Gentoo Forums :: View topic - Kein Brennen von CD/DVD mehr möglich [solved]

Kein Brennen von CD/DVD mehr möglich [solved]

View unanswered posts
View posts from last 24 hours
View posts from last 7 days

Gentoo Forums Forum Index

Deutsches Forum (German)

View previous topic :: View next topic

Author

Message

trikolon
Apprentice

Joined: 04 Dec 2004
Posts: 297
Location: Erlangen

Posted: Sun Oct 04, 2009 12:20 pm Post subject: Kein Brennen von CD/DVD mehr möglich [solved]

Hallo alle,
seit gestern kann ich keine CDs oder DVDs mehr brennen. Probiert habe ich Nero und K3b mit gleichen Erfolg, wenn er kalibriert hat und loslegen will kommt eine Fehlermeldung (K3b sagt mkisofs ist gecrasht).
Dmesg gibt folgendes aus:

Code:

ata2.00: status: { DRDY ERR }
ata2: hard resetting link
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: configured for PIO0
ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t4
ata2: irq_stat 0x40000001
ata2.00: configured for PIO0
ata2: EH complete
ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x400101 action 0x6 frozen
ata2.00: irq_stat 0x08000000, interface fatal error
ata2: SError: { RecovData UnrecovData Handshk }
ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
cdb 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: configured for PIO0
ata2: EH complete
ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x400100 action 0x6 frozen
ata2.00: irq_stat 0x08000000, interface fatal error
ata2: SError: { UnrecovData Handshk }
ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
cdb 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: configured for PIO0
ata2: EH complete

Weiss da jemand rat? Kernel habe ich Version 30 und 31 getestet. Ist das Laufwerk kaputt?

Gruß Ben

Last edited by trikolon on Sun Oct 04, 2009 2:02 pm; edited 1 time in total

mv
Watchman

Joined: 20 Apr 2005
Posts: 6780

Posted: Sun Oct 04, 2009 12:28 pm Post subject:

Benutzt Du das mkisofs aus app-cdr/cdrtools? Falls nein, würde ich es mal damit versuchen...

trikolon
Apprentice

Joined: 04 Dec 2004
Posts: 297
Location: Erlangen

Posted: Sun Oct 04, 2009 1:00 pm Post subject:

habe ich nun gemacht, brennen klappt leider immer noch nicht. hier das k3b log.

Code:

Devices
-----------------------
LITE-ON DVDRW LH-20A1L BL05 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]

K3b::IsoImager
-----------------------
mkisofs print size result: 357047 (731232256 bytes)

System
-----------------------
K3b Version: 1.66.0
KDE Version: 4.3.1 (KDE 4.3.1)
QT Version: 4.5.2
Kernel: 2.6.31-gentoo-r1

Used versions
-----------------------
mkisofs: 2.1.1a65
cdrecord: 2.1.1a65

cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
/usr/bin/cdrecord: Warning: The DMA speed test has been skipped.
Cdrecord-ProDVD-ProBD-Clone 2.01.01a65 (x86_64-unknown-linux-gnu) Copyright (C) 1995-2009 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.9'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'LITE-ON '
Identifikation : 'DVDRW LH-20A1L '
Revision : 'BL05'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: CD-R
Profile: DVD+R/DL
Profile: DVD+R
Profile: DVD+RW
Profile: DVD-R/DL layer jump recording
Profile: DVD-R/DL sequential recording
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD-RAM
Profile: DVD-R sequential recording
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R (current)
Profile: CD-ROM
Profile: Removable Disk
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R LAYER_JUMP
Drive buf size : 988416 = 965 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 697 MB
Total size: 800 MB (79:20.62) = 357047 sectors
Lout start: 801 MB (79:22/47) = 357047 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 4
Disk Is not unrestricted
Disk Is not erasable
Disk sub type: Medium Type A, low Beta category (A-) (2)
ATIP start of lead in: -12508 (97:15/17)
ATIP start of lead out: 359845 (79:59/70)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 22
Manufacturer: Ritek Co.
Capacity Blklen/Sparesz. Format-type Type
449849 2048 0x00 No Media Present or Unknown Capacity
Blocks total: 359845 Blocks current: 359845 Blocks remaining: 2798
Forcespeed is OFF.
Starting to write CD/DVD/BD at speed 48 in real SAO mode for single session.
Last chance to quit, starting real write in 3 seconds.
2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Turning BURN-Free on
Performing OPC...
Sending CUE sheet...
/usr/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 FF FF FF 6A 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 03 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x03 (setmark detected) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 3.568s timeout 200s
/usr/bin/cdrecord: Input/output error. read buffer cap: scsi sendcmd: no error
CDB: 5C 00 00 00 00 00 00 00 0C 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x04 Qual 0x01 (logical unit is in process of becoming ready) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.666s timeout 200s
Writing pregap for track 1 at -150
write track pad data: error after 0 bytes
Starting new track at sector: 0
Track 01: 0 of 697 MB written.
/usr/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x04 Qual 0x01 (logical unit is in process of becoming ready) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.327s timeout 200s
/usr/bin/cdrecord: A write error occured.
/usr/bin/cdrecord: Please properly read the error message above.
write track data: error after 0 bytes
Writing time: 20.271s
Average write speed 450.8x.
Fixating...
Fixating time: 0.350s
/usr/bin/cdrecord: fifo had 64 puts and 1 gets.
/usr/bin/cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
BURN-Free was never needed.

cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/sr0 speed=48 -sao driveropts=burnfree -data -tsize=357047s -

mkisofs
-----------------------
357047
/usr/bin/mkisofs: Warning: Cannot add inode hints with -no-cache-inodes.
=== last message repeated 2 times. ===
Setting input-charset to 'UTF-8' from locale.
0.14% done, estimate finish Sun Oct 4 16:19:37 2009
0.28% done, estimate finish Sun Oct 4 15:39:27 2009
0.42% done, estimate finish Sun Oct 4 15:25:48 2009
0.56% done, estimate finish Sun Oct 4 15:18:46 2009

mkisofs calculate size command:
-----------------------
/usr/bin/mkisofs -gui -graft-points -print-size -quiet -volid DD -volset -appid K3B THE CD KREATOR (C) 1998-2007 SEBASTIAN TRUEG -publisher -preparer -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-ben/k3bD11052.tmp -rational-rock -hide-list /tmp/kde-ben/k3bu11052.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-ben/k3bj11052.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 3 -path-list /tmp/kde-ben/k3bo11052.tmp

mkisofs command:
-----------------------
/usr/bin/mkisofs -gui -graft-points -volid DD -volset -appid K3B THE CD KREATOR (C) 1998-2007 SEBASTIAN TRUEG -publisher -preparer -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-ben/k3bh11052.tmp -rational-rock -hide-list /tmp/kde-ben/k3bS11052.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-ben/k3bK11052.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 3 -path-list /tmp/kde-ben/k3bs11052.tmp

trikolon
Apprentice

Joined: 04 Dec 2004
Posts: 297
Location: Erlangen

Posted: Sun Oct 04, 2009 2:02 pm Post subject:

ich habe das sata kabel am mainboard abgemacht und es auf einen anderen noch freien sata port gelegt. nun geht wieder alles.. sehr seltsam.. danke für die hilfe

Display posts from previous:

	Gentoo Forums Forum Index Deutsches Forum (German)	All times are GMT
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Copyright 2001-2025 Gentoo Foundation, Inc. Designed by Kyle Manna © 2003; Style derived from original subSilver theme. | Hosting by Gossamer Threads Inc. © | Powered by phpBB 2.0.23-gentoo-p11 © 2001, 2002 phpBB Group
Privacy Policy