| View previous topic :: View next topic |
| Author |
Message |
pranavpalliyil
n00b
Joined: 13 Oct 2021
Posts: 9
|
 Posted: Wed Oct 13, 2021 1:46 pm Post subject: Broadcom BCM4352 not working. [Solved] |
 |
|
I am new to Gentoo, and this is the first time I have installed it on my Dell Precision M4800. I have Broadcom BCM4352 wifi but I cannot get Wi-Fi to work. I have tried configuring the kernel a couple of times and have even.then I havent been very lucky.
I see my card when i use lspci -k:
| Code: | 03:00.0 Network controller: Broadcom Inc. and subsidiaries BCM4352 802.11ac Wireless Network Adapter (rev 03)
Subsystem: Dell BCM4352 802.11ac Wireless Network Adapter
Kernel driver in use: bcma-pci-bridge
Kernel modules: bcma, wl
|
But when I try ifconfig this is the reply:
| Code: | eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.10 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::236e:d411:fa26:e504 prefixlen 64 scopeid 0x20<link>
ether 20:47:47:ab:fc:72 txqueuelen 1000 (Ethernet)
RX packets 12403 bytes 12461812 (11.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 6054 bytes 964520 (941.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 20 memory 0xf7a00000-f7a20000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
This is the output of dmesg:
https://pastebin.com/uskQJrNp
Any help would be greatly appreciated. I am new to Gentoo and I am very excited to learn through this OS. Thank you
Edit: I just had to disable B4xxx drivers that were conflicting.
[Moderator edit: added [code] tags to preserve output layout. -Hu]
Last edited by pranavpalliyil on Wed Oct 13, 2021 5:24 pm; edited 1 time in total |
|
| Back to top |
|
 |
alamahant
Advocate
Joined: 23 Mar 2019
Posts: 3960
|
| Posted: Wed Oct 13, 2021 2:53 pm Post subject: |
|
|
Plz try
| Code: |
emerge -av broadcom-sta linux-firmware
rfkill list ### to check if wifi is blocked
|
If it still doesnt work then try if it works when you boot into a livecd.
If it does then it is a kernel and/or initrd thing.
In that case emerge
gentoo-kernel-bin
and see if it works.
If yes then you will have to work on your kernel .config
_________________
 |
|
| Back to top |
|
|
Hu
Administrator
Joined: 06 Mar 2007
Posts: 23273
|
| Posted: Wed Oct 13, 2021 3:17 pm Post subject: |
|
|
| Are you expecting that ifconfig should show the wireless device? Remember that a bare ifconfig does not show interfaces that are down. It's possible that your wireless interface is working, but you never configured a client for it to acquire an address and bring the interface up. If you still need help, please show the output of ip a and tell us what wireless client you are using. wpa_supplicant is popular. |
|
| Back to top |
|
|
|
Networking & Security
