| View previous topic :: View next topic |
| Author |
Message |
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
 Posted: Wed Aug 22, 2018 5:24 pm Post subject: |
 |
|
NeddySeagoon,
I didn't realize the Portage tree was already available in squashfs form - that's helpful to know, as I the version I distribute isn't modified from that much (just some additional signed hash verification, which is redundant now gemato has gone live - all the other customizations are done via overlay).
antonlacon,
thanks for the scripts, I'll take a look.
_________________
Regards,
sakaki |
|
| Back to top |
|
 |
orion777
Apprentice
Joined: 15 Mar 2017
Posts: 207
Location: Riga, Latvia
|
| Posted: Sat Aug 25, 2018 6:00 am Post subject: |
|
|
Where are PYTHON TARGETS are stored in?
Now my system (probably after casually made config update by emerge) require python 3.6 install. This, itself, cause massive reinstallation of installed packages to enable python 3.6 use flag, so I afraid of genup which will run --newuse.
So, how to roll back python targets to 2.7 and 3.5 only? Gentoo wiki refers to files, that does not exists in this setup.. |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54578
Location: 56N 3W
|
| Posted: Sat Aug 25, 2018 9:06 am Post subject: |
|
|
orion777,
PYTHON_TARGETS is a use expand and can be set in make.conf
| Code: | PYTHON_TARGETS="python2_7 python3_6"
PYTHON_SINGLE_TARGET="python3_4" |
That's an example, which I had commented out in my make.conf.
Only use these settings to delay the inevitable. You will have to do the upgrade sometime.
Doesn't genup install binaries?
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Sat Aug 25, 2018 5:09 pm Post subject: |
|
|
orion777,
on the gentoo-on-rpi3-64bit image, PYTHON_TARGETS (and PYTHON_SINGLE_TARGET) is usually controlled by the "base" parent profile, via /usr/portage/profiles/base/make.defaults. As this news article states:
| Quote: | On 2018-06-22, Python 3.6 will replace Python 3.5 in the default Python
targets for Gentoo systems. The new default targets will be:
PYTHON_TARGETS="python2_7 python3_6"
PYTHON_SINGLE_TARGET="python3_6" |
However, I have temporarily overridden PYTHON_TARGETS in the custom profile used by the image (you can see the edit in the file /usr/local/portage/rpi3/profiles/targets/rpi3/make.defaults on your system; this custom profile inherits inter alia from the base profile). This means that currently, you will have: | Code: | PYTHON_TARGETS="python2_7 python3_5 python3_6"
PYTHON_SINGLE_TARGET="python3_6" |
(You can check this via emerge --info) This overlap with 3.5 was done to prevent issues during the cutover to 3.6; it will be removed in a little while.
On the image, a gated copy of the Portage tree is used. What happens during the weekly update cycle is that my RPi3 buildserver updates its copy of the Portage tree (using webrsync-gpg) from upstream, and then attempts a full genup run (which builds any upgraded packages, and rebuilds packages with changed USE flags etc - the genup manpage is available here). As the server runs with buildpkg set in FEATURES, successfully built packages automatically create a matching (local) binary package. If there are any issues, I add custom USE flags / package.mask entries etc. into the custom profile, until the build goes through OK. I then test any newly upgraded major packages (GIMP etc.) to check nothing major appears broken. If good, the binary packages are rsync'd up to the binhost (https://isshoni.org/pi64pie, in this case), the Portage tree snapshot is signed (using porthash) and also rsync'd to the isshoni server, and any commits to the custom profile (new masks etc) are pushed to GitHub.
When you run genup on your copy of the image, it will update the rpi3-overlay (which will pull in any custom masks etc. from GitHub) and also the 'gated' copy of the Portage tree. It will then attempt to run a full @world update, and, since the image has getbinpkg set in FEATURES, will check the https://isshoni.org/pi64pie binhost for binary packages (with matching USE flags etc.) before building locally.
As such, NeddySeagoon is correct, in that when you hit a major USE flag change (such as the move to python3_6), appropriately built (or rebuilt) binary packages should already be available on the binhost, so the upgrade should not be painful. Of course, if you have a lot of local USE flag changes, or custom-installed packages, you may still have some local compilation work to do.
I discuss the weekly gated tree, custom profile etc. in more detail here.
_________________
Regards,
sakaki |
|
| Back to top |
|
|
orion777
Apprentice
Joined: 15 Mar 2017
Posts: 207
Location: Riga, Latvia
|
| Posted: Sun Aug 26, 2018 6:24 pm Post subject: |
|
|
Thank you!
However, maybe something is wrong in my 34 days old system, but emerge --sync returns:
| Code: | === Sync completed for gentoo
q: Updating ebuild cache for /usr/portage ...
q: Finished 35575 entries in 0.850039 seconds
Checking master signature on gentoo repo...
porthash: Using public key 09F2FF455D90CAF4
porthash: Entering /usr/portage...
porthash: Verifying existing hashfile...
porthash: Hashfile signature and format valid
porthash: Computing master hash of /usr/portage, may take some time...
porthash: error: Hashfile and computed hashes DIFFER
Killing parent process...
|
First time it was called by genup, next it was called manually. |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Sun Aug 26, 2018 6:36 pm Post subject: |
|
|
orion777,
it's my own repository check (porthash, which I rolled out before gemato was fully deployed) causing that error message. Could you please post the output of "porthash --version" and the contents of /usr/portage/repo.hash on your system (if you have a modern copy of porthash, it may have renamed this automatically to /usr/portage/local/repo.hash, to avoid clashing with gemato's checksums, so you may need to look there instead)? Thanks.
_________________
Regards,
sakaki |
|
| Back to top |
|
|
ericbish
n00b
Joined: 27 Apr 2018
Posts: 30
|
| Posted: Mon Aug 27, 2018 3:15 pm Post subject: |
|
|
| Sakaki wrote: | orion777,
it's my own repository check (porthash, which I rolled out before gemato was fully deployed) causing that error message. Could you please post the output of "porthash --version" and the contents of /usr/portage/repo.hash on your system (if you have a modern copy of porthash, it may have renamed this automatically to /usr/portage/local/repo.hash, to avoid clashing with gemato's checksums, so you may need to look there instead)? Thanks. |
I had the same problem on multiple Gentoo systems, not just this one.
https://forums.gentoo.org/viewtopic-t-1085580.html?sid=89aace0cb4eb612bf8c0f77a608e2ccc |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Mon Aug 27, 2018 3:43 pm Post subject: |
|
|
Were your other systems also arm64 using the rpi3-overlay, and/or based on gentoo-on-rpi3-64bit?
By default, the porthash repo check is only used (as far as I know) by my gated versions of the Portage tree used with the RPi3 and the Excito B2 and B3 miniservers. If you are seeing it, try deleting /usr/portage/metadata/timestamp.x and then syncing again. You can cat the /usr/portage/repo.hash on your system to see its timestamp also (this may be in /usr/portage/local/repo.hash if you are running a modern version of porthash).
_________________
Regards,
sakaki |
|
| Back to top |
|
|
ericbish
n00b
Joined: 27 Apr 2018
Posts: 30
|
| Posted: Mon Aug 27, 2018 4:13 pm Post subject: |
|
|
| Sakaki wrote: |
Were your other systems also arm64 using the rpi3-overlay, and/or based on gentoo-on-rpi3-64bit?
By default, the porthash repo check is only used (as far as I know) by my gated versions of the Portage tree used with the RPi3 and the Excito B2 and B3 miniservers. If you are seeing it, try deleting /usr/portage/metadata/timestamp.x and then syncing again. You can cat the /usr/portage/repo.hash on your system to see its timestamp also (this may be in /usr/portage/local/repo.hash if you are running a modern version of porthash). |
Nope, they were gentoo x86_64 systems, there is a thread with the same thing in the portage forum. There is a bug about it, can't remember the bug ID. I never could figure out exactly what caused it, but clearing /usr/portage and rerunning genup on your arm64 image (or emerge --sync on the x86_64 systems) cleared it up. Cutting the timestamp did not help. |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Mon Aug 27, 2018 5:42 pm Post subject: |
|
|
| ericbish wrote: |
Nope, they were gentoo x86_64 systems, there is a thread with the same thing in the portage forum. There is a bug about it, can't remember the bug ID. I never could figure out exactly what caused it, but clearing /usr/portage and rerunning genup on your arm64 image (or emerge --sync on the x86_64 systems) cleared it up. Cutting the timestamp did not help. |
That's odd. There only way that porthash gets called, afaik, is via this repo.postsync.d hook, which on the rpi3 is set up by the app-portage/rpi3-check-portage package from my rpi3-overlay. Did you copy your /usr/portage and /etc/portage directories over to an x86_64 machine by any chance, perhaps to use as a 'starter' configuration?
_________________
Regards,
sakaki |
|
| Back to top |
|
|
ericbish
n00b
Joined: 27 Apr 2018
Posts: 30
|
| Posted: Mon Aug 27, 2018 5:48 pm Post subject: |
|
|
| Sakaki wrote: | | ericbish wrote: |
Nope, they were gentoo x86_64 systems, there is a thread with the same thing in the portage forum. There is a bug about it, can't remember the bug ID. I never could figure out exactly what caused it, but clearing /usr/portage and rerunning genup on your arm64 image (or emerge --sync on the x86_64 systems) cleared it up. Cutting the timestamp did not help. |
That's odd. There only way that porthash gets called, afaik, is via this repo.postsync.d hook, which on the rpi3 is set up by the app-portage/rpi3-check-portage package from my rpi3-overlay. Did you copy your /usr/portage and /etc/portage directories over to an x86_64 machine by any chance, perhaps to use as a 'starter' configuration? |
Nope, both those other gentoo boxes were up years before I built the pi. Plus other folks have seen the issue (at least on other on the Pi, and at least a couple of others on x86_64), hence the bug report. It may be two different issues with a common similarity (the manifest failing hash) and just coincidence they came up at the same time......but either way, in both cases, reconstructing the /usr/portage directory and rerunning genup/emerge sync corrected it. |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Mon Aug 27, 2018 6:09 pm Post subject: |
|
|
ericbish,
Searching Gentoo bugzilla for porthash doesn't seem to bring up anything - did you by any chance contribute to the original bug report you mentioned? If so would you mind looking up the bug ID so I can investigate this further. Many thanks!
_________________
Regards,
sakaki |
|
| Back to top |
|
|
ericbish
n00b
Joined: 27 Apr 2018
Posts: 30
|
| Posted: Mon Aug 27, 2018 6:36 pm Post subject: |
|
|
| Sakaki wrote: | ericbish,
Searching Gentoo bugzilla for porthash doesn't seem to bring up anything - did you by any chance contribute to the original bug report you mentioned? If so would you mind looking up the bug ID so I can investigate this further. Many thanks! |
For the life of me, I cannot find it again. I came across it originally IIRC, dumping the error from one of the x86_64 boxes into google, then chasing through a ton of threads regarding the portage sync verification changes and such from a while ago. Then from there, I got sucked into the rabbit hole and somewhere among posts about manifest hash mismatches, there was a bug ID about it. About then I just threw in the towel and blew away portage, and recreated it......problem gone. |
|
| Back to top |
|
|
orion777
Apprentice
Joined: 15 Mar 2017
Posts: 207
Location: Riga, Latvia
|
| Posted: Tue Aug 28, 2018 6:01 am Post subject: |
|
|
| Sakaki wrote: | orion777,
it's my own repository check (porthash, which I rolled out before gemato was fully deployed) causing that error message. Could you please post the output of "porthash --version" and the contents of /usr/portage/repo.hash on your system (if you have a modern copy of porthash, it may have renamed this automatically to /usr/portage/local/repo.hash, to avoid clashing with gemato's checksums, so you may need to look there instead)? Thanks. |
| Code: | pi64 /usr/sbin # porthash --version
1.0.6
pi64 /usr/sbin # cat /usr/portage/repo.hash
Hash format: 1
Date: 2018-08-25 17:47
Hash: sha512sum
Metadata covered: no
5cab65371634c7824a5d4ea3685d5d5518b211d70f371ca412d7a7a99261d568d6aa535d09b9a63bc5942ed0022c3a799c61f0b979009c7d75cf4c88c2e165bb -
pi64 /usr/sbin # cat /usr/portage/local/repo.hash
Hash format: 1
Date: 2018-07-20 12:22
Hash: sha512sum
Metadata covered: no
409c1e0dd2b29b5f7af0929fa64a2970790edb5eb27a52dba5126098f7537d85ccc4a2422147909fe6dc391d9af38ef90bea2570d905ea131b84d5bf7698ff8a -
|
|
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Tue Aug 28, 2018 12:07 pm Post subject: |
|
|
orion777, ericbish (and all users of the gentoo-on-rpi3-64bit image) -
OK, first of all, an apology - there is a bug (introduced by me) in porthash-1.0.6, that in turn is causing genup to fail. I've put a fix into porthash-1.0.7, and posted a news article via the rpi3-overlay, and a GitHub issue with the resolution, also copied below. ><
Diagnostics
Look near the end of your /var/log/latest-genup-run.log file to see if the issue affects you; if it does, you'll see something similar to the below: | Code: | === Sync completed for gentoo
q: Updating ebuild cache for /usr/portage ...
q: Finished xxx entries in yyy seconds
Checking master signature on gentoo repo...
porthash: Using public key 09F2FF455D90CAF4
porthash: Entering /usr/portage...
porthash: Verifying existing hashfile...
porthash: Hashfile signature and format valid
porthash: Computing master hash of /usr/portage, may take some time...
porthash: error: Hashfile and computed hashes DIFFER
Killing parent process... |
Fixing the Issue
To address the issue, open a terminal and issue the following commands, as the root user, on your rpi3:
(if running as demouser, prefix the following commands with sudo):
| Code: | pi64 ~ # emaint sync --repo sakaki-tools
pi64 ~ # emerge --update --oneshot --verbose app-portage/porthash |
This should upgrade porthash to >= 1.0.7. Once this is done, your automatic weekly genup run should start working again.
That's it!
Background to the Issue (Optional Reading)
The porthash utility creates, or by default checks, the validity of a repository master hash (repo.hash) and counterpart digital signature (repo.hash.asc), to allow verification of a Portage tree distributed over an unauthenticated channel such as rsync. There was no such 'official' facility in Gentoo when the tool was originally deployed.
However, when Gentoo started rolling out its official app-portage/gemato manifest verification tool, porthash was modified (at v1.0.6) to migrate the location of the repo.hash{,.asc} files, from the top level /usr/portage/ directory (where they would clash with gemato) to /usr/portage/local/, which gemato ignores.
Unfortunately, during an rsync process of the Portage tree with the isshoni.org binhost, this local directory is not synced by default, but since (due to faulty logic; my bad) porthash-1.0.6 checks this location first when looking for the repo.hash{,.asc} files, the next time the tree is synced after the files have been migrated, the old (stale) /usr/portage/local/repo.hash{,.asc} files will be checked (not the fresh /usr/portage/repo.hash{,.asc} versions), and accordingly the signature verification will fail, and genup will halt with an error. (orion777 - you can see the date difference in the two repo.hash files you posted)
This error is addressed in >=porthash-1.0.7, so upgrading this single package is sufficient to fix the problem.
Thanks both for reporting this issue, and apologies again to all users for any inconvenience caused
_________________
Regards,
sakaki |
|
| Back to top |
|
|
orion777
Apprentice
Joined: 15 Mar 2017
Posts: 207
Location: Riga, Latvia
|
| Posted: Sat Sep 01, 2018 9:15 am Post subject: |
|
|
| Yes, seems working! |
|
| Back to top |
|
|
roylongbottom
n00b
Joined: 13 Feb 2017
Posts: 64
Location: Essex, UK
|
| Posted: Thu Sep 13, 2018 10:23 am Post subject: Raspberry Pi 3B+ Stress Tests |
|
|
Raspberry Pi 3B+ Stress Tests
I have finished running my benchmarks on the Raspberry Pi 3B+. A full report is available from ResearchGate:
https://www.researchgate.net/publication/327467963_Raspberry_Pi_3B_32_bit_and_64_bit_Benchmarks_and_Stress_Tests?_iepl%5BviewId%5D=RiEmnDoCO1cfHp4h46lXJY4T&_iepl%5Bcontexts%5D%5B0%5D=projectUpdatesLog&_iepl%5BtargetEntityId%5D=PB%3A327467963&_iepl%5BinteractionType%5D=publicationTitle
The last programs run were my Stress Tests that, at least, identify the 3B+ thermal characteristics. These are single core programs with input parameters for duration and test selection, with multiple copies run for maximum loading, and an updated monitor, measuring CPU MHz, temperature and core voltage. The main programs are one running integer arithmetic, another with floating point and My OpenGL program. The first exercise was with the 3B+ card installed in a plastic case, with no heatsink on the CPU.
Following is an example results from my monitoring program, whilst running four copies of the integer stress test program. These are instantaneous samples that can vary up and down within the sampling period. Above 70°C, CPU frequency is reduced from 1.4 GHz to 1.2 GHz, when core voltage is also reduced. Later thermal throttling is applied on reaching 80°C, in this case, occasionally reducing sample MHz to 1087.
| Code: |
Temperature and CPU MHz Measurement Start at Tue Jul 31 21:14:36 2018
Seconds
0.0 1400 scaling MHz, 1400 ARM MHz, core volt=1.3438V, temp=58.0°C
16.0 1400 scaling MHz, 1400 ARM MHz, core volt=1.3500V, temp=65.0°C
32.5 1400 scaling MHz, 1400 ARM MHz, core volt=1.3563V, temp=69.3°C
49.1 1400 scaling MHz, 1200 ARM MHz, core volt=1.3563V, temp=70.4°C
65.6 1400 scaling MHz, 1199 ARM MHz, core volt=1.2375V, temp=70.9°C
82.1 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=71.4°C
98.7 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=72.0°C
115.2 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=73.1°C
131.7 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=74.1°C
148.3 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=74.1°C
164.9 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=74.7°C
181.5 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=75.2°C
197.9 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=75.2°C
214.4 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=75.2°C
230.9 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=76.3°C
247.5 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=77.4°C
264.0 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=77.4°C
280.5 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=77.4°C
297.1 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=77.4°C
313.6 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=77.4°C
330.1 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=77.4°C
346.7 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=78.4°C
363.2 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=78.4°C
379.8 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=78.4°C
396.4 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
413.0 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
429.6 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
446.1 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
462.6 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
479.2 1400 scaling MHz, 1195 ARM MHz, core volt=1.2375V, temp=80.1°C
495.9 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
512.3 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
528.8 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
545.3 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
561.8 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=78.4°C
578.3 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.0°C
594.9 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=79.5°C
611.6 1400 scaling MHz, 1195 ARM MHz, core volt=1.2375V, temp=79.5°C
628.1 1400 scaling MHz, 1195 ARM MHz, core volt=1.2375V, temp=79.5°C
644.6 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=80.6°C
661.1 1400 scaling MHz, 1200 ARM MHz, core volt=1.2375V, temp=80.6°C
677.6 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.1°C
694.2 1400 scaling MHz, 1194 ARM MHz, core volt=1.2375V, temp=80.6°C
710.7 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
727.3 1400 scaling MHz, 1195 ARM MHz, core volt=1.2375V, temp=80.6°C
743.8 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
760.3 1400 scaling MHz, 1087 ARM MHz, core volt=1.2375V, temp=80.1°C
776.8 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
793.3 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
809.8 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
826.3 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=81.1°C
842.9 1400 scaling MHz, 1087 ARM MHz, core volt=1.2375V, temp=80.6°C
859.5 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
876.0 1400 scaling MHz, 1087 ARM MHz, core volt=1.2375V, temp=81.1°C
892.5 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
909.1 1400 scaling MHz, 1140 ARM MHz, core volt=1.2375V, temp=80.6°C
925.6 1400 scaling MHz, 1087 ARM MHz, core volt=1.2375V, temp=81.1°C
942.2 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=80.6°C
958.7 1400 scaling MHz, 1141 ARM MHz, core volt=1.2375V, temp=81.1°C
|
Integer Stress Tests
This has 12 tests using different data patterns, 6 of them Write/Read and 6 read only, performance being measured in MB/second. In this case, each test has the same running time, set at 80 seconds (overall 16 minutes), for this test. Below are 32 bit and 64 bit results from the 3B+, where the former is somewhat faster. There were "Cool" and "Hot" runs (room 3 °C to 4°C higher). All show CPU frequency throttling, below 1 GHz with the "Hot" tests, with similar reductions in measured performance.
| Code: | Multiply MB/second by four for overall performance
Raspbian 32 Bit Gentoo 64 Bit
Cool Hot Cool Hot
MB/s MHz °C MB/s MHz °C MB/s MHz °C MB/s MHz °C
Write/Read 1400 44.0 1400 59.1 1400 47.8 1399 65.5
1 3699 1400 68.2 3240 1200 75.2 2927 1400 69.8 2589 1200 78.4
2 3415 1200 70.9 3297 1200 79.0 2611 1200 70.9 2509 1141 81.1
3 3218 1200 72.9 3247 1195 80.6 2536 1200 72.0 2375 1087 81.7
4 3299 1200 73.1 3045 1141 81.1 2525 1200 75.2 2302 1034 81.7
5 3288 1200 75.2 2929 1087 81.7 2533 1200 75.8 2263 1034 81.7
6 3291 1200 76.3 2882 1033 81.7 2533 1200 77.4 2231 1034 81.7
Read
1 3620 1200 75.8 3343 1141 81.7 2832 1200 77.4 2646 1141 81.7
2 3602 1200 78.4 3153 1034 81.7 2841 1200 78.4 2539 1034 81.7
3 3592 1195 79.5 3015 980 82.2 2829 1195 80.1 2470 1034 81.7
4 3567 1141 80.5 2938 926 82.2 2790 1141 80.6 2444 1033 82.2
5 3500 1141 80.6 2922 980 82.7 2733 1141 80.6 2414 1034 82.2
6 3432 1087 80.6 2876 980 82.2 2679 1087 80.1 2152 980 82.2
Average 3460 1197 76.0 3074 1075 81.0 2697 1197 76.5 2411 1066 81.5
1 Core 4065 1400 4065 1400 3168 1400 3168 1400
%Av/1 Core 85 86 76 77 85 86 76 76
Start 44.0 59.1 47.8 65.5
Max 80.6 82.7 80.6 82.2
|
Floating Point Stress Tests
The program uses single precision floating point calculations, with run time options for the number of operations per data word read/written and data size, in this case, 8 operations per word and 16 KB for L1 cache use. A summary of results is below. This time, the 64 bit version is the faster (up to 17.4 GFLOPS from 4 cores). "Cool" and "Hot" test results are again provided, not particularly comparable with those for the integer tests, but suggesting slightly less performance degradation. All exceeded 70°C but the "Cool" 64 bit test did not suffer from 80°C thermal throttling.
| Code: |
Multiply MFLOPS by four for overall performance
Raspbian 32 Bit Gentoo 64 Bit
Cool Hot Cool Hot
MFLOPS MHz °C MFLOPS MHz °C MFLOPS MHz °C MFLOPS MHz °C
Average 2945 1212 75.7 2833 1168 78.7 3809 1227 71.8 3690 1203 77.4
1 Core 3439 1400 3439 1400 4360 1400 4360 1400
%Av/1 Core 86 87 82 83 87 88 85 86
Start 47.8 55.8 45.1 61.2
Max 80.1 81.7 76.3 80.1
|
OpenGL Stress Test
My OpenGL benchmark can also be included in stress testing, with a choice of window size, test function and running time. The detailed results PDF report shows that the Tiled Kitchen test produced the highest loading, along with performance being faster, using the 64 bit benchmark. Running a second 15 minute “Hot Test”, the latter, showed rapid varying speed between 20 and 18 FPS, with CPU frequency sometimes reducing to 1200, and maximum temperature of 70.9°C. VMSTAT measurements indicated that more than one CPU core was being used (average utilisation 116%).
OpenGL Extended Power Cable
After noting slow CPU benchmark performance whilst using an extended power cable, the procedure was repeated running the OpenGL test, when performance immediately reduced to 8 FPS, with the following recorded decreases in CPU MHz to 600 and core voltage to 1.2. The Pi 3B+ deserves a commendation for actually running in these circumstances (a permanent way of running cool?).
| Code: |
Seconds
0.0 1400 scaling MHz, 1400 ARM MHz, core volt=1.2000V, temp=52.6°C
1.0 1400 scaling MHz, 600 ARM MHz, core volt=1.2000V, temp=52.6°C
2.4 1400 scaling MHz, 600 ARM MHz, core volt=1.2000V, temp=52.6°C
|
OpenGL + 3 CPU Stress Tests Gentoo 64 Bit
Further 15 minute tests were carried out, running the OpenGL program at the same time as three CPU tests. Below are summaries of results, comprising a “Hot Test” using the plastic enclosure, with “Cool and Hot” using a FLIRC aluminium case, with the built in efficient CPU heat sink. “Hot” indicates a second run shortly after a “Cool” test.
Using the plastic case, 80°C thermal throttling again occurred, during both integer and floating point tests. Speeds of the latter appeared to be worse than when four copies of the program were run. Perhaps the high OpenGL CPU utilisation involved heavy use of floating point instructions.
With the FLIRC case, the CPU cores were running at 1400 MHz continuously during “Cool” sessions, the 5% per core reduction in performance being typical when running multiprocessor tests. During the “Hot” tests there was no thermal throttling, but there were instances of the 1200 MHz when 70°C was reached (not necessarily noted in instantaneous sample).
| Code: |
MB/second and MFLOPS are for each core
Integer + OpenGL
Plastic Case FLIRC Case Cool FLIRC Case Hot
MB/sec MHz FPS °C MB/sec MHz FPS °C MB/sec MHz FPS °C
Average 2376 1093 14.9 80.0 3025 1400 18.9 59.6 2954 1387 18.4 68.8
1 Core 3168 1400 20 3168 1400 20 3168 1400 20
%Av/1 Core 75 78 74 95 100 95 93 99 92
Start 55.8 37.6 53.7
Max 82.7 67.6 70.4
Floating Point + OpenGL
Plastic Case FLIRC Case Cool FLIRC Case Hot
MFLOPS MHz FPS °C MFLOPS MHz FPS °C MFLOPS MHz FPS °C
Average 2880 1137 10.5 79.8 4162 1400 18.4 64.4 4096 1393 18.8 66.8
1 Core 4360 1400 20 4360 1400 20 4360 1400 20
%Av/1 Core 66 81 53 95 100 92 94 99 94
Start 66.1 46.2 50.5
Max 82.2 69.3 69.8
|
_________________
Regards
Roy |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Thu Sep 13, 2018 11:10 am Post subject: |
|
|
roylongbottom,
as always, very interesting results. One question - are the integer stress tests moving 32-bit ints around? If so, do you have a version of the same test that moves 64-bit ints? Unaligned data access (wrt the native word length) would probably impose some performance penalty, as appears to be the case here for 64-bit vs 32-bit mode.
_________________
Regards,
sakaki |
|
| Back to top |
|
|
roylongbottom
n00b
Joined: 13 Feb 2017
Posts: 64
Location: Essex, UK
|
| Posted: Thu Sep 13, 2018 3:51 pm Post subject: |
|
|
| Sakaki wrote: | roylongbottom,
as always, very interesting results. One question - are the integer stress tests moving 32-bit ints around? If so, do you have a version of the same test that moves 64-bit ints? Unaligned data access (wrt the native word length) would probably impose some performance penalty, as appears to be the case here for 64-bit vs 32-bit mode. |
I have a 64 bit integer version for Linux/PCs. I will see if it is easily convertible.
_________________
Regards
Roy |
|
| Back to top |
|
|
roylongbottom
n00b
Joined: 13 Feb 2017
Posts: 64
Location: Essex, UK
|
| Posted: Sat Sep 15, 2018 11:28 am Post subject: |
|
|
Sakaki
I have converted the program that uses 64 bit integers and believe that it measures performance accurately. (It used assembly code for PC versions). It was compiled using gcc 7. I also recompiled the 32 bit integer program and confirmed that results were essentially the same as the original, from gcc 6. Following are results of 5 second tests at KB sizes 16, 64 and 2046 to use L1 cache, L2 cache and RAM.
CPUs use the same registers and equivalent instructions for 64 bit and 32 bit scalar integer arithmetic (confirmed with disassembly) and can execute them at the same speed, where 64 bit MB/second data transfer speed would be double that using 32 bit numbers. This is best demonstrated in read only access using L1 cache based data. As the measurements become more dependent on data transfer speed, 64 bit arithmetic can be at half speed, or same MB/second, as in the read only from RAM example. There are other considerations where writing to memory is involved.
| Code: | Integer Stresss Test Single Core MB/second
Write/Read Read
L1 L2 RAM L1 L2 RAM
32 Bit Integers 2989 2916 1524 3348 2866 1862
64 Bit Integers 5706 4635 1094 6650 5323 1945
|
If the programs had complied to use vector instructions, execution speed, using 32 bit numbers, would be twice that with 64 bit data.
_________________
Regards
Roy |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Wed Sep 26, 2018 7:10 pm Post subject: |
|
|
Hello,
I've just posted a v1.3.0 release of my bootable 64-bit Gentoo image for the RPi3 (model B and B+) on GitHub (here, includes full download instructions).
A changelog from the prior release image (with upgrade instructions) may be viewed here, but in summary:- Migrated from porthash repository verification to Gentoo's own, official gemato-based approach (with failure quarantine). Accordingly, the porthash USE flag on dev-embedded/rpi3-64bit-meta has switched from default-on to default-off as of v1.3.0, and the weekly-gated rsync URI has changed (to one without polluting porthash signatures), from rsync://isshoni.org/gentoo-portage-pi64 to rsync://isshoni.org/gentoo-portage-pi64-gem. (The older version will continue to be supported for a time, for backwards compatibility during the changeover period.)
- Added support for the transparent-compression write-through zswap cache to bcmrpi3-kernel-bis, and created a startup service (rpi3-zswap) to start using it. Given the highly compressible nature of most RAM pages on a running system, and the RPi3's relatively meagre I/O capabilities, this should materially improve system responsiveness under load. Parameterized via /etc/conf.d/rpi3-zswap.
- Added a startup service (rpi3-expand-swap), to increase the ('real', backing-store-based) swapfile size to 1GiB, space permitting, as a one-off operation post root partition and filesystem resize. Parametrized via /etc/conf.d/rpi3-expand-swap.
- Various minor ebuild tidy-ups.
- All packages brought up-to-date against the Gentoo tree, as of 16 September 2018. Most packages have been rebuilt on gcc-8.2 (which should bring a small performance improvement).
- Kernel upgraded to sys-kernel/bcmrpi3-kernel-bis-bin-4.14.71.20180922, accompanying boot firmware to sys-boot/rpi3-64bit-firmware-1.20180919 (these will of course auto-update as new versions are unmasked).
A variant image for the Pi-Top v1 (an RPi3-based DIY laptop) is also included.
Have fun ^-^
And, as always, any problems or comments, please post in this thread!
_________________
Regards,
sakaki |
|
| Back to top |
|
|
orion777
Apprentice
Joined: 15 Mar 2017
Posts: 207
Location: Riga, Latvia
|
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Thu Oct 04, 2018 3:23 pm Post subject: |
|
|
Hello,
as the current gentoo-on-rpi3-64bit image (for the RPi3 B/B+) has KVM enabled in the kernel, I thought it might be worth briefly covering how to use it to efficiently run another OS as a virtualized QEMU guest.
For the sake of concreteness, I'll show how to start up the following (obviously, you can adapt for your particular interests):- hardware: RPi3 (B or B+);
- 'host' OS: >= v1.3.0 of my bootable gentoo-on-rpi3-64bit image;
- 'guest' OS: the latest official 64-bit aarch64 cloud image of Ubuntu Server 18.04 LTS ('bionic beaver') (cloud images are deliberately minimal, so well suited for our needs);
- virtualizer: app-emulation/qemu-3.0.0
- BIOS: tianocore aarch64 EFI;
- cores: 2 out of the 4 available;
- memory: 256 MiB memory allocation (from the RPi3's 1GiB);
- console-only setup, no graphics, SPICE etc. (easy to add if you want);
- pass-through networking enabled (so you can apt-get from the guest, etc.);
- cloud-init 'NoCloud' data source set up, to provide the initial machine name, ubuntu user's password etc.
- running as the regular user ('demouser'), not root.
Begin with your gentoo-on-rpi3-64bit system booted to the graphical desktop, with network connectivity established.
Then, open a terminal, and working as the regular user ('demouser'), issue:
| Code: |
demouser@pi64 ~ $ mkdir -p qemu-test && cd qemu-test
|
Next, collect the various pieces of software needed to boot the guest. The first is an EFI BIOS. Here, we'll use the latest aarch64 (aka arm64) tianocore image from Linaro. Issue:
| Code: |
demouser@pi64 ~/qemu-test $ wget -c http://snapshots.linaro.org/components/kernel/leg-virt-tianocore-edk2-upstream/latest/QEMU-AARCH64/RELEASE_CLANG35/QEMU_EFI.fd |
The firmware image is 2MiB so shouldn't take long to download.
Note that for simplicity, we'll not set up the ability for persistent EFI variables in this demo (see here for instructions on how to do so).
Next, download the latest Ubuntu 'bionic' (18.04 LTS server) arm64 cloud image. Issue:
| Code: |
demouser@pi64 ~/qemu-test $ wget -c https://cloud-images.ubuntu.com/bionic/current/bionic-server-cloudimg-arm64.img
|
You can of course use a different OS or version if you like. The exact size of this image will depend upon what is 'current' when you try it, of course, but at the time of writing it was ~300MiB, so the above download may take a little time, depending on the speed of your network connection.
Note that although the image is already in QEMU QCOW2 format, we won't use it for booting directly, as we may want to start various fresh instances (and the copy we boot will be modified once used, since it encapsulates a writeable root filesystem). Instead, we'll make a copy, using this image as the basis. The gentoo-on-rpi3-64bit image already contains app-emulation/qemu pre-installed, so issue:
| Code: |
demouser@pi64 ~/qemu-test $ qemu-img create -f qcow2 -b bionic-server-cloudimg-arm64.img bionic-image-01.img
|
to create a derivative 'instance' QCOW2 image (bionic-image-01.img), backed by the 'master' copy you just downloaded. (you can do this as many times as you like).
Now, as is now common with such 'cloud' images (not just from Ubuntu), no 'out of the box' login credentials, hostname etc. are configured. The chicken-and-egg problem this obviously creates is solved through the use of the cloud-init service (pre set-up to run on boot). Inter alia, this will look for configuration data stored in a specially named (viz.: 'cidata') iso9660 filesystem, and if found uses it to set up initial passwords and so forth.
Following these notes, we'll just create a bare-minimum 'NoCloud' data source here. Issue:
| Code: |
demouser@pi64 ~/qemu-test $ { echo instance-id: kvm-bionic-01; echo local-hostname: kvm-bionic; } > meta-data
demouser@pi64 ~/qemu-test $ printf "#cloud-config\npassword: passw0rd\nchpasswd: { expire: False }\nssh_pwauth: True\n" > user-data
|
If you run "tail -n +1 *-data", you should now see:
| Code: | ==> meta-data <==
instance-id: kvm-bionic-01
local-hostname: kvm-bionic
==> user-data <==
#cloud-config
password: passw0rd
chpasswd: { expire: False }
ssh_pwauth: True
|
These two files (when suitably packaged) will instruct cloud-init to:- Set up an instance called kvm-bionic--01, with hostname kvm-bionic
- Set the password for the 'ubuntu' (default) user to passw0rd (adapt if desired), ensure it has no expiry, and allow it to be used for login via ssh.
More sophisticated configs are possible of course (setting up public keys for ssh login etc.) but this isn't a tutorial on cloud-init, so we won't use them ^-^
Next, to be able to package the config data, we need a utility called mkisofs; this is part of the app-cdr/cdrtools package (covered by virtual/cdrtools), which is not shipped with the gentoo-on-rpi3-64bit image by default, but is available on the binhost. So to install it, issue:
| Code: |
demouser@pi64 ~/qemu-test $ sudo emerge --verbose --noreplace virtual/cdrtools
|
This shouldn't take long to complete. Once done, you can proceed to build the specially named iso9660 image; issue:
| Code: |
demouser@pi64 ~/qemu-test $ mkisofs -o seed-kvm-bionic-01.iso -V cidata -J -rock user-data meta-data
|
Hint: on some distributions (although not Gentoo, yet) mkisofs has been replaced by genisoimage, which has a slightly different invocation syntax.
If you run "ls" in your qemu-test directory, you should now see:
| Code: | QEMU_EFI.fd bionic-server-cloudimg-arm64.img seed-kvm-bionic-01.iso
bionic-image-01.img meta-data user-data |
That's the preparation over, we can now boot the image! Make sure your RPi3 isn't too heavily loaded, then run (still as the regular user, in the qemu-test directory):
| Code: |
demouser@pi64 ~/qemu-test $ qemu-system-aarch64 -M virt -cpu host \
-m 256M -smp 2 -nographic \
-bios QEMU_EFI.fd \
-cdrom seed-kvm-bionic-01.iso \
-drive if=none,file=bionic-image-01.img,id=hd0 -device virtio-blk-device,drive=hd0 \
-device virtio-net-device,netdev=vmnic -netdev user,id=vmnic \
-accel kvm 2>/dev/null
|
Most of these options should be self explanatory (see the qemu docs for more details). Note in particular that we:
- allocate 256MiB of memory and restrict to two processors, no graphics (second line); and
- turn on KVM acceleration (last line) and specify the 'host' cpu type (which requires it; first line).
If you see a grub boot screen displayed, just press Enter to continue. A small number of error messages may also be shown, but after a few seconds the bionic image should start booting; you will see its kernel output followed by standard systemd traces, printed to the same console window in which you issued the above qemu-system-aarch64 call.
Shortly thereafter, if all is well, you should be greeted by a login prompt. Log in as user ubuntu, password passw0rd.
Once in, you can then play around with your Ubuntu system! Here's a screenshot from one of my RPi3B+'s:
https://raw.githubusercontent.com/sakaki-/resources/master/raspberrypi/pi3/kvm-demo-screenshot.png
Note how the Gentoo (top console) and Ubuntu (bottom console) instances in the above screenshot are running different kernels - this is not simply a chroot. And also that the system load is very low, due to the efficiency of the kvm virtualization.
One point: with networking set up as here, you can't ping from inside the guest system, but you can wget etc., and so apt-get works. This networking issue can easily be resolved, but this isn't a detailed qemu tutuorial.
On the text console, you can use Ctrl-a then c to switch between the bash prompt and the qemu monitor prompt (e.g. see the top of the lower console window in the above screenshot).
have fun ^-^
PS: the current kernel config may be viewed here, diff against the bcmrpi3_defconfig here.
_________________
Regards,
sakaki |
|
| Back to top |
|
|
Sakaki
Guru
Joined: 21 May 2014
Posts: 409
|
| Posted: Tue Nov 06, 2018 4:52 pm Post subject: |
|
|
FYI, firefox-63.0.1-r1 is now available on the binhost. This required a bit of tweaking to build with bindist set, but hopefully will work OK. Please let me know if you experience any problems with it.
As before, users on the latest v1.3.0 gentoo-on-rpi3-64bit image just need to run genup (as root, or using sudo) to get the updated browser via binary package - or, if you prefer, simply wait for the system's weekly autoupdate to do this for you.
(If you have a significant amount of work invested in an older release of this image, I have also provided manual upgrade instructions (from 1.0.0 thru 1.2.2 → 1.3.0) here.)
_________________
Regards,
sakaki |
|
| Back to top |
|
|
Irre
Guru
Joined: 09 Nov 2013
Posts: 434
Location: Stockholm
|
| Posted: Tue Nov 13, 2018 7:37 pm Post subject: rpi3 display problems |
|
|
I installed the image to a 16g sd-card.
Boot was successful and wireless keyboard and mouse worked perfectly -- some minutes. Then the monitor complained: "HDMI1 no signal" and all went black!
After reboots it works again some minute. Some time I can use the monitor as a console. But the screen disappears over and over again. 
Login via SSH works fine.
The same HDMI-cable and Monitor work perfectly with an old Raspberry.
What is wrong? The sd-card is rather slow, 1 GIB is written in about 60 s. I also suspect hardware error in the rpi3. It is new.
The power supply is "Raspberry" original, so I think power is OK.
I am trying to update the system with "genup". There are some error messages: | Code: | ...
* Syncing all portage overlays
/usr/bin/eix-sync: line 396: layman: command not found
* layman -S failed
...
>>> No outdated packages were found on your system.
* Updating @world set (for new versions, or changed use flags)...
Draw call returned Invalid argument. Expect corruption.
...
|
When I rerun "genup" it hangs, I think. | Code: | >>> No outdated packages were found on your system.
* Updating @world set (for new versions, or changed use flags)...
top command:
8922 root 39 19 373976 363172 4268 R 100.0 36.6 13:17.39 emerge |
I gave up after waiting more than an hour for emerge to complete. /var/log/emerge.log shows nothing: | Code: | 1542136327: *** Finished. Cleaning up...
1542136332: *** exiting successfully.
1542136332: *** terminating.
|
Edit: I see that it is lack of memory. I add a swapfile and rerun over night! | Code: | [16103.027259] SLUB: Unable to allocate memory on node -1, gfp=0x14000c0(GFP_KERNEL)
[16103.027265] cache: nsproxy, object size: 56, buffer size: 56, default order: 0, min order: 0
[16103.027272] node 0: slabs: 2175, objs: 158775, free: 0
[16103.027295] kswapd0: page allocation failure: order:0, mode:0x14000c0(GFP_KERNEL), nodemask=(null)
[16103.027310] kswapd0 cpuset=/ mems_allowed=0
[16103.027324] CPU: 0 PID: 45 Comm: kswapd0 Tainted: G D C 4.14.71-v8-4f30a5365296-bis+ #2
[16103.027331] Hardware name: Raspberry Pi 3 Model B Plus Rev 1.3 (DT)
[16103.027336] Call trace:
[16103.027346] [<ffffff9be8e8b1e8>] dump_backtrace+0x0/0x268
[16103.027354] [<ffffff9be8e8b474>] show_stack+0x24/0x30
[16103.027361] [<ffffff9be9572ecc>] dump_stack+0xac/0xe8
[16103.027368] [<ffffff9be8fe2ae8>] warn_alloc+0xe0/0x160
[16103.027376] [<ffffff9be8fe3a90>] __alloc_pages_nodemask+0xe90/0xec8
[16103.027383] [<ffffff9be9035e24>] new_slab+0x404/0x578
[16103.027391] [<ffffff9be9038210>] ___slab_alloc.constprop.30+0x2d0/0x368
[16103.027398] [<ffffff9be9038304>] __slab_alloc.isra.24.constprop.29+0x5c/0xa8
[16103.027406] [<ffffff9be9038590>] kmem_cache_alloc+0x240/0x270
[16103.027414] [<ffffff9be9031d9c>] zswap_frontswap_store+0xbc/0x620
[16103.027422] [<ffffff9be90304ec>] __frontswap_store+0x9c/0x170
[16103.027429] [<ffffff9be9029aa0>] swap_writepage+0x68/0xc0
[16103.027437] [<ffffff9be8ff0adc>] pageout.isra.19+0x1a4/0x330
[16103.027444] [<ffffff9be8ff2cec>] shrink_page_list+0x7fc/0xaf8
[16103.027451] [<ffffff9be8ff36e4>] shrink_inactive_list+0x20c/0x5f0
[16103.027459] [<ffffff9be8ff4250>] shrink_node_memcg+0x368/0x640
[16103.027466] [<ffffff9be8ff45ec>] shrink_node+0xc4/0x328
[16103.027473] [<ffffff9be8ff5548>] kswapd+0x2b8/0x7f8
[16103.027481] [<ffffff9be8eee788>] kthread+0x108/0x138
[16103.027488] [<ffffff9be8e85248>] ret_from_fork+0x10/0x18
|
Last edited by Irre on Tue Nov 13, 2018 10:38 pm; edited 1 time in total |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Gentoo on ARM
