| View previous topic :: View next topic |
| Author |
Message |
thegrind
n00b
Joined: 22 Sep 2024
Posts: 12
|
 Posted: Wed Nov 06, 2024 5:12 am Post subject: Giving wlan0 priority over eth0 |
 |
|
| I have installed Gentoo on my RPi5. The Pi has a connection for the ethernet cable and wifi. I have them both connected and they both have different local ips so for example eth0 has 192.168.1.10 and wlan0 has 192.168.1.11. My wifi connection is faster so I would like to use this is as the default interface but every time I boot it defaults to eth0. Does anyone know how I can set this up. I did it before with NetworkManager by using nmcli and setting a priority so I'd like to see if I could do something similar with iwd instead of having to switch to NM. |
|
| Back to top |
|
 |
pingtoo
Veteran
Joined: 10 Sep 2021
Posts: 1227
Location: Richmond Hill, Canada
|
| Posted: Wed Nov 06, 2024 7:19 am Post subject: |
|
|
Have you tried with nmcli?
I don't use wifi for my rpi5, but nmcli does show | Code: | rpi5 ~ # nmcli
end0: connected to Wired connection 1
"end0"
ethernet (macb), 2C:xx:xx:xx:xx:xx, hw, mtu 1500
ip4 default
inet4 192.168.xx.xx/24
route4 192.168.xx.0/24 metric 100
route4 default via 192.168.xx.xx metric 100
docker0: connected (externally) to docker0
"docker0"
bridge, 02:42:C0:5D:C6:4F, sw, mtu 1500
inet4 172.17.0.1/16
route4 172.17.0.0/16 metric 0
inet6 fe80::42:c0ff:fe5d:c64f/64
route6 fe80::/64 metric 256
lo: connected (externally) to lo
"lo"
loopback (unknown), 00:00:00:00:00:00, sw, mtu 65536
inet4 127.0.0.1/8
inet6 ::1/128
wlan0: unavailable
"Broadcom Wi-Fi"
wifi (brcmfmac), xx:xx:xx:xx:xx:xx, sw disabled, hw, mtu 1500
DNS configuration:
servers: 192.168.xx.xx
domains: home
interface: end0
Use "nmcli device show" to get complete information about known devices and
"nmcli connection show" to get an overview on active connection profiles.
Consult nmcli(1) and nmcli-examples(7) manual pages for complete usage details.
rpi5 ~ # |
And networkcli show | Code: | rpi5 ~ # networkctl
IDX LINK TYPE OPERATIONAL SETUP
1 lo loopback - unmanaged
2 end0 ether - unmanaged
3 wlan0 wlan - unmanaged
4 docker0 bridge - unmanaged
4 links listed. |
|
|
| Back to top |
|
|
szatox
Advocate
Joined: 27 Aug 2013
Posts: 3410
|
| Posted: Wed Nov 06, 2024 9:01 am Post subject: |
|
|
1) Why not just unplug the wire if you don't want to use it anyway?
2) What do you use to manage wired connection? I though iwd handles wireless part and is a replacement for wpa_supplicant rather than networkmanager, am I wrong about it?
_________________
Make Computing Fun Again |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Gentoo on ARM
