Rukie
l33t
Joined: 26 Jan 2004
Posts: 692
Location: SE Wi, Home of cheese and cowtippers.......
|
 Posted: Fri Feb 02, 2007 3:23 am Post subject: WPA-PSK with bcm43xx |
 |
|
when setupping up ndiswrapper (following https://forums.gentoo.org/viewtopic-t-516342-highlight-howto+wpa.html) I get an erorr.
gentootop Desktop # ndiswrapper -i /lib/firmware/bcmwl5.inf
installing bcmwl5 ...
couldn't find models section "BROADCOM" -
installation may be incomplete
ndiswrapper -l shows this
gentootop Desktop # ndiswrapper -l
bcmwl5 : invalid driver!
mn720-ankh : driver installed
device (14E4:4325) present (alternate driver: bcm43xx)
anyways,
my wpa_supplicant.conf is
gentootop Desktop # cat /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
# Example blocks:
# WPA-PSK
network={
scan_ssid=1
proto=WPA
#proto=RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP WEP104 WEP40
ssid="cchswireless"
#psk="2544355676"
psk=e0c2a3dc17604eab9385039d42a4538276a1a8ec5749dbe036b8eacb78f70945
priority=2
}
these are the errors/logs I had from wpa_supplicant
| Quote: |
gentootop firmware # wpa_supplicant -dd -ieth1 -c/etc/wpa_supplicant.conf -Dndiswrapper
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='0' (DEPRECATED)
eapol_version=1
ap_scan=1
fast_reauth=1
Line: 10 - start of a new network block
scan_ssid=1 (0x1)
proto: 0x1
key_mgmt: 0x2
pairwise: 0x18
group: 0x1e
ssid - hexdump_ascii(len=12):
63 63 68 73 77 69 72 65 6c 65 73 73 cchswireless
PSK - hexdump(len=32): [REMOVED]
priority=2 (0x2)
Priority group 2
id=0 ssid='cchswireless'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xd
capabilities: key_mgmt 0x5 enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:0d:3a:25:4d:71
Driver does not support WPA.
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Setting scan request: 0 sec 100000 usec
ctrl_interface_group=0
Added interface eth1
RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=12):
63 63 68 73 77 69 72 65 6c 65 73 73 cchswireless
Trying to get current scan results first without requesting a new scan to speed up initial association
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
Scan results: -1
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
Scan results: -1
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b2a len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=14
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b04 len=12
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=12):
63 63 68 73 77 69 72 65 6c 65 73 73 cchswireless
Scan timeout - try to get results
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
Scan results: -1
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan (broadcast SSID)
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface eth1
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Failed to disable WPA in the driver.
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6
|
any ideas at at all guys?
_________________
Gentoomania! Support the Open Source!
http://www.rukie.ath.cx |
|
Networking & Security
