| View previous topic :: View next topic |
| Author |
Message |
zimy
n00b
Joined: 17 Jun 2024
Posts: 6
|
 Posted: Mon Jun 17, 2024 12:39 pm Post subject: Gentoo Minimal Installation CD Hang |
 |
|
Hi, I own a Dell XPS 13 9340 laptop. When booting the installation CD, i encountered this:
| Code: | EFI stub: Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path
EFI stub: Measured initrd data into PCR 9 |
The installation freezes here until I force shutdown the laptop. How do I know what is the issue here? I already disabled secure boot. |
|
| Back to top |
|
 |
RumpletonBongworth
Tux's lil' helper
Joined: 17 Jun 2024
Posts: 77
|
| Posted: Mon Jun 17, 2024 9:23 pm Post subject: |
|
|
| There is no way to know from those messages alone but I've seen it be suggested elsewhere that early microcode loading can backfire on some systems. You could try specifying dis_ucode_ldr as an additional kernel cmdline parameter to see whether this consideration applies to you (it disables the microcode loader). |
|
| Back to top |
|
|
zimy
n00b
Joined: 17 Jun 2024
Posts: 6
|
| Posted: Wed Jun 19, 2024 4:13 am Post subject: |
|
|
| RumpletonBongworth wrote: | | There is no way to know from those messages alone but I've seen it be suggested elsewhere that early microcode loading can backfire on some systems. You could try specifying dis_ucode_ldr as an additional kernel cmdline parameter to see whether this consideration applies to you (it disables the microcode loader). |
Thank you for your response. Where should I put this parameter? |
|
| Back to top |
|
|
RumpletonBongworth
Tux's lil' helper
Joined: 17 Jun 2024
Posts: 77
|
| Posted: Wed Jun 19, 2024 10:04 am Post subject: |
|
|
| zimy wrote: | | Where should I put this parameter? |
At the grub menu, press the 'e' key to enable its editing mode. The parameter would need to be appended to the line beginning with "linux /boot/gentoo". Next, press Ctrl+x to boot. After entering the edit mode, the keyboard shortcuts are described at the bottom of the screen so it should be fairly straightforward. |
|
| Back to top |
|
|
zimy
n00b
Joined: 17 Jun 2024
Posts: 6
|
| Posted: Wed Jun 19, 2024 5:53 pm Post subject: |
|
|
| RumpletonBongworth wrote: | | zimy wrote: | | Where should I put this parameter? |
At the grub menu, press the 'e' key to enable its editing mode. The parameter would need to be appended to the line beginning with "linux /boot/gentoo". Next, press Ctrl+x to boot. After entering the edit mode, the keyboard shortcuts are described at the bottom of the screen so it should be fairly straightforward. |
So this should be the edited grub command?
| Code: |
linux /boot/gentoo dokeymap looptype=squashfs loop=/image.squashfs cdroot dis_ucode_ldr
initrd /boot/gentoo.igz
|
Still freezes on the screen mentioned. |
|
| Back to top |
|
|
RumpletonBongworth
Tux's lil' helper
Joined: 17 Jun 2024
Posts: 77
|
| Posted: Wed Jun 19, 2024 6:00 pm Post subject: |
|
|
Yes, that was the right way to try it.
It could also be that the framebuffer console isn't successfully initialised but, if so, I do not know what would be causing that. I'm afraid that I personally have no other suggestions concerning the Gentoo installation CD. However, you might be interested to know that you can install Gentoo from virtually any live environment. It doesn't have to be a Gentoo-branded one, necessarily. The only hard requirement is that the environment you're in contains the utilities necessary for partitioning, filesystem creation etc, and that you are able to access the Internet using it. Perhaps try the Arch Linux boot CD (that, too, is fairly minimalistic). |
|
| Back to top |
|
|
|
Installing Gentoo
