| View previous topic :: View next topic |
| Author |
Message |
lars_the_bear
Guru
Joined: 05 Jun 2024
Posts: 522
|
 Posted: Thu Jun 27, 2024 12:58 pm Post subject: [Solved] Can't install KiCAD because of some Python problem |
 |
|
Hi folks
I'm trying to set up KiCAD on a Gentoo system I just installed. By `emerge sci-electronics/kicad` fails with an error message:
| Code: |
The following REQUIRED_USE flag constraints are unsatisfied: exactly-on-of ( python_single_target_python3_10 python_single_target_python3_10 )
|
There's some discussion of similar topics elsewhere on this forum, but I didn't understand it. FWIW `emerge --info` shows
PYTHON_SINGLE_TARGET="python3_12" and PYTHON_TARGETS="python3_12"
I'm afraid I don't know what any of this means. Can anybody tell me what I need to do to proceed?
BR, Lars.
Last edited by lars_the_bear on Fri Jun 28, 2024 5:36 pm; edited 1 time in total |
|
| Back to top |
|
 |
grknight
Retired Dev
Joined: 20 Feb 2015
Posts: 1921
|
| Posted: Thu Jun 27, 2024 1:08 pm Post subject: |
|
|
I would suggest to allow the testing ebuild of sci-electronics/kicad by placing it in /etc/portage/package.accept_keywords (which indirectly requires dev-python/wxpython there too)
This supports python 3.12 and will be less of a headache than trying to use a stable which is python 3.11 or less.
On the other hand, if version 8 is undesirable for a different technical reason, then the only choice is to enable the python3_11 single target and disable the python3_12 single target in package.use. This will then cascade down the python chain, often quite deep. |
|
| Back to top |
|
|
lars_the_bear
Guru
Joined: 05 Jun 2024
Posts: 522
|
| Posted: Thu Jun 27, 2024 5:09 pm Post subject: |
|
|
OK, thanks. I have started installing it. Looks like it could take a while.
KiCAD has a dependency on WxWidgets, which I kind-of understand. But do you know, or does anybody know, why WxWidgets had a dependency on GStreamer? KiCAD is not (so far as I know) known for its media capabilities. I can't see why it would need GStreamer, even indirectly.
GStreamer is one of the things I usually avoid; not for any good reason, but because I assume that anything so closely associated with Gnome must be bad  It's a pretty substantial thing to have to compile from source, if you don't need it.
BR, Lars. |
|
| Back to top |
|
|
eschwartz
Developer
Joined: 29 Oct 2023
Posts: 227
|
| Posted: Fri Jun 28, 2024 1:48 am Post subject: |
|
|
From the ebuild:
| Code: |
# wxPython doesn't seem to be able to optionally disable features. webkit is
# optionally patched out because it's so huge, but other elements are not,
# which makes us have to require all features from wxGTK
DEPEND="
>=x11-libs/wxGTK-3.0.4-r301:${WX_GTK_VER}=[gstreamer,libnotify,opengl,sdl,tiff,webkit?,X]
....
python_prepare_all() {
if ! use webkit; then
eapply "${FILESDIR}/${PN}-4.2.0-no-webkit.patch"
fi
|
Perhaps you could convince upstream to add a build option for disabling gstreamer. |
|
| Back to top |
|
|
lars_the_bear
Guru
Joined: 05 Jun 2024
Posts: 522
|
| Posted: Fri Jun 28, 2024 6:53 am Post subject: |
|
|
| eschwartz wrote: |
Perhaps you could convince upstream to add a build option for disabling gstreamer. |
To be honest, alongside the colossal size of KiCAD, the 50Mb or so of GStreamer is a drop in the ocean.
KiCAD 8 does work on my system, after twelve hours of compilation; but it's not as fast as 7.0.9, which is what I've used up until now. But isn't that always the case?
BR, Lars. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Installing Gentoo
