| View previous topic :: View next topic |
| Author |
Message |
soustan
n00b
Joined: 12 Apr 2020
Posts: 4
|
 Posted: Fri Jan 17, 2025 5:34 pm Post subject: I can't format the disk partitions before installing Gentoo |
 |
|
Good day, Everyone!
I can't format the disk partitions before installing Gentoo OS.
During the installation of Gentoo OS, it is necessary to format the hard disk partitions.
The system is installed on a separate disk (SSD) ---> /dev/sdb.
#fdisk /dev/sdb
Debian12 OS(/dev/sda) is also installed on this computer.
#fdisk /dev/sda
I am trying to format a partition (SSD) ---> /dev/sdb1 into a FAT32 file system.
However, the following error occurs.
| Code: | #mkfs.vfat -F 32 /dev/sdb1
mkfs.fat 4.2 (2021-01-31)
mkfs.vfat: unable to open /dev/sdb1: Device or resource busy
|
# mount
Please tell me where I am wrong? How do I format the sections correctly?
Fixed pastbin link -- NeddySeagoon - twice ... and again
... and code tags |
|
| Back to top |
|
 |
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54725
Location: 56N 3W
|
| Posted: Fri Jan 17, 2025 5:49 pm Post subject: |
|
|
soustan,
| Code: | # fdisk /dev/sdb
Welcome to fdisk (util-linux 2.40.2).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
This disk is currently in use - repartitioning is probably a bad idea.
It's recommended to umount all file systems, and swapoff all swap
partitions on this disk. |
That suggests that part of /dev/sdb is in use.
| Code: | | unable to open /dev/sdb1: Device or resource busy |
says that sdb1 exists but is being used by something else.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
soustan
n00b
Joined: 12 Apr 2020
Posts: 4
|
| Posted: Fri Jan 17, 2025 6:04 pm Post subject: |
|
|
NeddySeagoon,
I understand that the ssd drive is busy with something. However, the output of the #mount ,
command is he doesn't write anything about it.
How to understand this and how to find out what /dev/sdb is doing? |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54725
Location: 56N 3W
|
| Posted: Fri Jan 17, 2025 6:18 pm Post subject: |
|
|
soustan,
Try a reboot. After you have made changes with fdisk, the syncing are rereading partiton tables does not always work.
A restart forces the kernel to read the partition tables again.
Beware that kernel device names are not deterministic. They are allocated in device discovery order which can change from boot to boot.
Take care that you make your filesystems on the right device.
Use to check.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
soustan
n00b
Joined: 12 Apr 2020
Posts: 4
|
| Posted: Fri Jan 17, 2025 6:33 pm Post subject: |
|
|
NeddySeagoon,
Output of the #fdisk -l command.
The fact is that after restarting the computer, nothing in the sense that the disk partition /dev/sda1 does not change. And he's still busy.
Maybe some other command output is needed?
GPT PMBR size mismatch (7465131 != 15820799) will be corrected by write.
The backup GPT table is not on the end of the device.
Perhaps it's all about this recording?
However, I cannot understand what "will be corrected by write" means??
I have already written down the partition table by specifying the "w" symbol. Or is there something else that needs to be done? |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54725
Location: 56N 3W
|
| Posted: Fri Jan 17, 2025 7:03 pm Post subject: |
|
|
soustan,
| Code: | GPT PMBR size mismatch (7465131 != 15820799) will be corrected by write.
The backup GPT table is not on the end of the device. |
The Primary Master Boot Record (PMBR) the partition table, does not match the size of the device. Hence, 7465131 != 15820799.
I don't see where either of those numbers come from.
There is a secondary boot record, which is supposed to be at the end of the device but | Code: | | The backup GPT table is not on the end of the device |
says that its in the wrong place.
Both problems | Code: | | will be corrected by write. |
That makes me nervous. If there is nothing on your
| Code: | Disk /dev/sdb: 1.86 TiB, 2048408248320 bytes, 4000797360 sectors
Disk model: SSD 2TB |
yet, I would make a new partition table on it and start from there.
If you move the backup partition table, you don't know what's in the space where it will be moved to.
It should be outside of any partition but your last partition ends at sector 4000796671, which looks about right for a 4000797360 sector volume.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
|
Installing Gentoo
