| View previous topic :: View next topic |
| Author |
Message |
BioSLuDge
Tux's lil' helper
Joined: 12 Jul 2004
Posts: 99
Location: Utah
|
 Posted: Wed May 18, 2005 7:35 am Post subject: can't mount my burner |
 |
|
I have an externel USB2 PlexWriter (PX-W4012TU) and I can't simply stick a cd in it and mount that cd. I fallowed the gentoo usb guide and when i type lsusb I get.
| Code: |
Bus 001 Device 002: ID 093b:0011 Plextor Corp.
Bus 001 Device 001: ID 0000:0000
|
Typing dmsg I find.
| Code: |
Freeing unused kernel memory: 220k freed
Vendor: PLEXTOR Model: CD-R PX-W4012A Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 00
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
usb-storage: device scan complete
|
and if i try to mount /dev/sg0 I receive the fallowing
| Code: |
mount: /dev/sg0 is not a block device
|
Thank you for your help
-BioSLuDge |
|
| Back to top |
|
 |
ikaro
Advocate
Joined: 14 Jul 2003
Posts: 2527
Location: Denmark
|
| Posted: Wed May 18, 2005 7:40 am Post subject: |
|
|
if you use a 2.6.x kernel you don't need scsi emulation.
if you try mount /dev/hdc /mnt/cdrom does it work ?
_________________
linux: #232767 |
|
| Back to top |
|
|
BioSLuDge
Tux's lil' helper
Joined: 12 Jul 2004
Posts: 99
Location: Utah
|
| Posted: Thu May 19, 2005 4:30 am Post subject: |
|
|
Ahhh, well mounting hdc only got my my internal DVD rom. I also tried all of my other hd devices (except my hard drive,hda) and none of those mounted.
Thanks for your time in advance.
-BioSLuDge |
|
| Back to top |
|
|
Fredde
Tux's lil' helper
Joined: 08 Feb 2005
Posts: 98
|
| Posted: Thu May 19, 2005 9:02 am Post subject: |
|
|
Hi!
hmm, if you run dmesg after you connected your plextor via USB, does it say anything about /dev/sda. When I connect a usb stick I have to mount /dev/sda1 to access it. So try to mount /dev/sda0 or /dev/sda1 and see if it works. |
|
| Back to top |
|
|
boogerman
Apprentice
Joined: 10 Dec 2004
Posts: 253
Location: Tennessee
|
| Posted: Thu May 19, 2005 12:27 pm Post subject: |
|
|
My external cd drive mounts as /dev/sr0, you might try that. Also, what USB support do you have enabled in your kernel? I had to enable a couple of things, unfortuantely I don't remember what and I'm at work so I can't look at it. But if you post the section from the make menuconfig I'll probably remember.
As a side note. Seeing the device in lsusb and dmesg doesn't mean you have the correct kernel config to get it to work. I often use lspci and lsusb to get information so that I can go and enable it in the kernel. Just thought I'd mention that incase you didn't know. |
|
| Back to top |
|
|
BioSLuDge
Tux's lil' helper
Joined: 12 Jul 2004
Posts: 99
Location: Utah
|
| Posted: Thu May 19, 2005 7:00 pm Post subject: |
|
|
After I unpluged and pluged the drive back in, dmesg shows this
| Code: |
usb 1-4: USB disconnect, address 5
usb 1-4: new high speed USB device using ehci_hcd and address 6
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
Vendor: PLEXTOR Model: CD-R PX-W4012A Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 00
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0, type 5
usb-storage: device scan complete
|
As for mounting to sda or sda0-8 I get
| Code: |
mount: No medium found
|
So thats probably my SD card reader that I have been looking for. And the sr's just return
| Code: |
mount: /dev/sr0 is not a valid block device
|
Thank you for your help and time
-BioSLuDge |
|
| Back to top |
|
|
BioSLuDge
Tux's lil' helper
Joined: 12 Jul 2004
Posts: 99
Location: Utah
|
| Posted: Thu May 19, 2005 7:50 pm Post subject: |
|
|
I copied my makemenu config for usb
| Code: |
<*> Support for Host-side USB
[ ] USB verbose debug messages
--- Miscellaneous USB options
[*] USB device filesystem
[ ] Enforce USB bandwidth allocation (EXPERIMENTAL)
[ ] Dynamic USB minor allocation (EXPERIMENTAL)
[ ] USB suspend/resume (EXPERIMENTAL)
--- USB Host Controller Drivers
<*> EHCI HCD (USB 2.0) support
[ ] Full speed ISO transactions (EXPERIMENTAL)
[ ] Root Hub Transaction Translators (EXPERIMENTAL)
< > OHCI HCD support
<*> UHCI HCD (most Intel and VIA) support
< > SL811HS HCD support
--- USB Device Class drivers
< > USB Audio support
< > USB Bluetooth TTY support
< > USB MIDI support
< > USB Modem (CDC ACM) support
<*> USB Printer support
--- NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
<*> USB Mass Storage support
[ ] USB Mass Storage verbose debug
[ ] USB Mass Storage Write-Protected Media Detection (EXPERIMENTAL)
[ ] Datafab Compact Flash Reader support (EXPERIMENTAL)
[ ] Freecom USB/ATAPI Bridge support
[ ] ISD-200 USB/ATA Bridge support
[ ] Microtech/ZiO! CompactFlash/SmartMedia support
[ ] HP CD-Writer 82xx sup[ ]
[*] SanDisk SDDR-09 (and other SmartMedia) support (EXPERIMENTAL)
[*] SanDisk SDDR-55 SmartMedia support (EXPERIMENTAL)
[ ] Lexar Jumpshot Compact Flash Reader (EXPERIMENTAL)
--- USB Input Devices
<*> USB Human Interface Device (full HID) support
[*] HID input layer support
[ ] Force feedback support (EXPERIMENTAL)
[ ] /dev/hiddev raw HID device support
< > Aiptek 6000U/8000U tablet support
< > Wacom Intuos/Graphire tablet support
< > KB Gear JamStudio tablet support
< > Griffin PowerMate and Contour Jog support
< > MicroTouch USB Touchscreen Driver
<M> eGalax TouchKit USB Touchscreen Driver
< > X-Box gamepad support
< > ATI / X10 USB RF remote control
--- USB Imaging devices
< > USB Mustek MDC800 Digital Camera support (EXPERIMENTAL)
< > Microtek X6USB scanner support
--- USB Multimedia devices
< > DABUSB driver
--- Video4Linux support is needed for USB Multimedia device support
USB Network Adapters --->
--- USB port drivers
USB Serial Converter support --->
--- USB Miscellaneous drivers
< > EMI 6|2m USB Audio interface support
< > EMI 2|6 USB Audio interface support
< > USB Auerswald ISDN support (EXPERIMENTAL)
< > USB Diamond Rio500 support (EXPERIMENTAL)
< > USB Lego Infrared Tower support (EXPERIMENTAL)
< > USB LCD driver support
< > USB LED driver support
<M> Cypress USB thermometer driver support
< > USB PhidgetKit support
<M> USB PhidgetServo support
< > Siemens ID USB Mouse Fingerprint sensor support
< > USB testing driver (DEVELOPMENT)
--- USB ATM/DSL drivers
USB Gadget Support --->port (EXPERIMENTAL)
|
Thanks again
-BioSLuDge |
|
| Back to top |
|
|
boogerman
Apprentice
Joined: 10 Dec 2004
Posts: 253
Location: Tennessee
|
| Posted: Thu May 19, 2005 9:03 pm Post subject: |
|
|
| try enabling OHCI HCD support under USB Host Controller Drivers, also on mine I have all the ata to IDE and ATAPI to IDE bridge support enabled, but I haven't tried it without it so I can't really tell you if it is necissary or not. |
|
| Back to top |
|
|
BioSLuDge
Tux's lil' helper
Joined: 12 Jul 2004
Posts: 99
Location: Utah
|
| Posted: Fri May 20, 2005 4:29 am Post subject: |
|
|
Still no luck, I tried mounting from everything above.
Thanks for your time
-BioSLuDge |
|
| Back to top |
|
|
|
Kernel & Hardware
