damm n00b
Joined: 12 Nov 2003 Posts: 12
|
Posted: Mon Dec 15, 2003 5:02 pm Post subject: Can't use firewire harddisk under YellowDog Linux! |
|
|
Hi. I have an iBook(G3 800). I bought a 1394 hard drive(the brand is buslink) and a maxtor 80G harddisk. I installed the harddisk into the hard drive and it worked fine under OSX10.2.8. But under YellowDog Linux 3, I couldn't use it. The 2.4.22 kernel even can't recognize that a device has logged in. The 2.6 test 11 kernel recognized it but can't use it. The following is the main output from 2.6 kernel when I probemod sbp2.(I checked all the necessary kernel options. Only sbp2 was compiled into a module, and the others were compiled into the kernel)
ohci1394: $Rev: 1045 $ Ben Collins <bcollins@debian.org>
ohci1394_0: Unexpected PCI resource length of 1000!
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
[c01bf9d0] ohci1394_pci_probe+0x440/0x504
bus ieee1394: add driver sbp2
scsi1 : SCSI emulation for IEEE-1394 SBP-2 Devices
ieee1394: sbp2: Logged into SBP-2 device
ieee1394: sbp2: Node 0-00:1023: Max speed [S400] - Max payload [2048]
Vendor: Maxtor 6 Model: Y080L0 Rev:
Type: Direct-Access ANSI SCSI revision: 06
bus scsi: add device 1:0:0:0
SCSI device sda: 160086528 512-byte hdwr sectors (81964 MB)
sda: asking for cache data failed
sda: assuming drive cache: write through
sda:<3>ieee1394: sbp2: aborting sbp2 command
Read (10) 00 00 00 00 00 00 00 08 00
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
scsi: Device offlined - not ready after error recovery: host 1 channel 0 id 0 lun 0
SCSI error : <1 0 0 0> return code = 0x6050000
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
scsi1 (0:0): rejecting I/O to offline device
Buffer I/O error on device sda, logical block 0
unable to read partition table
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
bound device '1:0:0:0' to driver 'sd'
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
bound device '0006ca0e0400769f-0' to driver 'sbp2' |
|