| View previous topic :: View next topic |
| Author |
Message |
rino88
n00b
Joined: 02 Apr 2015
Posts: 5
|
 Posted: Thu Apr 02, 2015 10:51 am Post subject: Hyper-V kernel panic |
 |
|
Установил gentoo на HYPER-V сервер. После настройки по хэндбуку и перезагрузки кернел яро паникует.
Ошибка:
| Quote: | | Kernel panic - not syncing: VFS: Unable to mount root fs on unknown block(8,4) |
Пробовал подключать старые ATA драйвера - в ошибки сменился адрес диска на (0,0)
/etc/fstab
| Code: |
/dev/sda2 /boot ext2 default,noatime 0 2
/dev/sda4 / ext4 noatime 0 1
/dev/sda3 none /swap sw 0 0
/dev/cdrom /mnt/cdrom /auto noatime, ro 0 0
|
Помогите решить |
|
| Back to top |
|
 |
TigerJr
Guru
Joined: 19 Jun 2007
Posts: 540
|
| Posted: Fri Apr 03, 2015 11:24 pm Post subject: |
|
|
| Quote: | | Пробовал подключать старые ATA драйвера - в ошибки сменился адрес диска на (0,0) |
это значит ядро вообще разделов не увидело.
Телепатически(как обычно) пытаюсь догадаться что в первом случае было лучше.
_________________
Do not use gentoo, it die |
|
| Back to top |
|
|
rino88
n00b
Joined: 02 Apr 2015
Posts: 5
|
| Posted: Mon Apr 06, 2015 3:51 am Post subject: |
|
|
| Какие данные еще добавить? |
|
| Back to top |
|
|
TigerJr
Guru
Joined: 19 Jun 2007
Posts: 540
|
| Posted: Wed Apr 08, 2015 7:12 pm Post subject: |
|
|
неплохо бы dmesg глянуть в первом случае, как я понял. Ну и конфиг(.config) ядра и вывод lspci -k с установочного образа.
Ну и не самый важный вопрос, таблица разделов GPT или DOS?
_________________
Do not use gentoo, it die |
|
| Back to top |
|
|
rino88
n00b
Joined: 02 Apr 2015
Posts: 5
|
| Posted: Wed Apr 15, 2015 6:52 am Post subject: |
|
|
lspci -k
| Code: | 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 03)
00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01)
Subsystem: Microsoft Corporation Device 0000
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
Kernel driver in use: ata_piix
Kernel modules: ata_piix, pata_acpi, ata_generic
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:08.0 VGA compatible controller: Microsoft Corporation Hyper-V virtual VGA |
dmesg
| Code: | [ 0.000000] Linux version 3.18.9-gentoo (root@nightheron) (gcc version 4.8.3 (Gentoo 4.8.3 p1.1, pie-0.5.9) ) #1 SMP Thu Mar 26 06:34:51 UTC 2015
[ 0.000000] Command line: root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroot initrd=gentoo.igz vga=791 BOOT_IMAGE=gentoo
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000f7feffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000f7ff0000-0x00000000f7ffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000f7fff000-0x00000000f7ffffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000107ffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090004 03/19/2009
[ 0.000000] Hypervisor detected: Microsoft HyperV
[ 0.000000] HyperV: features 0x67f, hints 0x2c
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x108000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-back
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF00000000 write-back
[ 0.000000] 1 base 0100000000 mask FFF0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0xf7ff0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x019f3000, 0x019f3fff] PGTABLE
[ 0.000000] BRK [0x019f4000, 0x019f4fff] PGTABLE
[ 0.000000] BRK [0x019f5000, 0x019f5fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x107e00000-0x107ffffff]
[ 0.000000] [mem 0x107e00000-0x107ffffff] page 2M
[ 0.000000] BRK [0x019f6000, 0x019f6fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x104000000-0x107dfffff]
[ 0.000000] [mem 0x104000000-0x107dfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x103ffffff]
[ 0.000000] [mem 0x100000000-0x103ffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x80000000-0xf7feffff]
[ 0.000000] [mem 0x80000000-0xf7dfffff] page 2M
[ 0.000000] [mem 0xf7e00000-0xf7feffff] page 4k
[ 0.000000] BRK [0x019f7000, 0x019f7fff] PGTABLE
[ 0.000000] BRK [0x019f8000, 0x019f8fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x7fffffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x7fffffff] page 2M
[ 0.000000] RAMDISK: [mem 0x7fbeb000-0x7fffefff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F5210 000014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 0x00000000F7FF0000 000040 (v01 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: FACP 0x00000000F7FF0200 000081 (v02 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: DSDT 0x00000000F7FF0DA4 00217C (v01 MSFTVM MSFTVM02 00000002 INTL 02002026)
[ 0.000000] ACPI: FACS 0x00000000F7FFF000 000040
[ 0.000000] ACPI: WAET 0x00000000F7FF0B00 000028 (v01 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: SLIC 0x00000000F7FF0B40 000176 (v01 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: OEM0 0x00000000F7FF0D40 000064 (v01 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: SRAT 0x00000000F7FF0600 0004C0 (v02 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: APIC 0x00000000F7FF0300 000244 (v01 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: OEMB 0x00000000F7FFF240 000053 (v01 VRTUAL MICROSFT 03000919 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] [ffffea0000000000-ffffea00039fffff] PMD -> [ffff880103600000-ffff880106ffffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x107ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xf7feffff]
[ 0.000000] node 0: [mem 0x100000000-0x107ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00001000-0x107ffffff]
[ 0.000000] On node 0 totalpages: 1048462
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 1011696 pages, LIFO batch:31
[ 0.000000] Normal zone: 448 pages used for memmap
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x08] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x09] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0a] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0b] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0c] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0d] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0e] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x0f] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x11] lapic_id[0x10] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x12] lapic_id[0x11] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x13] lapic_id[0x12] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x14] lapic_id[0x13] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x15] lapic_id[0x14] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x16] lapic_id[0x15] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x17] lapic_id[0x16] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x18] lapic_id[0x17] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x19] lapic_id[0x18] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1a] lapic_id[0x19] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1b] lapic_id[0x1a] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1c] lapic_id[0x1b] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1d] lapic_id[0x1c] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1e] lapic_id[0x1d] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1f] lapic_id[0x1e] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x20] lapic_id[0x1f] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x21] lapic_id[0x20] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x22] lapic_id[0x21] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x23] lapic_id[0x22] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x24] lapic_id[0x23] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x25] lapic_id[0x24] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x26] lapic_id[0x25] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x27] lapic_id[0x26] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x28] lapic_id[0x27] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x29] lapic_id[0x28] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x2a] lapic_id[0x29] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x2b] lapic_id[0x2a] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x2c] lapic_id[0x2b] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x2d] lapic_id[0x2c] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x2e] lapic_id[0x2d] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x2f] lapic_id[0x2e] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x30] lapic_id[0x2f] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x31] lapic_id[0x30] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x32] lapic_id[0x31] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x33] lapic_id[0x32] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x34] lapic_id[0x33] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x35] lapic_id[0x34] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x36] lapic_id[0x35] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x37] lapic_id[0x36] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x38] lapic_id[0x37] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x39] lapic_id[0x38] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x3a] lapic_id[0x39] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x3b] lapic_id[0x3a] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x3c] lapic_id[0x3b] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x3d] lapic_id[0x3c] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x3e] lapic_id[0x3d] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x3f] lapic_id[0x3e] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 63 CPUs, 62 hotplug CPUs
[ 0.000000] e820: [mem 0xf8000000-0xfffbffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:63 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff880102e00000 s72960 r8192 d29440 u131072
[ 0.000000] pcpu-alloc: s72960 r8192 d29440 u131072 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
[ 0.000000] pcpu-alloc: [0] 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
[ 0.000000] pcpu-alloc: [0] 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
[ 0.000000] pcpu-alloc: [0] 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 --
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1033657
[ 0.000000] Kernel command line: root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroot initrd=gentoo.igz vga=791 BOOT_IMAGE=gentoo
[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 253952 bytes
[ 0.000000] log_buf_len min size: 262144 bytes
[ 0.000000] log_buf_len: 524288 bytes
[ 0.000000] early log buf free: 250252(95%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Memory: 4040404K/4193848K available (4643K kernel code, 450K rwdata, 1660K rodata, 876K init, 636K bss, 153444K reserved)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=63.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=63
[ 0.000000] NR_IRQS:4352 nr_irqs:928 0
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.000000] tsc: Unable to calibrate against PIT
[ 0.000000] tsc: using PMTIMER reference calibration
[ 0.000000] tsc: Detected 2399.481 MHz processor
[ 0.030021] Calibrating delay loop (skipped), value calculated using timer frequency.. 4798.96 BogoMIPS (lpj=23994810)
[ 0.030029] pid_max: default: 64512 minimum: 504
[ 0.030066] ACPI: Core revision 20140926
[ 0.045250] ACPI: All ACPI Tables successfully acquired
[ 0.045560] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.045566] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.048419] CPU: Physical Processor ID: 0
[ 0.048424] CPU: Processor Core ID: 0
[ 0.048428] mce: CPU supports 0 MCE banks
[ 0.048462] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.064718] Switched APIC routing to physical flat.
[ 0.103842] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.103848] smpboot: CPU0: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz (fam: 06, model: 2c, stepping: 02)
[ 0.110000] Performance Events: unsupported p6 CPU model 44 no PMU driver, software events only.
[ 0.110000] x86: Booted up 1 node, 1 CPUs
[ 0.110000] smpboot: Total of 1 processors activated (4798.96 BogoMIPS)
[ 0.110000] devtmpfs: initialized
[ 0.110309] NET: Registered protocol family 16
[ 0.110482] cpuidle: using governor ladder
[ 0.110487] cpuidle: using governor menu
[ 0.110604] ACPI: bus type PCI registered
[ 0.110730] dca service started, version 1.12.1
[ 0.111082] PCI: Using configuration type 1 for base access
[ 0.113099] ACPI: Added _OSI(Module Device)
[ 0.113103] ACPI: Added _OSI(Processor Device)
[ 0.113106] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.113108] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.118234] ACPI: Interpreter enabled
[ 0.118244] ACPI: (supports S0 S5)
[ 0.118246] ACPI: Using IOAPIC for interrupt routing
[ 0.118310] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.122833] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.122843] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[ 0.122852] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.122963] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.122998] PCI host bridge to bus 0000:00
[ 0.123003] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.123008] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.123012] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.123016] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.123021] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfffbffff]
[ 0.123190] pci 0000:00:00.0: [8086:7192] type 00 class 0x060000
[ 0.125185] pci 0000:00:07.0: [8086:7110] type 00 class 0x060100
[ 0.127706] pci 0000:00:07.1: [8086:7111] type 00 class 0x010180
[ 0.129756] pci 0000:00:07.1: reg 0x20: [io 0xffa0-0xffaf]
[ 0.130654] pci 0000:00:07.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.130660] pci 0000:00:07.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.130664] pci 0000:00:07.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.130668] pci 0000:00:07.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.131239] pci 0000:00:07.3: [8086:7113] type 00 class 0x068000
[ 0.131279] * Found PM-Timer Bug on the chipset. Due to workarounds for a bug,
* this clock source is slow. Consider trying other clock sources
[ 0.133578] pci 0000:00:07.3: quirk: [io 0x0400-0x043f] claimed by PIIX4 ACPI
[ 0.134499] pci 0000:00:08.0: [1414:5353] type 00 class 0x030000
[ 0.143089] pci 0000:00:08.0: reg 0x10: [mem 0xf8000000-0xfbffffff]
[ 0.146225] pci_bus 0000:00: on NUMA node 0
[ 0.151489] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.151869] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.152123] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.152381] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.152683] vgaarb: setting as boot device: PCI:0000:00:08.0
[ 0.152689] vgaarb: device added: PCI:0000:00:08.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.152692] vgaarb: loaded
[ 0.152695] vgaarb: bridge control possible 0000:00:08.0
[ 0.152816] SCSI subsystem initialized
[ 0.152822] ACPI: bus type USB registered
[ 0.152854] usbcore: registered new interface driver usbfs
[ 0.152870] usbcore: registered new interface driver hub
[ 0.152914] usbcore: registered new device driver usb
[ 0.153049] PCI: Using ACPI for IRQ routing
[ 0.153054] PCI: pci_cache_line_size set to 64 bytes
[ 0.153473] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.153476] e820: reserve RAM buffer [mem 0xf7ff0000-0xf7ffffff]
[ 0.153751] Switched to clocksource hyperv_clocksource
[ 0.155505] pnp: PnP ACPI init
[ 0.156147] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.157384] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.158018] pnp 00:02: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[ 0.159250] pnp 00:03: [dma 0 disabled]
[ 0.159293] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.159293] pnp 00:04: [dma 0 disabled]
[ 0.159293] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.159293] pnp 00:05: [dma 2]
[ 0.159293] pnp 00:05: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.159293] system 00:06: [io 0x01e0-0x01ef] has been reserved
[ 0.159293] system 00:06: [io 0x0160-0x016f] has been reserved
[ 0.159293] system 00:06: [io 0x0278-0x027f] has been reserved
[ 0.159293] system 00:06: [io 0x0378-0x037f] has been reserved
[ 0.159293] system 00:06: [io 0x0678-0x067f] has been reserved
[ 0.159293] system 00:06: [io 0x0778-0x077f] has been reserved
[ 0.159293] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.159293] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.159293] system 00:07: [io 0x0400-0x043f] has been reserved
[ 0.159293] system 00:07: [io 0x0370-0x0371] has been reserved
[ 0.159293] system 00:07: [io 0x0440-0x044f] has been reserved
[ 0.159293] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.159293] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.159293] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.159293] system 00:08: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.159293] system 00:08: [mem 0x000c0000-0x000dffff] could not be reserved
[ 0.159293] system 00:08: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.159293] system 00:08: [mem 0x00100000-0xf7ffffff] could not be reserved
[ 0.159293] system 00:08: [mem 0xfffc0000-0xffffffff] has been reserved
[ 0.159293] system 00:08: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.159293] pnp: PnP ACPI: found 9 devices
[ 0.163849] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.163852] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.163855] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.163857] pci_bus 0000:00: resource 7 [mem 0xf8000000-0xfffbffff]
[ 0.163937] NET: Registered protocol family 2
[ 0.164380] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.164479] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.164588] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.164619] TCP: reno registered
[ 0.164634] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.164655] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.164908] NET: Registered protocol family 1
[ 0.165118] RPC: Registered named UNIX socket transport module.
[ 0.165123] RPC: Registered udp transport module.
[ 0.165125] RPC: Registered tcp transport module.
[ 0.165128] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.165139] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 0.165877] pci 0000:00:08.0: Video device with shadowed ROM
[ 0.165926] PCI: CLS 0 bytes, default 64
[ 0.166063] Trying to unpack rootfs image as initramfs...
[ 0.893312] Freeing initrd memory: 4176K (ffff88007fbeb000 - ffff88007ffff000)
[ 0.893325] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.893329] software IO TLB [mem 0xf3ff0000-0xf7ff0000] (64MB) mapped at [ffff8800f3ff0000-ffff8800f7feffff]
[ 0.894122] futex hash table entries: 16384 (order: 8, 1048576 bytes)
[ 0.894728] VFS: Disk quotas dquot_6.5.2
[ 0.894787] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.895084] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.895451] NFS: Registering the id_resolver key type
[ 0.895461] Key type id_resolver registered
[ 0.895462] Key type id_legacy registered
[ 0.895479] ntfs: driver 2.1.31 [Flags: R/O].
[ 0.895555] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 0.895918] msgmni has been set to 7899
[ 0.896048] bounce: pool size: 64 pages
[ 0.896081] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.896085] io scheduler noop registered
[ 0.896088] io scheduler deadline registered (default)
[ 0.896473] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.926964] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.958036] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 0.958446] Linux agpgart interface v0.103
[ 0.958499] vesafb: mode is 1024x768x16, linelength=2048, pages=0
[ 0.958502] vesafb: scrolling: redraw
[ 0.958505] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.958522] vesafb: framebuffer at 0xf8000000, mapped to 0xffffc90000080000, using 3072k, total 4096k
[ 0.961459] Console: switching to colour frame buffer device 128x48
[ 0.962842] fb0: VESA VGA frame buffer device
[ 0.962880] ioatdma: Intel(R) QuickData Technology Driver 4.00
[ 0.962928] xenfs: not registering filesystem on non-xen platform
[ 0.964520] brd: module loaded
[ 0.965335] loop: module loaded
[ 0.965354] Loading iSCSI transport class v2.0-870.
[ 0.965430] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 0.965489] SCSI Media Changer driver v0.25
[ 0.965516] Atheros(R) L2 Ethernet Driver - version 2.2.3
[ 0.965530] Copyright (c) 2007 Atheros Corporation.
[ 0.965558] jme: JMicron JMC2XX ethernet driver version 1.0.8
[ 0.965594] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.965612] ehci-pci: EHCI PCI platform driver
[ 0.965672] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.972732] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.972752] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.972878] mousedev: PS/2 mouse device common for all mice
[ 0.973138] rtc_cmos 00:00: RTC can wake from S4
[ 0.995614] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.996323] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[ 0.999023] rtc_cmos 00:00: alarms up to one month, 114 bytes nvram
[ 0.999698] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.000462] usbcore: registered new interface driver usbhid
[ 1.001016] usbhid: USB HID core driver
[ 1.001714] TCP: cubic registered
[ 1.006560] NET: Registered protocol family 17
[ 1.007144] Key type dns_resolver registered
[ 1.008706] rtc_cmos 00:00: setting system clock to 2015-04-15 12:33:40 UTC (1429101220)
[ 1.010180] Freeing unused kernel memory: 876K (ffffffff81872000 - ffffffff8194d000)
[ 1.010839] Write protecting the kernel read-only data: 8192k
[ 1.016666] Freeing unused kernel memory: 1488K (ffff88000148c000 - ffff880001600000)
[ 1.018699] Freeing unused kernel memory: 388K (ffff88000179f000 - ffff880001800000)
[ 1.426598] psmouse serio1: trackpoint: failed to get extended button data
[ 1.507218] libata version 3.00 loaded.
[ 1.800236] ata_piix 0000:00:07.1: version 2.13
[ 1.800370] ata_piix 0000:00:07.1: Hyper-V Virtual Machine detected, ATA device ignore set
[ 1.803655] scsi host0: ata_piix
[ 1.804253] scsi host1: ata_piix
[ 1.804307] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 1.804310] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 1.926707] tsc: Refined TSC clocksource calibration: 2399.480 MHz
[ 1.962815] ata2.00: ATAPI: Virtual CD, , max MWDMA2
[ 1.964113] ata2.00: configured for MWDMA2
[ 1.965689] ata1.00: host indicates ignore ATA devices, ignored
[ 1.966467] scsi 1:0:0:0: CD-ROM Msft Virtual CD/ROM 1.0 PQ: 0 ANSI: 5
[ 1.968914] sr 1:0:0:0: [sr0] scsi3-mmc drive: 0x/0x tray
[ 1.968916] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.969046] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.999913] sr 1:0:0:0: Attached scsi generic sg0 type 5
[ 2.107672] scsi: <fdomain> Detection failed (no card)
[ 2.111254] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 2.256465] Fusion MPT base driver 3.04.20
[ 2.256467] Copyright (c) 1999-2008 LSI Corporation
[ 2.264541] Fusion MPT SPI Host driver 3.04.20
[ 2.269545] Fusion MPT FC Host driver 3.04.20
[ 2.277632] Fusion MPT SAS Host driver 3.04.20
[ 2.282350] 3ware Storage Controller device driver for Linux v1.26.02.003.
[ 2.286644] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[ 2.296670] HP CISS Driver (v 3.6.26)
[ 2.311783] Adaptec aacraid driver 1.2-0[30300]-ms
[ 2.319566] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 2.319886] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 2.326502] megasas: 06.805.06.00-rc1 Thu. Sep. 4 17:00:00 PDT 2014
[ 2.332450] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.07.00.16-k.
[ 2.346972] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 2.351599] mpt2sas version 18.100.00.00 loaded
[ 2.391604] usbcore: registered new interface driver usb-storage
[ 2.395116] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.398898] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.605474] device-mapper: uevent: version 1.0.3
[ 2.605562] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: dm-devel@redhat.com
[ 2.816902] raid6: sse2x1 3985 MB/s
[ 2.986942] raid6: sse2x2 5380 MB/s
[ 3.156989] raid6: sse2x4 6710 MB/s
[ 3.156991] raid6: using algorithm sse2x4 (6710 MB/s)
[ 3.156992] raid6: using ssse3x2 recovery algorithm
[ 3.159449] xor: measuring software checksum speed
[ 3.257039] prefetch64-sse: 8994.800 MB/sec
[ 3.357056] generic_sse: 8001.200 MB/sec
[ 3.357057] xor: using function: prefetch64-sse (8994.800 MB/sec)
[ 3.359305] md: raid10 personality registered for level 10
[ 3.359695] md: raid1 personality registered for level 1
[ 3.359834] async_tx: api initialized (async)
[ 3.361520] md: raid6 personality registered for level 6
[ 3.361522] md: raid5 personality registered for level 5
[ 3.361522] md: raid4 personality registered for level 4
[ 3.361757] device-mapper: raid: Loading target version 1.6.0
[ 3.367612] md: raid0 personality registered for level 0
[ 3.390283] md: linear personality registered for level -1
[ 3.393338] md: multipath personality registered for level -4
[ 3.448342] Btrfs loaded
[ 3.465740] JFS: nTxBlock = 8192, nTxLock = 65536
[ 3.498923] fuse init (API version 7.23)
[ 3.511171] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 3.511173] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 3.516958] pps_core: LinuxPPS API ver. 1 registered
[ 3.516960] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 3.517395] PTP clock support registered
[ 3.538344] iscsi: registered transport (tcp)
[ 5.759334] psmouse serio1: trackpoint: IBM TrackPoint firmware: 0x01, buttons: 0/0
[ 5.761038] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input2
[ 7.932586] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 7.934626] ISO 9660 Extensions: RRIP_1991A
[ 16.024717] random: nonblocking pool is initialized
[ 16.637038] systemd-udevd[11437]: starting version 216
[ 16.846645] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 16.846697] ACPI: Power Button [PWRF]
[ 16.871363] Floppy drive(s): fd0 is 1.44M
[ 16.899831] FDC 0 is an 82078.
[ 16.925982] hv_vmbus: Hyper-V Host Build:7601-6.1-17-0.17939; Vmbus version:1.1
[ 21.933286] hv_vmbus: registering driver hid_hyperv
[ 21.939298] input: Microsoft Vmbus HID-compliant Mouse as /devices/0006:045E:0621.0001/input/input4
[ 21.940581] hid-generic 0006:045E:0621.0001: input: <UNKNOWN> HID v0.01 Mouse [Microsoft Vmbus HID-compliant Mouse] on
[ 21.943634] hv_vmbus: registering driver hv_netvsc
[ 21.947501] hv_netvsc: hv_netvsc channel opened successfully
[ 21.953514] hv_vmbus: registering driver hv_storvsc
[ 21.954576] hv_utils: Registering HyperV Utility Driver
[ 21.954578] hv_vmbus: registering driver hv_util
[ 22.731553] hv_netvsc vmbus_0_9: Send section size: 6144, Section count:2560
[ 22.732217] hv_netvsc vmbus_0_9: Device MAC 00:15:5d:02:fe:13 link state up
[ 22.740298] scsi host2: storvsc_host_t
[ 22.740583] scsi 2:0:0:0: Direct-Access Msft Virtual Disk 1.0 PQ: 0 ANSI: 4
[ 22.740974] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 22.741367] sd 2:0:0:0: [sda] 83886080 512-byte logical blocks: (42.9 GB/40.0 GiB)
[ 22.741415] sd 2:0:0:0: [sda] Write Protect is off
[ 22.741419] sd 2:0:0:0: [sda] Mode Sense: 0f 00 10 00
[ 22.741526] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 22.743077] sda: sda1 sda2 sda3 sda4
[ 22.743679] sd 2:0:0:0: [sda] Attached SCSI disk
[ 24.153261] blk_update_request: I/O error, dev fd0, sector 0
[ 24.153265] floppy: error -5 while reading block 0
[ 24.996238] warning: process `hwsetup' used the deprecated sysctl system call with 1.23.
[ 33.996140] NET: Registered protocol family 10
[ 34.367474] cfg80211: Calling CRDA to update world regulatory domain
[ 34.408022] cfg80211: World regulatory domain updated:
[ 34.408025] cfg80211: DFS Master region: unset
[ 34.408026] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 34.408030] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 34.408032] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 34.408034] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 34.408037] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 34.408040] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 34.408042] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 34.408045] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 34.408047] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 344.532917] Key type cifs.idmap registered
[ 344.567959] Status code returned 0xc000006d NT_STATUS_LOGON_FAILURE
[ 344.567966] CIFS VFS: Send error in SessSetup = -13
[ 344.568028] CIFS VFS: cifs_mount failed w/return code = -13
[ 364.782879] Status code returned 0xc000006d NT_STATUS_LOGON_FAILURE
[ 364.782887] CIFS VFS: Send error in SessSetup = -13
[ 364.782950] CIFS VFS: cifs_mount failed w/return code = -13
[ 400.398674] Status code returned 0xc000006d NT_STATUS_LOGON_FAILURE
[ 400.398682] CIFS VFS: Send error in SessSetup = -13
[ 400.398745] CIFS VFS: cifs_mount failed w/return code = -13
[ 526.628390] EXT4-fs (sda4): recovery complete
[ 526.628785] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
|
|
|
| Back to top |
|
|
TigerJr
Guru
Joined: 19 Jun 2007
Posts: 540
|
| Posted: Tue Apr 21, 2015 10:25 am Post subject: |
|
|
dmesg нужен с твоего ядра, а не ядра с загрузочного диска. Хотя-бы последние строк 30 перед Kernel Panic
_________________
Do not use gentoo, it die |
|
| Back to top |
|
|
rino88
n00b
Joined: 02 Apr 2015
Posts: 5
|
| Posted: Tue Apr 28, 2015 9:25 am Post subject: |
|
|
| А как его получить, если я не могу загрузиться? |
|
| Back to top |
|
|
TigerJr
Guru
Joined: 19 Jun 2007
Posts: 540
|
| Posted: Thu Apr 30, 2015 9:01 pm Post subject: |
|
|
| rino88 wrote: | | А как его получить, если я не могу загрузиться? |
Сфотографируй на сотовый или планшет, фотку выложи как сделал Slavok в этой теме
https://forums.gentoo.org/viewtopic-t-1013934-highlight-.html
| rino88 wrote: |
Установил gentoo на HYPER-V сервер. После настройки по хэндбуку и перезагрузки кернел яро паникует.
|
я бы тоже паниковал если меня туда бы запихнули.
P\S
kerneldump'ом грузить не буду... хотя можно было бы
| Quote: |
Тем временем в kernel .config:
CONFIG_EARLY_PRINTK:
│
│ Write kernel log output directly into the VGA buffer or to a serial
│ port.
если есть время по извращаться
|
P\S2
А что с кернел конфигом? Не хотелось бы играть в игру - угадай модуль в кернел конфиге их там ~3500 вместе с функциями
По всей видимости у тебя не верно настроен конфиг ядра, чтобы что-то поправить нужно понять как у тебя ядро, паникующее, сконфигурировано сравнив с тем ядром (dmesg который ты выложил).
_________________
Do not use gentoo, it die |
|
| Back to top |
|
|
rino88
n00b
Joined: 02 Apr 2015
Posts: 5
|
|
| Back to top |
|
|
TigerJr
Guru
Joined: 19 Jun 2007
Posts: 540
|
| Posted: Sun May 17, 2015 10:07 am Post subject: |
|
|
Корневой раздел у тебя на sda4? Попробуй загрузчик привести к такому виду:
| Quote: | | kernel /boot/vmlinux-3.18.9-gentoo root=/dev/sda4 |
И вижу кернел ругается на несоответствие геометрии диска для файловой системы ext4.
| Quote: | | EXT4-fs (sda4): bad geometry: block count 9370880 exceeds size of device 9370720 |
возможно диск требуется переформатировать
_________________
Do not use gentoo, it die |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Russian
