| View previous topic :: View next topic |
| Author |
Message |
PyroBoy101
n00b
Joined: 07 Dec 2004
Posts: 37
Location: Bloomington NY
|
 Posted: Fri Aug 11, 2006 12:17 am Post subject: IVTV 0.7.0 and 2.6.17 issues |
 |
|
OK, I have a PVR-150 MCE that I installed in my system. The ebuild went fine after I selected all the appropriate kernel modules. I installed the new kernel, and rebooted.
Now the fun part comes when I go to load the module. I modprobe it and get this in dmesg:
| Code: | ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (tagged release) loading
ivtv: Linux version: 2.6.17-ck1-r2 SMP preempt mod_unload PENTIUM4 REGPARM gcc- 4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 19 (level, low) -> IRQ 19
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tuner 4-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ivtv0: Failed to load module tveeprom
tveeprom 4-0050: Hauppauge model 26582, rev F0B2, serial# 9307520
tveeprom 4-0050: tuner model is TCL M2523_5N_E (idx 112, type 50)
tveeprom 4-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 4-0050: audio processor is CX25843 (idx 37)
tveeprom 4-0050: decoder processor is CX25843 (idx 30)
tveeprom 4-0050: has no radio, has no IR remote
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 4-0061: type set to 50 (TCL 2002N)
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x4008646f!
ivtv0: i2c hardware 0x00000020 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
|
The modules that it complains about are infact there and load quietly when I do it myself.
I've been beating myself over the head with this all evening. Any help would be GREAT!
Thanks!
_________________
We need an airstrike! |
|
| Back to top |
|
 |
Ian
l33t
Joined: 28 Oct 2002
Posts: 834
Location: Somerville, MA
|
| Posted: Fri Aug 11, 2006 1:13 am Post subject: |
|
|
I have this same problem...except I just tried it and it worked...
*scratches head*
I have no idea what I just did, I tried reinstalling the kernel modules (cd /usr/src/linux; make modules modules_install), and when I tried to bring up /dev/video0 in mplayer, I got an image.
I'm quite confused because I tried it a minute before that and I just got static.
Err, well, it's working now, even with MythTV. I still have some errors in my dmesg, complaining about modules that won't load, but it seems to be working. I'll try rebooting in a bit, as soon as I finish compiling some stuff, and I'll see if it works after a reboot. |
|
| Back to top |
|
|
PyroBoy101
n00b
Joined: 07 Dec 2004
Posts: 37
Location: Bloomington NY
|
| Posted: Fri Aug 11, 2006 1:32 am Post subject: |
|
|
Funny... I just tried it again and now its working but with the same errors...
_________________
We need an airstrike! |
|
| Back to top |
|
|
Ian
l33t
Joined: 28 Oct 2002
Posts: 834
Location: Somerville, MA
|
| Posted: Fri Aug 11, 2006 1:42 am Post subject: |
|
|
Ok, so I rebooted, and it works! But I can't change channels, even with ivtv-tune.
Dmesg is still complaining about the modules not loading. I have another computer with a PVR-250 which was working fine with ivtv-0.7.0 and kernel 2.6.17, I'm not sure about the dmesg errors though. That computer is currently waiting for a new video card though, so I'm not sure if I'll be able to get it back up and running tonight.
So now I'm stuck watching "America's Got Talent"  . |
|
| Back to top |
|
|
Ian
l33t
Joined: 28 Oct 2002
Posts: 834
Location: Somerville, MA
|
| Posted: Fri Aug 11, 2006 3:50 am Post subject: |
|
|
I had IvTV 0.4.x running on this computer with 2.6.15 before, I've noticed a lot of things changed, like not having to define tuner type, I wonder if I missed a file somewhere?
Does anyone know which files would have to be modified after such an upgrade? |
|
| Back to top |
|
|
Ian
l33t
Joined: 28 Oct 2002
Posts: 834
Location: Somerville, MA
|
| Posted: Fri Aug 11, 2006 3:55 am Post subject: |
|
|
Huzzah!
As soon as I posted that I found /etc/modules.d/ivtv, so I tried moving it, and reloading the driver, now I can change channels again! |
|
| Back to top |
|
|
PyroBoy101
n00b
Joined: 07 Dec 2004
Posts: 37
Location: Bloomington NY
|
| Posted: Fri Aug 11, 2006 6:58 pm Post subject: |
|
|
Now if I could just get YUV video and PCM audio to play remotely in sync...
_________________
We need an airstrike! |
|
| Back to top |
|
|
Ian
l33t
Joined: 28 Oct 2002
Posts: 834
Location: Somerville, MA
|
| Posted: Fri Aug 11, 2006 10:33 pm Post subject: |
|
|
Well this is sure turing into a pain quickly.
I rebooted my computer, reloaded all of them modules, and I cannot change channels again. At least it's stuck on SciFi now, which sure beats Fox or whatever I was stuck on before. |
|
| Back to top |
|
|
jacobmar1ey
n00b
Joined: 02 Jun 2004
Posts: 8
Location: Worcester, MA, USA
|
| Posted: Mon Aug 14, 2006 12:19 am Post subject: |
|
|
I was having trouble setting CONFIG_VIDEO_TVEEPROM for a while, but then I figured out I needed to set my config options thusly (in make menuconfig):
<*> Video For Linux
│ │[*] Enable Video For Linux API 1 (DEPRECATED)
│ │--- Enable Video For Linux API 1 compatible Layer
If it wasn't on the (DEPRECATED) option, there would be no TVEEPROM in my .config at all! |
|
| Back to top |
|
|
Caeberos
Tux's lil' helper
Joined: 24 Mar 2004
Posts: 109
|
| Posted: Wed Aug 16, 2006 7:39 pm Post subject: |
|
|
I am having the same problem except my computer reports
ivtv0: Failed to load module tuner
ivtv0: Failed to load module tda9887
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
I am not sure where the first two modules are located, and I have never once been able to get live tv working |
|
| Back to top |
|
|
JDCentral
Tux's lil' helper
Joined: 06 Nov 2004
Posts: 112
Location: Fort Collins, CO
|
| Posted: Wed Aug 16, 2006 8:14 pm Post subject: |
|
|
haha - I JUST got this card in the mail, today, and plan on attempting to get it working, tonight.
Wish me luck... I'll let you know how it goes.
_________________
Gentoo Currently installed on:
Athlon XP-Mobile Barton 2600+ @ 200x12.5
ASUS A7N8X Deluxe. rev 2.0
1GB OCZ Performance PC3200 RAM
Sapphire X1650 Pro 256MB GDDR3
2x120GB Seagate 7200.1 IDE Drives
1x320GB Seagate SATA Drive |
|
| Back to top |
|
|
bocacorazon
n00b
Joined: 07 May 2004
Posts: 31
|
| Posted: Sun Aug 27, 2006 6:13 pm Post subject: Any luck so far? |
|
|
I have not been able to get the PVR-150 running on a kernel-2.6.17 and ivtv-0.7 on an AMD64 machine
I've found several threads on the issue but none actually resolved...
My dmesg:
| Code: |
ivtv: version 0.7.0 (tagged release) loading
ivtv: Linux version: 2.6.17-gentoo-r4 SMP mod_unload gcc-3.4
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
GSI 23 sharing vector 0xE1 and IRQ 23
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 225
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: Failed to load module tveeprom
tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 8296168
tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is CX25841 (idx 35)
tveeprom 0-0050: decoder processor is CX25841 (idx 28)
tveeprom 0-0050: has no radio, has IR remote
ivtv0: Failed to load module tuner
ivtv0: Failed to load module tda9887
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x4008646f!
ivtv0: i2c hardware 0x00000020 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
|
file /bin/bash
| Code: |
/bin/bash: ELF 64-bit LSB executable, AMD x86-64, version 1 (SYSV), for GNU/Linux 2.4.1, dynamically linked (uses shared libs), stripped
|
modinfo ivtv
| Code: |
version: 0.7.0 (tagged release)
license: GPL
description: CX23415/CX23416 driver
author: Kevin Thayer, Chris Kennedy, Hans Verkuil
parm: ivtv_first_minor:Set minor assigned to first card
parm: newi2c:Use new I2C implementation
default is 1 (yes)
parm: max_dec_osd_buffers:Max Dec OSD Buffers (in megs)
Default: 2
parm: dec_osd_buffers:Dec OSD buffers (in megs)
Default: 1
parm: max_dec_vbi_buffers:Max Dec VBI Buffers (in megs)
Default: 1
parm: dec_vbi_buffers:Dec VBI buffers (in megs)
Default: 1
parm: max_dec_yuv_buffers:Max Dec YUV Buffers (in megs)
Default: 1
parm: dec_yuv_buffers:Dec YUV buffers (in megs)
Default: 1
parm: max_dec_mpg_buffers:Max Dec MPG Buffers (in megs)
Default: 1
parm: dec_mpg_buffers:Dec MPG buffers (in megs)
Default: 1
parm: max_pcm_buffers:Max Enc PCM Buffers (in megs)
Default: 16
parm: pcm_buffers:Enc PCM buffers (in megs)
Default: 2
parm: max_vbi_buffers:Max Enc VBI Buffers (in megs)
Default: 16
parm: vbi_buffers:Enc VBI Buffers (in megs)
Default: 2
parm: max_yuv_buffers:Max Enc YUV Buffers (in megs)
Default: 32
parm: yuv_buffers:Enc YUV Buffers (in megs)
Default: 2
parm: max_mpg_buffers:Max Enc MPG Buffers (in megs)
Default: 16
parm: mpg_buffers:Enc MPG Buffers (in megs)
Default: 4
parm: ivtv_dfw:Decoder firmware image
Default: v4l-cx2341x-dec.fw
parm: ivtv_efw:Encoder firmware image
Default: v4l-cx2341x-enc.fw
parm: ivtv_yuv_threshold:If ivtv_yuv_mode is 2 (auto) then playback content as
progressive if src height <= ivtv_yuvthreshold
Default: 480
parm: ivtv_yuv_mode:Specify the yuv playback mode:
0 = interlaced
1 = progressive
2 = auto
Default: 0 (interlaced)
parm: ivtv_pci_latency:Change the PCI latency to 64 if lower: 0 = No, 1 = Yes,
Default: Yes
parm: ivtv_dynbuf:Specify using Dynamic Buffers: 0 = No, 1 = Yes,
Default: No
parm: ivtv_debug:Debug level (bitmask). Default: errors only
(ivtv_debug = 511 gives full debugging)
parm: ntsc:Set NTSC standard: M, J, K
parm: secam:Set SECAM standard: B, G, H, D, K, L, LC
parm: pal:Set PAL standard: B, G, H, D, K, I, M, N, Nc
parm: cardtype:Only use this option if your card is not detected properly.
Specify card type:
1 = WinTV PVR 250
2 = WinTV PVR 350
3 = WinTV PVR-150 or PVR-500
4 = AVerMedia M179
5 = YUAN MPG600/Kuroutoshikou iTVC16-STVLP
6 = YUAN MPG160/Kuroutoshikou iTVC15-STVLP
7 = YUAN PG600/DIAMONDMM PVR-550 (CX Falcon 2)
8 = Adaptec AVC-2410
9 = Adaptec AVC-2010
10 = NAGASE TRANSGEAR 5000TV
11 = AOpen VA2000MAX-STN6
12 = YUAN MPG600GR/Kuroutoshikou CX23416GYC-STVLP
13 = I/O Data GV-MVP/RX
14 = I/O Data GV-MVP/RX2E
15 = GOTVIEW PCI DVD
16 = GOTVIEW PCI DVD2 Deluxe
17 = Yuan MPC622
18 = Digital Cowboy DCT-MTVP1
Default: Autodetect
parm: radio:Enable or disable the radio. Use only if autodetection
fails. 0 = disable, 1 = enable
parm: tuner:Tuner type selection,
see tuner.h for values
parm: yuv_fixup:Toggles conversion of Hauppauge
Macroblock NV12 to NV12
parmtype: newi2c:int
parmtype: max_dec_osd_buffers:int
parmtype: max_dec_vbi_buffers:int
parmtype: max_dec_yuv_buffers:int
parmtype: max_dec_mpg_buffers:int
parmtype: max_pcm_buffers:int
parmtype: max_vbi_buffers:int
parmtype: max_yuv_buffers:int
parmtype: max_mpg_buffers:int
parmtype: dec_osd_buffers:int
parmtype: dec_vbi_buffers:int
parmtype: dec_yuv_buffers:int
parmtype: dec_mpg_buffers:int
parmtype: pcm_buffers:int
parmtype: vbi_buffers:int
parmtype: yuv_buffers:int
parmtype: mpg_buffers:int
parmtype: ivtv_first_minor:int
parmtype: ivtv_dfw:charp
parmtype: ivtv_efw:charp
parmtype: ivtv_yuv_threshold:int
parmtype: ivtv_yuv_mode:int
parmtype: ivtv_pci_latency:int
parmtype: ivtv_dynbuf:int
parmtype: ivtv_debug:int
parmtype: ntsc:string
parmtype: secam:string
parmtype: pal:string
parmtype: cardtype:array of int
parmtype: radio:array of bool
parmtype: tuner:array of int
parmtype: yuv_fixup:int
srcversion: F969036064F79D72612388A
alias: pci:v00004444d00000016sv*sd*bc*sc*i*
alias: pci:v00004444d00000803sv*sd*bc*sc*i*
depends: tveeprom,i2c-core,i2c-algo-bit
vermagic: 2.6.17-gentoo-r4 SMP mod_unload gcc-3.4
|
make.conf
| Code: |
CFLAGS="-O2 -pipe -march=k8 -fomit-frame-pointer"
CHOST="x86_64-pc-linux-gnu"
CXXFLAGS="${CFLAGS}"
MAKEOPTS="-j2"
USE="X qt alsa dvd cdr mysql samba -gtk -gnome -gtk2 encode automount ffmpeg hal dbus jpeg lirc nvidia mp3 mpeg opengl png python readline v4l mythtv apache2 usb real mp3"
INPUT_DEVICES="keyboard mouse"
VIDEO_CARDS="nvidia"
ALSA_CARDS="emu10k1"
GENTOO_MIRRORS="ftp://darkstar.ist.utl.pt/pub/gentoo/ ftp://ftp.uni-erlangen.de/pub/mirrors/gentoo http://trumpetti.atm.tut.fi/gentoo/"
LIRC_OPTS="--with-driver=hauppauge"
|
I am trying to set the tuner manually but I cannot find the numbers for the 150 NTSC tuners
| Code: |
nina modules.d # grep Hauppauge /usr/src/linux-2.6.17-gentoo-r4/include/media/tuner.h
#define TUNER_TCL_2002MB 55 /* Hauppauge PVR-150 PAL */
#define TUNER_PHILIPS_FQ1216AME_MK4 56 /* Hauppauge PVR-150 PAL */
#define TUNER_PHILIPS_FQ1236A_MK4 57 /* Hauppauge PVR-500MCE NTSC */
#define TUNER_SAMSUNG_TCPN_2121P30A 70 /* Hauppauge PVR-500MCE NTSC */
|
my lsmod:
| Code: |
ivtv 176656 0
nvidia 5420052 12
snd_seq_midi 8768 0
snd_emu10k1_synth 8640 0
snd_emux_synth 31488 1 snd_emu10k1_synth
snd_seq_virmidi 7936 1 snd_emux_synth
snd_seq_midi_event 8768 2 snd_seq_midi,snd_seq_virmidi
snd_seq_midi_emul 7872 1 snd_emux_synth
snd_seq 49824 5 snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_event,snd_seq_midi_emul
snd_pcm_oss 38880 0
snd_mixer_oss 16704 1 snd_pcm_oss
snd_emu10k1 111364 1 snd_emu10k1_synth
snd_rawmidi 22880 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1
snd_ac97_codec 99416 1 snd_emu10k1
snd_ac97_bus 4608 1 snd_ac97_codec
snd_pcm 80328 3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_seq_device 8204 4 snd_seq_midi,snd_emu10k1_synth,snd_emu10k1,snd_rawmidi
snd_timer 21448 3 snd_seq,snd_emu10k1,snd_pcm
snd_page_alloc 9744 2 snd_emu10k1,snd_pcm
snd_util_mem 5888 2 snd_emux_synth,snd_emu10k1
snd_hwdep 9864 2 snd_emux_synth,snd_emu10k1
snd 50504 12 snd_emux_synth,snd_seq_virmidi,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_hwdep
i2c_algo_bit 10248 1 ivtv
tveeprom 17232 1 ivtv
i2c_core 19776 4 ivtv,nvidia,i2c_algo_bit,tveeprom
|
I'll apreciate any input you might have.
Thanks
[/code] |
|
| Back to top |
|
|
jacobmar1ey
n00b
Joined: 02 Jun 2004
Posts: 8
Location: Worcester, MA, USA
|
| Posted: Sun Aug 27, 2006 7:38 pm Post subject: Re: Any luck so far? |
|
|
| bocacorazon wrote: | I have not been able to get the PVR-150 running on a kernel-2.6.17 and ivtv-0.7 on an AMD64 machine
I've found several threads on the issue but none actually resolved...
My dmesg:
| Code: |
ivtv: version 0.7.0 (tagged release) loading
ivtv: Linux version: 2.6.17-gentoo-r4 SMP mod_unload gcc-3.4
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
GSI 23 sharing vector 0xE1 and IRQ 23
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 225
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: Failed to load module tveeprom
tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 8296168
tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is CX25841 (idx 35)
tveeprom 0-0050: decoder processor is CX25841 (idx 28)
tveeprom 0-0050: has no radio, has IR remote
ivtv0: Failed to load module tuner
ivtv0: Failed to load module tda9887
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x4008646f!
ivtv0: i2c hardware 0x00000020 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
|
...
I'll apreciate any input you might have.
Thanks
[/code] |
I found that trying to modprobe things in the v4l modules directory in /lib/modules would load certain modules, which after unloading and loading the ivtv module, would resolve those i2c hardware messages. I can check when I get home which helped on my PVR-250. |
|
| Back to top |
|
|
bilbravo
Guru
Joined: 30 May 2003
Posts: 319
Location: Baltimore, MD
|
| Posted: Sat Sep 09, 2006 4:15 pm Post subject: |
|
|
| Caeberos wrote: | I am having the same problem except my computer reports
ivtv0: Failed to load module tuner
ivtv0: Failed to load module tda9887
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
I am not sure where the first two modules are located, and I have never once been able to get live tv working |
Make sure those are set as <M> in your kernel config. Just open your .config file (/usr/src/linux/.config) and search for those modules.
Ian:
I'm having the same issue as you, get a picture but can't change channels. Any update on your situation?
_________________
me |
|
| Back to top |
|
|
darkpenguin
n00b
Joined: 28 Oct 2005
Posts: 32
|
| Posted: Wed Sep 20, 2006 1:27 pm Post subject: |
|
|
Good Morning guys.
Has anyone gotten this problem resolved? I started a thread here :
https://forums.gentoo.org/viewtopic-t-499629.html
It looks like PyroBoy is having the same issue as I, and is also using gcc 4.1. I have had a few replies to my thread of people that have ivtv working with the 2.6.17 kernel, but they are also using the gcc 3.4.x.[/glep] |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
