
Posts: 421
Location: Finland
|
| Posted: Fri Aug 20, 2004 10:20 am Post subject: |
|
|
| Toshiban speksien mukaan 1400 x 1050 on suurin mahdollinen resoluutio. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Finnish
