View previous topic :: View next topic |
Author |
Message |
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Wed Apr 28, 2004 8:32 pm Post subject: K3B and cdrdao start very slowly |
|
|
Hi,
K3B starts very slow. Also k3b-setup uses several minutes: I use:
- k3b 0.11.9
- kernel 2.4.25
- SCSI emulation
The drives are recognized by cdrecord:
Code: |
bash-2.05b$ cdrecord --scanbus
Cdrecord-Clone 2.01a25 (i586-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling
Linux sg driver version: 3.1.25
Using libscg version 'schily-0.8'.
scsibus0:
0,0,0 0) 'IDE-CD ' 'R/RW 4x4x24 ' '1.04' Removable CD-ROM
0,1,0 1) 'SONY ' 'DVD-ROM DDU1621 ' 'S1.5' Removable CD-ROM
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
|
Does anybody know what to do?
Regards
Last edited by samo on Fri May 21, 2004 5:39 am; edited 2 times in total |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Mon May 17, 2004 6:13 pm Post subject: |
|
|
Hi,
after I updated the kernel and cdrtools the problem is still pending:
- kernel 2.4.26
- cdrtools 2.01_alpha27
K3B needs "hours" to start.
Regards |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Fri May 21, 2004 5:37 am Post subject: |
|
|
Hi,
maybe it's a cdrdao and DMA problem. cdrdao needs "hours" to start. I read some other threads about this, but I didn't find a solution to enable DMA for my CD writer correctly.
The booting messages seem to be ok:
Code: |
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y080L0, ATA DISK drive
hdb: Maxtor 90576D4, ATA DISK drive
hdc: R/RW 4x4x24, ATAPI CD/DVD-ROM drive
hdd: DVD-ROM DDU1621, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=158816/16/63
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 11255328 sectors (5763 MB) w/256KiB Cache, CHS=11166/16/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 >
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3 p4 < p5 p6 >
|
Code: |
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
hdd: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: IDE-CD Model: R/RW 4x4x24 Rev: 1.04
Type: CD-ROM ANSI SCSI revision: 02
Vendor: SONY Model: DVD-ROM DDU1621 Rev: S1.5
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 0x/40x cd/rw xa/form2 cdda tray
|
hdparm doesn't work. Maybe scsi emulation isn't supported by hdparm.
Regards |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Sat May 22, 2004 9:35 am Post subject: |
|
|
I downgraded cdrdao from 1.1.8 to 1.1.7-r3. Now cdrdao and k3b starts immediately.
Could it be a bug in cdrdao 1.1.8? |
|
Back to top |
|
|
Lars Apprentice
Joined: 06 Feb 2003 Posts: 171 Location: Germany, near baltic sea
|
Posted: Mon Aug 09, 2004 12:59 pm Post subject: |
|
|
Maybe a problem with your build environment, is your CPU a K6?
Try CFLAGS with "-mcpu=i586" and rebuild cdrdao.
Lars _________________
Quote: | Alles was nicht einfach ist, ist entweder falsch oder zu kompliziert. |
V.Glazounov |
|
Back to top |
|
|
bmack500 n00b
Joined: 28 Sep 2003 Posts: 11 Location: Kentucky
|
Posted: Thu Sep 30, 2004 5:44 am Post subject: Downgrading CDRDAO worked for me too |
|
|
I was having the exact same issue with k3b starting very slowly (2.6.8-5 kernel, no scsi emulation, k6-3 processor). After downgrading it starts up instantly now.
PS, I have all the good cflags, but that wouldn't make as dramatic a difference as that. |
|
Back to top |
|
|
fabel n00b
Joined: 27 Jun 2004 Posts: 6
|
Posted: Fri Feb 04, 2005 11:25 pm Post subject: |
|
|
Lars wrote: | Maybe a problem with your build environment, is your CPU a K6?
Try CFLAGS with "-mcpu=i586" and rebuild cdrdao.
Lars |
Thanks a lot!
before "-march=k6-3" very long startup time
after "-march=i586" works well! _________________ Don't throw anything out of the windows,
but throw Windows out of everything! (abel) |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|