| View previous topic :: View next topic |
| Author |
Message |
gtbX
Tux's lil' helper
Joined: 11 Oct 2003
Posts: 126
|
 Posted: Sat Jan 21, 2023 6:13 am Post subject: Booting headless Ultra 60 via GRUB |
 |
|
I've been experimenting with the 64bit UL on Sparc, and have hit an issue booting via GRUB.
I've been following the handbook installing the new system, and have installed grub according to the documentation. However, when trying to reboot, it just hangs:
| Code: | Resetting ...
Sun Ultra 60 UPA/PCI (2 X UltraSPARC-II 450MHz), No Keyboard
OpenBoot 3.17, 1024 MB memory installed, Serial #1xxxxxxx.
Ethernet address 8:0:20:x:x:x, Host ID: 80xxxxxx.
Rebooting with command: boot
Boot device: disk File and args:
GRUB Loading kernel..
|
Sending a break signal does nothing; I have to hard power-cycle to recover. This is a headless system with serial console - maybe grub is trying to show the graphical boot menu? Fortunately I can still boot using silo on the second disk, but that's not a permanent solution. This is the output I get when trying to run grub-install:
| Code: | # grub-install --target=sparc64-ieee1275 --recheck --force --skip-fs-probe /dev/sda1
Installing for sparc64-ieee1275 platform.
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/sda,sun1,sun2).
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/sda,sun1,sun4).
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/sda,sun1,sun5).
grub-install: warning: Attempting to install GRUB to a disk with multiple partition labels. This is not supported yet..
grub-install: warning: Embedding is not possible. GRUB can only be installed in this setup by using blocklists. However, blocklists are UNRELIABLE and their use is discouraged..
Installation finished. No error reported. |
As a secondary issue (when I do get it booted) only one CPU is detected by Linux, but I should probably make a separate thread for that. |
|
| Back to top |
|
 |
Murmass
n00b
Joined: 03 Oct 2023
Posts: 1
|
| Posted: Tue Oct 03, 2023 2:19 am Post subject: |
|
|
Since this is a headless system, it might be that GRUB is trying to display its interface over a graphical console and isn't set up to use the serial console. You should configure GRUB to use the serial console. You can do this by modifying the /etc/default/grub.
_________________
https://rentola.fi/
Last edited by Murmass on Wed Oct 11, 2023 6:17 pm; edited 1 time in total |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54577
Location: 56N 3W
|
| Posted: Tue Oct 03, 2023 9:34 am Post subject: |
|
|
gtbX,
I boot a server with grub output redirected to a serial port.
It needs | Code: | # Set to 'text' to force the Linux kernel to boot in normal text
# mode, 'keep' to preserve the graphics mode set using
# 'GRUB_GFXMODE', 'WIDTHxHEIGHT'['xDEPTH'] to set a particular
# graphics mode, or a sequence of these separated by commas or
# semicolons to try several modes in sequence.
#GRUB_GFXPAYLOAD_LINUX=
GRUB_GFXPAYLOAD_LINUX=text |
in /etc/default/grub and grub.cfg rewritten.
That gets me the grub menu on the serial port.
I used to run a U10. When that failed it was replaced by one of the first Raspberry Pis :)
Grub was not an option then.
| Code: | | GRUB Loading kernel.. |
if that means what it says, do you have serial console support set up on the kernel command line and in the kernel?
Can you put your grub.cfg onto a pastebin please?
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
gtbX
Tux's lil' helper
Joined: 11 Oct 2003
Posts: 126
|
| Posted: Sat Oct 14, 2023 4:05 am Post subject: |
|
|
I tried setting "GRUB_GFXPAYLOAD_LINUX=text", and re-ran grub-mkconfig, but there was no change in the result. It still hangs at Loading kernel..
I also tried uncommenting "GRUB_TERMINAL=console", but that didn't make a difference either (the comment even suggests it's only for x86(_64))
/etc/defaults/grub
I would think that if it was loading the graphical UI, it would eventually time-out and continue booting the default kernel. I've waited a few minutes and nothing seems to happen. The fact that sending a break (e.g Stop-A from a serial console) doesn't get the "ok" prompt back leads me to believe that it's crashed for some reason.
Is there a particular reason that SILO isn't supported for 64-bit userlands? Perhaps it needs a 32bit compiler available? |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54577
Location: 56N 3W
|
| Posted: Sat Oct 14, 2023 11:55 am Post subject: |
|
|
gtbX,
You need to set up the serial port for grub.
| Code: | GRUB_TERMINAL="console serial"
GRUB_SERIAL_COMMAND="serial efi0 --speed=115200 --word=8 --parity=no --stop=1" |
It won't be efi0 on a U60.
You need to set up the kernel to output the console on the serial port too.
| Code: | # Append parameters to the linux kernel command line for non-recovery entries
#GRUB_CMDLINE_LINUX_DEFAULT=""
GRUB_CMDLINE_LINUX_DEFAULT="earlyprintk console=tty0 console=ttyS0,115200n8" |
console=tty0 is the normal console and console=ttyS0,115200n is the serial console on /dev/ttyS0.
That's 115200 baud, no parity and 8 data bits.
The serial ports settings need to be the same everywhere, or you get nothing or a big mess.
My /etc/default/grub for an EFI system is there.
Lastly /etc/inittab needs to be edited to set up a serial console.
| Code: | # SERIAL CONSOLES
s0:12345:respawn:/sbin/agetty -L 115200 ttyAMA0 vt100
#s0:12345:respawn:/sbin/agetty -L 9600 ttyS0 vt100
#s1:12345:respawn:/sbin/agetty -L 9600 ttyS1 vt100 |
Without that, you get all the kernel messages on the serial console but no login: prompt.
Note that my serial port starts out as ttyS0 but here its ttyAMA0.
/boot/grub/grub.cfg contains
| Code: | echo 'Loading 6.3.1-gentoo ...'
linux /6.3.1-gentoo root=UUID=00cae814-b56c-4b3d-89b9-a5ac50a08ec9 ro net.ifnames=0 earlyprintk console=tty0 console=ttyS0,115200n8 console=ttyAMA0,115200n8 rcutree.use_softirq=0
echo 'Loading Initramfs ...'
initrd /initramfs
|
The serial port device names change, so I give both on the kernel command line.
The initrd is because I have root in LVM on top of kernel RAID.
-- edit --
I've been very naughty here. Editing /boot/grub/grub.cfg directly.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Gentoo on Sparc
