| View previous topic :: View next topic |
| Author |
Message |
MaGuS
Guru
Joined: 13 Jun 2002
Posts: 303
Location: Luebeck, Germany
|
 Posted: Wed Jan 29, 2003 7:44 am Post subject: Getting prism2_cs to work? |
 |
|
Hi all,
last time I installed Gentoo on my notebook every think worked fine. This time I installed 1.4 rc2 and I cannot get my wireless pcmcia card working.
I complied the kernel without pcmcia support, but with hotplug support.
After reboot I emerged pcmcia-cs.
This works fine, here is the list of the modules:
ds 7304 2
i82365 27136 2
pcmcia_core 47072 0 [ds i82365]
If I now add the card the driver for it (last time it was the prism2 pcmica) won't be loaded. I tried to load it manual but I cannot find it, I only find prism2_plx and prism2_pci.
Can anybody tell me how to get the prism2 pcmcia driver?
Hope to get some help here, I need the wlan. 
MaGuS
Last edited by MaGuS on Fri Jan 31, 2003 3:28 pm; edited 2 times in total |
|
| Back to top |
|
 |
MaGuS
Guru
Joined: 13 Jun 2002
Posts: 303
Location: Luebeck, Germany
|
| Posted: Thu Jan 30, 2003 9:35 am Post subject: |
|
|
hehe I found it, I searched again in the froum and found this:
https://forums.gentoo.org/viewtopic.php?t=5046&highlight=prism2cs
Ok, so I cooked a new kernel with pcmcia support and cardbus support. Installed the modules, reboot.
After reboot I emerged linux-wlan-ng to get the prism2_cs modul.
I load 'pcmcia_core' and 'i82365', but with the 'i82365' I get an error about irq etc.
So I cooked a new kernel, without any PCMCIA support. I emerged pcmcia-cs and again linux-wlan-ng.
After reboot i load the moduls:
1. pcmcia_core
2. i82365
3. ds
4. prism2_cs
But now I get an error on loading prism2_cs:
| Code: |
Note: /etc/modules.conf is more recent than /lib/modules/2.4.20-gentoo-r1/modules.dep
/lib/modules/2.4.20-gentoo-r1/pcmcia/prism2_cs.o: init_module: Operation not permitted
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-gentoo-r1/pcmcia/prism2_cs.o: insmod /lib/modules/2.4.20-gentoo-r1/pcmcia/prism2_cs.o failed
/lib/modules/2.4.20-gentoo-r1/pcmcia/prism2_cs.o: insmod prism2_cs failed
|
dmesg:
| Code: |
-- SNIP ---
Linux PCMCIA Card Services 3.2.3
kernel build: 2.4.20-gentoo-r1 #10 SMP Fre Jan 31 14:10:33 CET 2003
options: [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
TI 1420 rev 00 PCI-to-CardBus at slot 00:0c, mem 0x10000000
host opts [0]: [ring] [pci + serial irq] [pci irq 10] [lat 168/176] [bus 2/5]
host opts [1]: [ring] [pci + serial irq] [pci irq 10] [lat 168/176] [bus 6/9]
spurious 8259A interrupt: IRQ7.
ISA irqs (scanned) = 3,4,7,11 PCI status changes
init_module: prism2_cs.o: 0.1.16-pre7 Loaded
init_module: dev_info is: prism2_cs
prism2_cs: CardServices release does not match!
p80211.o: 0.1.16-pre7 Unloaded
init_module: prism2_cs.o: 0.1.16-pre7 Loaded
init_module: dev_info is: prism2_cs
prism2_cs: CardServices release does not match!
p80211.o: 0.1.16-pre7 Unloaded
init_module: prism2_cs.o: 0.1.16-pre7 Loaded
init_module: dev_info is: prism2_cs
prism2_cs: CardServices release does not match!
p80211.o: 0.1.16-pre7 Unloaded
|
Could anybody help me getting my wlan card to work?
Last edited by MaGuS on Fri Jan 31, 2003 3:29 pm; edited 1 time in total |
|
| Back to top |
|
|
azote
Guru
Joined: 17 Sep 2002
Posts: 415
|
| Posted: Sat Feb 01, 2003 8:04 pm Post subject: |
|
|
where you able to fix this?
im having the same problem..
_________________
contact me -> azote@mail.i2p
What do you want to emerge today?
if you think that a person is normal, it is because you do not know them well |
|
| Back to top |
|
|
zentek
n00b
Joined: 03 Jul 2002
Posts: 41
|
| Posted: Sun Feb 02, 2003 5:05 pm Post subject: |
|
|
| I got the same problem. The only thing i had to do was to downgrade pcmica-cs to 3.2.1 . The wlan-ng driver require this version. |
|
| Back to top |
|
|
MaGuS
Guru
Joined: 13 Jun 2002
Posts: 303
Location: Luebeck, Germany
|
| Posted: Mon Feb 03, 2003 7:38 am Post subject: |
|
|
| cool, thank you. I will try it! |
|
| Back to top |
|
|
azote
Guru
Joined: 17 Sep 2002
Posts: 415
|
| Posted: Wed Feb 19, 2003 11:47 pm Post subject: how |
|
|
hey thanks but ... how do you get that version .. using emerge?
usually just gets the latest version of it ..
_________________
contact me -> azote@mail.i2p
What do you want to emerge today?
if you think that a person is normal, it is because you do not know them well |
|
| Back to top |
|
|
wwwdsummers
n00b
Joined: 25 Feb 2003
Posts: 11
|
| Posted: Wed Mar 05, 2003 1:48 pm Post subject: How I got it to work |
|
|
I had removed ISA support from my kernal - not knowing that you need ISA support to use a(ll?) pcmcia card(s). Once I added ISA support back into the kernal things started working  |
|
| Back to top |
|
|
|
Kernel & Hardware
