| View previous topic :: View next topic |
| Author |
Message |
mo-ca
Guru
Joined: 17 Feb 2003
Posts: 313
Location: Near Dresden, Germany
|
 Posted: Wed Mar 19, 2003 7:06 pm Post subject: cdrecord problem |
 |
|
moin
wenn ich versuche was zu brennen (egal was) bricht cdrecord bei mir immer bevor es irgendwas macht ab.
Hier die Ausgabe:
| Code: |
bash-2.05b# cdrecord -scanbus
Cdrecord 2.01a05 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilli
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
scsibus0:
0,0,0 0) 'SEAGATE ' 'ST318436LC ' '3252' Disk
0,1,0 1) 'SEAGATE ' 'ST39102LC ' '7502' Disk
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) 'TOSHIBA ' 'CD-ROM XM-6401TA' '1001' Removable CD-RO
0,7,0 7) *
scsibus1:
1,0,0 100) 'RICOH ' 'CD-R/RW MP7200A ' '1.30' Removable CD-RO
1,1,0 101) 'TEAC ' 'CD-532E-B ' '1.0A' Removable CD-RO
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
bash-2.05b# cdrecord dev=1,0,0 speed=4 /tmp/brenner/gbl-cd1.cue
Cdrecord 2.01a05 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilli
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'RICOH '
Identifikation : 'CD-R/RW MP7200A '
Revision : '1.30'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : MMC SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R
cdrecord: Drive needs to reload the media to return to proper status.
Starting to write CD/DVD at speed 4 in real TAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Turning BURN-Free off
cdrecord: Input/output error. read track info: scsi sendcmd: no error
CDB: 52 01 00 00 00 FF 00 00 1C 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0C 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 240s
bash-2.05b# cdrecord dev=1,0,0 speed=4 -vv /tmp/brenner/gbl-cd1.cue
Cdrecord 2.01a05 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilli
TOC Type: 1 = CD-ROM
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
Using libscg transport code version 'schily-scsi-linux-sg.c-1.75'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'RICOH '
Identifikation : 'CD-R/RW MP7200A '
Revision : '1.30'
Device seems to be: Generic mmc CD-RW.
Drive current speed: 4
Drive default speed: 20
Drive max speed : 20
Selected speed : 4
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : MMC SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R
Drive buf size : 1359872 = 1328 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 0 MB padsize: 598 KB
track: 1 start: 0 pregap: 150
Total size: 0 MB (00:04.02) = 302 sectors
Lout start: 1 MB (00:06/02) = 302 sectors
41 00 00 14 00 00 00 00
41 01 00 10 00 00 00 00
41 01 01 10 00 00 02 00
41 AA 01 14 00 00 06 02
Track 1 start 0
Track 2 start 302
41 00 A0 00 00 00 00 01 00 00 00 00
41 00 A1 00 00 00 00 01 00 00 00 00
41 00 A2 00 00 00 00 00 06 02 00 00
41 00 01 00 00 00 00 00 02 00 00 00
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -11933 (97:22/67)
ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 43
Manufacturer: Acer Media Technology, Inc.
Trying to clear drive status.
Forcespeed is OFF.
cdrecord: Drive needs to reload the media to return to proper status.
Forcespeed is OFF.
Starting to write CD/DVD at speed 4 in real TAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Performing OPC...
cdrecord: Input/output error. read track info: scsi sendcmd: no error
CDB: 52 01 00 00 00 FF 00 00 1C 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0C 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 240s
Writing time: 2.321s
Average write speed 566.4x.
Fixating...
Fixating time: 0.003s
cdrecord: fifo had 1 puts and 0 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
|
Wer kann mir hierfür nen Tipp geben?
danke[/code] |
|
| Back to top |
|
 |
Pylon
Retired Dev
Joined: 17 Jan 2003
Posts: 279
Location: Cologne
|
| Posted: Thu Mar 20, 2003 12:32 am Post subject: |
|
|
cdrecord kann keine .cue für ein .bin brennen.
Probiere mal 'cdrdao' stattdessen. Läuft bei mir ohne Probleme.
_________________
hacking is not a crime |
|
| Back to top |
|
|
mo-ca
Guru
Joined: 17 Feb 2003
Posts: 313
Location: Near Dresden, Germany
|
| Posted: Fri Mar 21, 2003 10:16 am Post subject: |
|
|
also danke erstmal, für die antwort, aber daran lags nicht.
ich habe mal cdrdao installiert und ich bekomme den gleichen Fehler mit Input/output Error. |
|
| Back to top |
|
|
Pylon
Retired Dev
Joined: 17 Jan 2003
Posts: 279
Location: Cologne
|
| Posted: Sat Mar 22, 2003 12:34 am Post subject: |
|
|
Hast Du überhaupt die SCSI-Emulation aktiviert? Sieht ja ganz nach einem IDE-Strang aus.
cdrecord kann mittlerweile auch direkt auf ATAPI zugreifen (Version >2 der cdrtools). Dazu einfach cdrecord dev=ATAPI:1,0,0 in diesem Fall aufrufen.
cdrdao hat dieses Feature noch nicht.
Was noch sein könnte, ist, dass Dein Brenner nicht SCSI-3/mmc-fähig ist und einen anderen Treiber braucht. Ich habe jetzt deswegen nicht viel gesucht, aber im doc-Verzeichnis zu cdrecord gibt es eine Liste mit den unterstützten Brennern und welchem Treiber.
_________________
hacking is not a crime |
|
| Back to top |
|
|
mo-ca
Guru
Joined: 17 Feb 2003
Posts: 313
Location: Near Dresden, Germany
|
| Posted: Sun Mar 23, 2003 1:32 pm Post subject: |
|
|
gut, was den kernel angeht, so kann ich folgendes sagen:
| Code: | # CONFIG_CISS_SCSI_TAPE is not set
CONFIG_BLK_DEV_IDESCSI=m
# SCSI support
CONFIG_SCSI=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
CONFIG_SCSI_AIC7XXX=y
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
|
das module ide-scsi is geladen
scnabus von cdrdao zeigt:
| Code: | bash-2.05b# cdrdao scanbus
Cdrdao version 1.1.7 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'andreas-0.5-UNIXWARE_Patch'
0,6,0: TOSHIBA, CD-ROM XM-6401TA, 1001
1,0,0: RICOH, CD-R/RW MP7200A, 1.30
1,1,0: TEAC, CD-532E-B, 1.0A
|
und beim brennen mit cdrdao kommt :
| Code: |
bash-2.05b# cdrdao write --device /dev/scd1 --driver ricoh-mp6200 -v 3 /tmp/brenner/Atlantis.cue
Cdrdao version 1.1.7 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'andreas-0.5-UNIXWARE_Patch'
Using libscg transport code version 'schily-scsi-linux-sg.c-1.68'
/dev/scd1: RICOH CD-R/RW MP7200A Rev: 1.30
Using driver: Ricoh MP6200 - Version 0.1(alpha) (options 0x0000)
Starting write at speed 10...
Pausing 10 seconds - hit CTRL-C to abort.
Process can be aborted with QUIT signal (usually CTRL-\).
?: Input/output error. : scsi sendcmd: no error
CDB: EE 00 00 00 00 00 00 00 04 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0C 00 00 00 00 20 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x20 Qual 0x00 (invalid command operation code) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s timeout 20s
ERROR: Cannot read session info.
ERROR: Writing failed.
|
ich hoffe, dass mit dieser detailreichen angaabe mir jemand helfen kann.
danke |
|
| Back to top |
|
|
jay
l33t
Joined: 08 May 2002
Posts: 980
|
| Posted: Sun Mar 23, 2003 3:23 pm Post subject: |
|
|
Hast Due es mal mit einem anderen Treiber probiert? Statt generic_mmc mal generic_mmc_raw ? Auf der Homepage von cdrdao gibt es eine Liste welcher Treiber für welchen Brenner zuständig ist.
_________________
Do you want your posessions identified? [ynq] (n) |
|
| Back to top |
|
|
mo-ca
Guru
Joined: 17 Feb 2003
Posts: 313
Location: Near Dresden, Germany
|
| Posted: Sun Mar 23, 2003 5:25 pm Post subject: |
|
|
 Peinlich
danke dir vielmals!
mit dem generic treiber kann cdrdao bei mir tatsächlich brennen.
Oh mann  |
|
| Back to top |
|
|
mo-ca
Guru
Joined: 17 Feb 2003
Posts: 313
Location: Near Dresden, Germany
|
| Posted: Mon Mar 24, 2003 4:49 pm Post subject: |
|
|
gut also wie gesagt, cdrdao brennt nun wie blöde
aber cdrecord will trotzdem nicht.
der nimmt automatisch den generic treiber, wie man sieht, aber immerwieder kommt ein fehler :< |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Deutsches Forum (German)
