| View previous topic :: View next topic |
| Author |
Message |
hotcobra
n00b
Joined: 16 Jan 2025
Posts: 2
|
 Posted: Thu Jan 16, 2025 10:54 pm Post subject: Wifi on Raspberry PI500 |
 |
|
I have been following. DarthJoker's https://forums.gentoo.org/viewtopic-t-1166940-highlight-raspberry+wifi.html trying to get wifi up and running on my PI500 (a PI 5 in a keyboard). However, I can't seem to get it running.
The wlan0 interface claims up. I have installed raspberry firmware
| Code: |
ifconfig -a
end0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.16.1.129 netmask 255.255.255.0 broadcast 172.16.1.255
inet6 fd11:e38e:9f79:7633:2ecf:67ff:fec7:f068 prefixlen 64 scopeid 0x0<global>
inet6 fe80::2ecf:67ff:fec7:f068 prefixlen 64 scopeid 0x20<link>
ether 2c:cf:67:c7:f0:68 txqueuelen 1000 (Ethernet)
RX packets 92020 bytes 6667909 (6.3 MiB)
RX errors 0 dropped 1875 overruns 0 frame 0
TX packets 43674 bytes 4938752 (4.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 106
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 256 bytes 27344 (26.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 256 bytes 27344 (26.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether da:c2:95:b4:b8:15 txqueuelen 1000 (Ethernet)
RX packets 188 bytes 14539 (14.1 KiB)
RX errors 0 dropped 34 overruns 0 frame 0
TX packets 6 bytes 744 (744.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions
|
wpa_supplicant.conf
| Code: |
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=wheel
#
# home network; allow all valid ciphers
network={
ssid="My_AP"
scan_ssid=1
key_mgmt=WPA-PSK
psk="My secret password"
}
#
|
rfkill
| Code: |
ID TYPE DEVICE SOFT HARD
0 bluetooth hci0 unblocked unblocked
1 wlan phy0 unblocked unblocked
|
dmesg
| Code: |
root 7 0.0 0.0 0 0 ? I< 02:41 0:00 [kworker/R-netns]
root 40 0.0 0.0 0 0 ? I< 02:41 0:00 [kworker/R-inet_]
root 1332 0.0 0.1 325064 15184 ? Ssl 02:41 0:01 /usr/sbin/NetworkManager --pid-file /run/NetworkManager/NetworkManager.pid
joebob 1699 0.0 0.0 3516 1792 pts/0 S+ 03:20 0:00 grep --color=auto -i net
joebob@Windows11 ~ $ ps -aux | grep wpa
root 1380 0.0 0.0 11852 8064 ? S 02:41 0:00 /usr/sbin/wpa_supplicant -u
joebob 1701 0.0 0.0 3516 1792 pts/0 S+ 03:21 0:00 grep --color=auto wpa
joebob@Windows11 ~ $ dmesg | grep -i ras
[ 0.000000] Machine model: Raspberry Pi 500 Rev 1.0
[ 0.001733] CPU features: detected: RAS Extension Support
[ 0.015993] raspberrypi-firmware soc:firmware: Attached to firmware from 2024-11-12T16:10:44, variant start_cd
[ 0.019996] raspberrypi-firmware soc:firmware: Firmware hash is 4b01994600000000000000000000000000000000
[ 0.856985] usb 3-2: Manufacturer: Raspberry Pi Ltd
[ 0.873437] input: Raspberry Pi Ltd Pi 500 Keyboard as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.0/0003:2E8A:0010.0001/input/input0
[ 1.017518] hid-generic 0003:2E8A:0010.0001: input,hidraw0: USB HID v1.11 Keyboard [Raspberry Pi Ltd Pi 500 Keyboard] on usb-xhci-hcd.1-2/input0
[ 1.033244] input: Raspberry Pi Ltd Pi 500 Keyboard Mouse as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8A:0010.0003/input/input2
[ 1.033636] input: Raspberry Pi Ltd Pi 500 Keyboard System Control as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8A:0010.0003/input/input3
[ 1.093129] input: Raspberry Pi Ltd Pi 500 Keyboard Consumer Control as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8A:0010.0003/input/input4
[ 1.093514] input: Raspberry Pi Ltd Pi 500 Keyboard as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8A:0010.0003/input/input5
[ 1.205186] hid-generic 0003:2E8A:0010.0003: input,hidraw2: USB HID v1.11 Mouse [Raspberry Pi Ltd Pi 500 Keyboard] on usb-xhci-hcd.1-2/input1
[ 2.201236] Bluetooth: hci0: BCM4345C0 'brcm/BCM4345C0.raspberrypi,5-model-b.hcd' Patch
[ 2.898978] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+-0190
[ 2024.005917] elogind-daemon[1615]: Watching system buttons on /dev/input/event0 (Raspberry Pi Ltd Pi 500 Keyboard)
[ 2024.005937] elogind-daemon[1615]: Watching system buttons on /dev/input/event3 (Raspberry Pi Ltd Pi 500 Keyboard System Control)
[ 2024.005954] elogind-daemon[1615]: Watching system buttons on /dev/input/event4 (Raspberry Pi Ltd Pi 500 Keyboard Consumer Control)
[ 2024.005969] elogind-daemon[1615]: Watching system buttons on /dev/input/event5 (Raspberry Pi Ltd Pi 500 Keyboard)
joebob@Windows11 ~ $ dmesg | more
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1]
[ 0.000000] Linux version 6.6.70-v8+ (dom@buildbot) (aarch64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1837
SMP PREEMPT Fri Jan 10 12:02:51 GMT 2025
[ 0.000000] KASLR enabled
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Raspberry Pi 500 Rev 1.0
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000001c00000, size 64 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] OF: reserved mem: 0x0000000001c00000..0x0000000005bfffff (65536 KiB) map reusable linux,cma
[ 0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff (512 KiB) nomap non-reusable atf@0
[ 0.000000] OF: reserved mem: 0x000000003fd16180..0x000000003fd161b7 (0 KiB) nomap non-reusable nvram@0
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000001ffffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0x1fef973c0-0x1fef99fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000007ffff]
[ 0.000000] node 0: [mem 0x0000000000080000-0x000000003f7fffff]
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000001ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000001ffffffff]
[ 0.000000] On node 0, zone DMA: 2048 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 30 pages/cpu s85928 r8192 d28760 u122880
[ 0.000000] pcpu-alloc: s85928 r8192 d28760 u122880 alloc=30*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Hardware dirty bit management
[ 0.000000] CPU features: detected: Spectre-v4
[ 0.000000] CPU features: detected: Spectre-BHB
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] CPU features: detected: SSBS not fully self-synchronizing
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe cgroup_disable=memory numa_policy=interleave smsc95xx.macaddr=2C:
CF:67:C7:F0:68 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p3 rootfstype=ext4 rootwait
[ 0.000000] cgroup: Disabling memory control group subsystem
[ 0.000000] mempolicy: NUMA default policy overridden to 'interleave:0'
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2062336
[ 0.000000] Policy zone: Normal
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
[ 0.000000] Memory: 8061288K/8380416K available (13440K kernel code, 2208K rwdata, 4288K rodata, 4864K init, 1086K bss, 253592K reserved, 65536K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 43603 entries in 171 pages
[ 0.000000] ftrace: allocated 171 pages with 5 groups
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[ 0.000103] Console: colour dummy device 80x25
[ 0.000106] printk: console [tty1] enabled
[ 0.000235] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
[ 0.000241] pid_max: default: 32768 minimum: 301
[ 0.000258] LSM: initializing lsm=capability,integrity
[ 0.000302] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000319] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000730] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000751] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000774] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000814] rcu: Hierarchical SRCU implementation.
[ 0.000817] rcu: Max phase no-delay instances is 1000.
[ 0.001190] EFI services will not be available.
[ 0.001241] smp: Bringing up secondary CPUs ...
[ 0.001358] Detected PIPT I-cache on CPU1
[ 0.001386] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1]
[ 0.001516] Detected PIPT I-cache on CPU2
[ 0.001538] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1]
[ 0.001662] Detected PIPT I-cache on CPU3
[ 0.001680] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1]
[ 0.001700] smp: Brought up 1 node, 4 CPUs
[ 0.001712] SMP: Total of 4 processors activated.
[ 0.001715] CPU features: detected: 32-bit EL0 Support
[ 0.001717] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.001721] CPU features: detected: Common not Private translations
[ 0.001723] CPU features: detected: CRC32 instructions
[ 0.001726] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.001728] CPU features: detected: LSE atomic instructions
[ 0.001731] CPU features: detected: Privileged Access Never
[ 0.001733] CPU features: detected: RAS Extension Support
[ 0.001736] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.001757] CPU: All CPU(s) started at EL2
[ 0.001759] alternatives: applying system-wide alternatives
[ 0.003304] devtmpfs: initialized
[ 0.005365] Enabled cp15_barrier support
[ 0.005372] Enabled setend support
[ 0.005407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.005414] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.006018] pinctrl core: initialized pinctrl subsystem
[ 0.006118] DMI not present or invalid.
[ 0.006243] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.006563] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.006604] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.006662] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.006678] audit: initializing netlink subsys (disabled)
[ 0.006715] audit: type=2000 audit(0.004:1): state=initialized audit_enabled=0 res=1
[ 0.006803] thermal_sys: Registered thermal governor 'step_wise'
[ 0.006811] cpuidle: using governor menu
[ 0.006853] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.006873] ASID allocator initialised with 32768 entries
[ 0.007070] Serial: AMBA PL011 UART driver
[ 0.007645] bcm2835-mbox 107c013880.mailbox: mailbox enabled
[ 0.007890] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 15, base_baud = 0) is a PL011 rev3
[ 0.015993] raspberrypi-firmware soc:firmware: Attached to firmware from 2024-11-12T16:10:44, variant start_cd
[ 0.019996] raspberrypi-firmware soc:firmware: Firmware hash is 4b01994600000000000000000000000000000000
[ 0.024708] /axi/pcie@120000/rp1: Fixed dependency cycle(s) with /axi/pcie@120000/rp1
[ 0.024768] /axi/interrupt-controller@7fff9000: Fixed dependency cycle(s) with /axi/interrupt-controller@7fff9000
[ 0.024935] /axi/pcie@120000/rp1: Fixed dependency cycle(s) with /axi/pcie@120000/rp1
[ 0.025534] Modules: 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[ 0.025538] Modules: 0 pages in range for non-PLT usage
[ 0.025539] Modules: 517776 pages in range for PLT usage
[ 0.028292] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1
[ 0.028543] iommu: Default domain type: Translated
[ 0.028547] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.028609] SCSI subsystem initialized
[ 0.028637] usbcore: registered new interface driver usbfs
[ 0.028644] usbcore: registered new interface driver hub
[ 0.028650] usbcore: registered new device driver usb
[ 0.028710] pps_core: LinuxPPS API ver. 1 registered
[ 0.028713] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.028718] PTP clock support registered
[ 0.028916] vgaarb: loaded
[ 0.028983] clocksource: Switched to clocksource arch_sys_counter
[ 0.029053] VFS: Disk quotas dquot_6.6.0
[ 0.029061] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.029083] FS-Cache: Loaded
[ 0.029441] CacheFiles: Loaded
[ 0.030351] NET: Registered PF_INET protocol family
[ 0.030466] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.031946] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.031995] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.032062] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.032246] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[ 0.033756] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.033861] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear)
[ 0.034005] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.034071] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.034178] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.034306] RPC: Registered named UNIX socket transport module.
[ 0.034310] RPC: Registered udp transport module.
[ 0.034311] RPC: Registered tcp transport module.
[ 0.034313] RPC: Registered tcp-with-tls transport module.
[ 0.034315] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.034321] PCI: CLS 0 bytes, default 64
[ 0.037040] kvm [1]: IPA Size Limit: 40 bits
[ 0.037062] kvm [1]: vgic interrupt IRQ9
[ 0.037075] kvm [1]: VHE mode initialized successfully
[ 0.209609] Initialise system trusted keyrings
[ 0.209660] workingset: timestamp_bits=42 max_order=21 bucket_order=0
[ 0.209676] zbud: loaded
[ 0.209803] NFS: Registering the id_resolver key type
[ 0.209810] Key type id_resolver registered
[ 0.209812] Key type id_legacy registered
[ 0.209817] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.209820] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.209924] Key type asymmetric registered
[ 0.209927] Asymmetric key parser 'x509' registered
[ 0.209936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.209968] io scheduler mq-deadline registered
[ 0.209971] io scheduler kyber registered
[ 0.209978] io scheduler bfq registered
[ 0.210129] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7c502000, parent irq: 26)
[ 0.210170] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d503000, parent irq: 27)
[ 0.210213] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508380, parent irq: 28)
[ 0.210242] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508400, parent irq: 29)
[ 0.210276] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7d510600, parent irq: 30)
[ 0.210306] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d517b00, parent irq: 31)
[ 0.211209] simple-framebuffer 3f800000.framebuffer: framebuffer at 0x3f800000, 0x3f4800 bytes
[ 0.211216] simple-framebuffer 3f800000.framebuffer: format=r5g6b5, mode=1920x1080x16, linelength=3840
[ 0.212250] Console: switching to colour frame buffer device 240x67
[ 0.213217] simple-framebuffer 3f800000.framebuffer: fb0: simplefb registered!
[ 0.241713] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 0.241997] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 33, base_baud = 6000000) is a Broadcom BCM7271 UART
[ 0.242041] serial serial0: tty port ttyS0 registered
[ 0.242258] iproc-rng200 107d208000.rng: hwrng registered
[ 0.242302] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB)
[ 0.242456] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe
[ 0.243868] brd: module loaded
[ 0.244923] loop: module loaded
[ 0.245022] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 0.245116] Loading iSCSI transport class v2.0-870.
[ 0.245749] usbcore: registered new device driver r8152-cfgselector
[ 0.245762] usbcore: registered new interface driver r8152
[ 0.245772] usbcore: registered new interface driver lan78xx
[ 0.245781] usbcore: registered new interface driver smsc95xx
[ 0.245827] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.245847] dwc_otg: FIQ enabled
[ 0.245848] dwc_otg: NAK holdoff enabled
[ 0.245848] dwc_otg: FIQ split-transaction FSM enabled
[ 0.245850] Module dwc_common_port init
[ 0.245944] usbcore: registered new interface driver uas
[ 0.245956] usbcore: registered new interface driver usb-storage
[ 0.246026] mousedev: PS/2 mouse device common for all mice
[ 0.253528] rpi-rtc soc:rpi_rtc: registered as rtc0
[ 0.254908] rpi-rtc soc:rpi_rtc: setting system clock to 2025-01-16T13:50:05 UTC (1737035405)
[ 0.255142] bcm2835-wdt bcm2835-wdt: Poweroff handler already present!
[ 0.255151] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.257154] sdhci: Secure Digital Host Controller Interface driver
[ 0.257162] sdhci: Copyright(c) Pierre Ossman
[ 0.257192] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.257339] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.257380] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 0.257396] hid: raw HID events driver (C) Jiri Kosina
[ 0.257413] usbcore: registered new interface driver usbhid
[ 0.257419] usbhid: USB HID core driver
[ 0.257641] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 counters available
[ 0.257892] NET: Registered PF_PACKET protocol family
[ 0.257919] Key type dns_resolver registered
[ 0.261443] registered taskstats version 1
[ 0.261504] Loading compiled-in X.509 certificates
[ 0.263100] Key type .fscrypt registered
[ 0.263405] Key type fscrypt-provisioning registered
[ 0.264214] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@120000 ranges:
[ 0.264511] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@120000, using [bus 00-ff]
[ 0.264807] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000
[ 0.265123] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000
[ 0.265411] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000
[ 0.265696] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[ 0.267235] brcm-pcie 1000120000.pcie: Forcing gen 2
[ 0.267693] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0000:00
[ 0.267974] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.268251] pci_bus 0000:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb])
[ 0.268532] pci_bus 0000:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff])
[ 0.268820] pci 0000:00:00.0: [14e4:2712] type 01 class 0x060400
[ 0.269125] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.270011] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.376988] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)
[ 0.377288] pci 0000:01:00.0: [1de4:0001] type 00 class 0x020000
[ 0.377573] pci 0000:01:00.0: reg 0x10: [mem 0xffffc000-0xffffffff]
[ 0.377849] pci 0000:01:00.0: reg 0x14: [mem 0xffc00000-0xffffffff]
[ 0.378120] pci 0000:01:00.0: reg 0x18: [mem 0xffff0000-0xffffffff]
[ 0.378445] pci 0000:01:00.0: supports D1
[ 0.378704] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.388991] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.389258] pci 0000:00:00.0: BAR 8: assigned [mem 0x1f00000000-0x1f005fffff]
[ 0.389519] pci 0000:01:00.0: BAR 1: assigned [mem 0x1f00000000-0x1f003fffff]
[ 0.389776] pci 0000:01:00.0: BAR 2: assigned [mem 0x1f00400000-0x1f0040ffff]
[ 0.390029] pci 0000:01:00.0: BAR 0: assigned [mem 0x1f00410000-0x1f00413fff]
[ 0.390278] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.390520] pci 0000:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]
[ 0.390764] pci_bus 0000:00: resource 4 [mem 0x1f00000000-0x1ffffffffb]
[ 0.391005] pci_bus 0000:00: resource 5 [mem 0x1c00000000-0x1effffffff pref]
[ 0.391243] pci_bus 0000:01: resource 1 [mem 0x1f00000000-0x1f005fffff]
[ 0.391478] pci 0000:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512
[ 0.391723] pci 0000:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512
[ 0.392009] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 0.392270] pcieport 0000:00:00.0: PME: Signaling with IRQ 38
[ 0.392554] pcieport 0000:00:00.0: AER: enabled with IRQ 38
[ 0.392848] rp1 0000:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200
[ 0.393097] rp1 0000:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200
[ 0.393347] rp1 0000:01:00.0: enabling device (0000 -> 0002)
[ 0.394240] rp1 0000:01:00.0: chip_id 0x20001927
[ 0.398645] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 100
[ 0.414915] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 106 (2c:cf:67:c7:f0:68)
[ 0.416164] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels
[ 0.416607] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.416865] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
[ 0.417555] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000000810
[ 0.417817] xhci-hcd xhci-hcd.0: irq 131, io mem 0x1f00200000
[ 0.418130] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.418384] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
[ 0.418639] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed
[ 0.418937] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[ 0.419194] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.419448] usb usb1: Product: xHCI Host Controller
[ 0.419702] usb usb1: Manufacturer: Linux 6.6.70-v8+ xhci-hcd
[ 0.419955] usb usb1: SerialNumber: xhci-hcd.0
[ 0.420292] hub 1-0:1.0: USB hub found
[ 0.420550] hub 1-0:1.0: 2 ports detected
[ 0.420886] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[ 0.421142] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.421394] usb usb2: Product: xHCI Host Controller
[ 0.421645] usb usb2: Manufacturer: Linux 6.6.70-v8+ xhci-hcd
[ 0.421896] usb usb2: SerialNumber: xhci-hcd.0
[ 0.422204] hub 2-0:1.0: USB hub found
[ 0.422459] hub 2-0:1.0: 1 port detected
[ 0.422900] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.423151] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
[ 0.423829] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000000810
[ 0.424092] xhci-hcd xhci-hcd.1: irq 136, io mem 0x1f00300000
[ 0.424402] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.424655] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
[ 0.424908] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed
[ 0.425204] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[ 0.425459] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.425709] usb usb3: Product: xHCI Host Controller
[ 0.425958] usb usb3: Manufacturer: Linux 6.6.70-v8+ xhci-hcd
[ 0.426206] usb usb3: SerialNumber: xhci-hcd.1
[ 0.426513] hub 3-0:1.0: USB hub found
[ 0.426766] hub 3-0:1.0: 2 ports detected
[ 0.427101] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[ 0.427352] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.427603] usb usb4: Product: xHCI Host Controller
[ 0.427853] usb usb4: Manufacturer: Linux 6.6.70-v8+ xhci-hcd
[ 0.428105] usb usb4: SerialNumber: xhci-hcd.1
[ 0.428410] hub 4-0:1.0: USB hub found
[ 0.428666] hub 4-0:1.0: 1 port detected
[ 0.429422] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.429905] platform 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 0.430166] platform 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 0.430424] platform 1000800000.codec: Adding to iommu group 0
[ 0.430687] platform 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 0.430944] platform 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 0.431204] platform 1000880000.pisp_be: Adding to iommu group 0
[ 0.431478] platform 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 0.431735] platform 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 0.431995] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success
[ 0.432535] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.433000] platform axi:gpu: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 0.433262] platform axi:gpu: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 0.433518] platform axi:gpu: Adding to iommu group 1
[ 0.433784] platform axi:gpu: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 0.434037] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success
[ 0.434583] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.435044] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success
[ 0.435974] of_cfs_init
[ 0.436249] of_cfs_init: OK
[ 0.436552] clk: Disabling unused clocks
[ 0.446552] mmc1: CQHCI version 5.10
[ 0.449126] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO
[ 0.449448] mmc0: CQHCI version 5.10
[ 0.485430] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit
[ 0.584515] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 0.584931] mmcblk0: mmc0:aaaa SN512 477 GiB
[ 0.586122] mmcblk0: p1 p2 p3
[ 0.586451] mmcblk0: mmc0:aaaa SN512 477 GiB (quirks 0x00004000)
[ 0.632983] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit
[ 0.643427] EXT4-fs (mmcblk0p3): mounted filesystem c948bafe-07d5-4936-a810-8af34cd0b7a3 ro with ordered data mode. Quota mode: none.
[ 0.643703] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
[ 0.646754] devtmpfs: mounted
[ 0.649453] Freeing unused kernel memory: 4864K
[ 0.649781] Run /sbin/init as init process
[ 0.650036] with arguments:
[ 0.650037] /sbin/init
[ 0.650038] with environment:
[ 0.650039] HOME=/
[ 0.650039] TERM=linux
[ 0.665210] mmc1: new ultra high speed DDR50 SDIO card at address 0001
[ 0.672989] usb 1-2: new low-speed USB device number 2 using xhci-hcd
[ 0.680987] usb 3-2: new full-speed USB device number 2 using xhci-hcd
[ 0.854015] usb 1-2: New USB device found, idVendor=093a, idProduct=2510, bcdDevice= 1.00
[ 0.854301] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.854559] usb 1-2: Product: USB Optical Mouse
[ 0.854806] usb 1-2: Manufacturer: PixArt
[ 0.856222] usb 3-2: New USB device found, idVendor=2e8a, idProduct=0010, bcdDevice= 0.10
[ 0.856475] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.856726] usb 3-2: Product: Pi 500 Keyboard
[ 0.856985] usb 3-2: Manufacturer: Raspberry Pi Ltd
[ 0.873437] input: Raspberry Pi Ltd Pi 500 Keyboard as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.0/0003:2E8A:0010.0001/inp
ut/input0
[ 0.883009] input: PixArt USB Optical Mouse as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-2/1-2:1.0/0003:093A:2510.0002/input/input
1
[ 1.017518] hid-generic 0003:2E8A:0010.0001: input,hidraw0: USB HID v1.11 Keyboard [Raspberry Pi Ltd Pi 500 Keyboard] on usb-xhci-hcd.1-2/input0
[ 1.018066] hid-generic 0003:093A:2510.0002: input,hidraw1: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-xhci-hcd.0-2/input0
[ 1.033244] input: Raspberry Pi Ltd Pi 500 Keyboard Mouse as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8A:0010.00
03/input/input2
[ 1.033636] input: Raspberry Pi Ltd Pi 500 Keyboard System Control as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8
A:0010.0003/input/input3
[ 1.093129] input: Raspberry Pi Ltd Pi 500 Keyboard Consumer Control as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2
E8A:0010.0003/input/input4
[ 1.093514] input: Raspberry Pi Ltd Pi 500 Keyboard as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:2E8A:0010.0003/inp
ut/input5
[ 1.205186] hid-generic 0003:2E8A:0010.0003: input,hidraw2: USB HID v1.11 Mouse [Raspberry Pi Ltd Pi 500 Keyboard] on usb-xhci-hcd.1-2/input1
[ 1.663501] input: pwr_button as /devices/platform/pwr_button/input/input6
[ 1.686400] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040
[ 1.687076] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1
[ 1.687116] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040
[ 1.687241] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2
[ 1.687295] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020
[ 1.687371] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3
[ 1.687399] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020
[ 1.687493] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4
[ 1.687578] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000
[ 1.687673] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0
[ 1.688167] rp1-firmware rp1_firmware: RP1 Firmware version e4eb725aa7bca7efe2673df3020818c0880a6e30
[ 1.712945] macb 1f00100000.ethernet end0: renamed from eth0
[ 1.718502] brcmstb-i2c 107d508200.i2c: @97500hz registered in interrupt mode
[ 1.718588] brcmstb-i2c 107d508280.i2c: @97500hz registered in interrupt mode
[ 1.722642] rp1-pio 1f00178000.pio: Created instance as pio0
[ 1.729825] mc: Linux media interface: v0.10
[ 1.784781] videodev: Linux video capture interface: v2.00
[ 1.819473] Bluetooth: Core ver 2.22
[ 1.819499] NET: Registered PF_BLUETOOTH protocol family
[ 1.819501] Bluetooth: HCI device and connection manager initialized
[ 1.819507] Bluetooth: HCI socket layer initialized
[ 1.819510] Bluetooth: L2CAP socket layer initialized
[ 1.819514] Bluetooth: SCO socket layer initialized
[ 1.830905] pispbe 1000880000.pisp_be: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 1.836893] pispbe 1000880000.pisp_be: Runtime PM usage count underflow!
[ 1.842716] [drm] Initialized v3d 1.0.0 20180419 for 1002000000.v3d on minor 0
[ 1.851153] Bluetooth: HCI UART driver ver 2.3
[ 1.851159] Bluetooth: HCI UART protocol H4 registered
[ 1.851182] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.851249] Bluetooth: HCI UART protocol Broadcom registered
[ 1.851303] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[ 1.851346] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[ 1.858558] rpivid_hevc: module is from the staging directory, the quality is unknown, you have been warned.
[ 1.859126] rpivid 1000800000.codec: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 1.861243] rpivid 1000800000.codec: Device registered as /dev/video19
[ 1.912797] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 1.914933] Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[ 1.915140] Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[ 1.915340] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 1.915538] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 2.105454] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 2.106717] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 2.106907] usbcore: registered new interface driver brcmfmac
[ 2.117045] vc4-drm axi:gpu: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 2.117812] Console: switching to colour dummy device 80x25
[ 2.119832] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 2.121075] Registered IR keymap rc-cec
[ 2.121110] rc rc0: vc4-hdmi-0 as /devices/platform/soc/107c701400.hdmi/rc/rc0
[ 2.121151] input: vc4-hdmi-0 as /devices/platform/soc/107c701400.hdmi/rc/rc0/input7
[ 2.121779] input: vc4-hdmi-0 HDMI Jack as /devices/platform/soc/107c701400.hdmi/sound/card0/input8
[ 2.124753] vc4-drm axi:gpu: bound 107c701400.hdmi (ops vc4_hdmi_ops [vc4])
[ 2.126224] Registered IR keymap rc-cec
[ 2.126266] rc rc1: vc4-hdmi-1 as /devices/platform/soc/107c706400.hdmi/rc/rc1
[ 2.126310] input: vc4-hdmi-1 as /devices/platform/soc/107c706400.hdmi/rc/rc1/input9
[ 2.126879] input: vc4-hdmi-1 HDMI Jack as /devices/platform/soc/107c706400.hdmi/sound/card1/input10
[ 2.129121] vc4-drm axi:gpu: bound 107c706400.hdmi (ops vc4_hdmi_ops [vc4])
[ 2.129326] vc4-drm axi:gpu: bound 107c500000.mop (ops vc4_txp_ops [vc4])
[ 2.129404] vc4-drm axi:gpu: bound 107c501000.moplet (ops vc4_txp_ops [vc4])
[ 2.129486] vc4-drm axi:gpu: bound 107c410000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 2.129550] vc4-drm axi:gpu: bound 107c411000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 2.179913] [drm] Initialized vc4 0.0.0 20140616 for axi:gpu on minor 1
[ 2.197496] Bluetooth: hci0: BCM: chip id 107
[ 2.197710] Bluetooth: hci0: BCM: features 0x2f
[ 2.199049] Bluetooth: hci0: BCM4345C0
[ 2.199054] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000
[ 2.201236] Bluetooth: hci0: BCM4345C0 'brcm/BCM4345C0.raspberrypi,5-model-b.hcd' Patch
[ 2.227880] EXT4-fs (mmcblk0p3): re-mounted c948bafe-07d5-4936-a810-8af34cd0b7a3 r/w. Quota mode: none.
[ 2.256575] Console: switching to colour frame buffer device 240x75
[ 2.274380] vc4-drm axi:gpu: [drm] fb0: vc4drmfb frame buffer device
[ 2.276227] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[ 2.276470] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Aug 29 2023 01:47:08 version 7.45.265 (28bca26 CY) FWID 01-b677b91b
[ 2.309093] EXT4-fs (mmcblk0p3): re-mounted c948bafe-07d5-4936-a810-8af34cd0b7a3 r/w. Quota mode: none.
[ 2.415800] Unable to find swap-space signature
[ 2.897636] Bluetooth: hci0: BCM: features 0x2f
[ 2.898978] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+-0190
[ 2.898980] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0382
[ 2.899286] Bluetooth: hci0: BCM: Using default device address (43:45:c0:00:1f:ac)
[ 3.439192] macb 1f00100000.ethernet end0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL)
[ 3.439198] macb 1f00100000.ethernet end0: configuring for phy/rgmii-id link mode
[ 3.441828] pps pps0: new PPS source ptp0
[ 3.441986] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered.
[ 3.469849] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 4.001427] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 7.518032] macb 1f00100000.ethernet end0: Link is Up - 1Gbps/Full - flow control off
[ 420.513223] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 723.521215] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 1026.529303] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 1329.537234] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 1632.513210] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 1935.521208] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 2024.003498] elogind-daemon[1615]: New seat seat0.
[ 2024.005917] elogind-daemon[1615]: Watching system buttons on /dev/input/event0 (Raspberry Pi Ltd Pi 500 Keyboard)
[ 2024.005937] elogind-daemon[1615]: Watching system buttons on /dev/input/event3 (Raspberry Pi Ltd Pi 500 Keyboard System Control)
[ 2024.005954] elogind-daemon[1615]: Watching system buttons on /dev/input/event4 (Raspberry Pi Ltd Pi 500 Keyboard Consumer Control)
[ 2024.005969] elogind-daemon[1615]: Watching system buttons on /dev/input/event5 (Raspberry Pi Ltd Pi 500 Keyboard)
[ 2024.005984] elogind-daemon[1615]: Watching system buttons on /dev/input/event6 (pwr_button)
[ 2024.005999] elogind-daemon[1615]: Watching system buttons on /dev/input/event7 (vc4-hdmi-0)
[ 2024.006501] elogind-daemon[1615]: Watching system buttons on /dev/input/event9 (vc4-hdmi-1)
[ 2024.009386] elogind-daemon[1615]: New session 1 of user root.
[ 2126.764491] NET: Registered PF_INET6 protocol family
[ 2126.764939] Segment Routing with IPv6
[ 2126.764945] In-situ OAM (IOAM) with IPv6
[ 2143.505028] elogind-daemon[1615]: New session 2 of user joebob.
[ 2238.529429] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 2541.537292] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 2844.513246] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 3147.521183] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
|
ls -l /lib/firmware/brcm/
| Code: |
-rw-r--r-- 1 root root 63806 Jan 15 2025 BCM4345C0.hcd
lrwxrwxrwx 1 root root 13 Jan 15 2025 BCM4345C0.raspberrypi,5-model-b.hcd -> BCM4345C0.hcd
-rw-r--r-- 1 root root 609309 Jan 15 2025 brcmfmac43455-sdio.bin
-rw-r--r-- 1 root root 2676 Jan 15 2025 brcmfmac43455-sdio.clm_blob
lrwxrwxrwx 1 root root 22 Jan 15 2025 brcmfmac43455-sdio.raspberrypi,5-model-b.bin -> brcmfmac43455-sdio.bin
lrwxrwxrwx 1 root root 27 Jan 15 2025 brcmfmac43455-sdio.raspberrypi,5-model-b.clm_blob -> brcmfmac43455-sdio.clm_blob
lrwxrwxrwx 1 root root 22 Jan 15 2025 brcmfmac43455-sdio.raspberrypi,5-model-b.txt -> brcmfmac43455-sdio.txt
-rw-r--r-- 1 root root 2074 Jan 15 2025 brcmfmac43455-sdio.txt
|
ps -aux
| Code: |
root 7 0.0 0.0 0 0 ? I< 02:41 0:00 [kworker/R-netns]
root 40 0.0 0.0 0 0 ? I< 02:41 0:00 [kworker/R-inet_]
root 1332 0.0 0.1 325064 15184 ? Ssl 02:41 0:01 /usr/sbin/NetworkManager --pid-file /run/NetworkManager/NetworkManager.pid
root 1380 0.0 0.0 11852 8064 ? S 02:41 0:00 /usr/sbin/wpa_supplicant -u
|
started wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -I wlan0
| Code: |
Successfully initialized wpa_supplicant
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: Trying to associate with SSID 'MY_AP'
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
wlan0: Associated with 84:70:d7:23:b9:a8
wlan0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
wlan0: CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=US
wlan0: WPA: Key negotiation completed with 84:70:d7:23:b9:a8 [PTK=CCMP GTK=CCMP]
wlan0: CTRL-EVENT-CONNECTED - Connection to 84:70:d7:23:b9:a8 completed [id=0 id_str=]
|
DROPS?
| Code: |
wlan0: CTRL-EVENT-DISCONNECTED bssid=84:70:d7:23:b9:a8 reason=3 locally_generated=1
BSSID 84:70:d7:23:b9:a8 ignore list count incremented to 2, ignoring for 10 seconds
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
|
[/quote]
What am I doing wrong? |
|
| Back to top |
|
 |
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54799
Location: 56N 3W
|
| Posted: Fri Jan 17, 2025 12:05 pm Post subject: |
|
|
hotcobra,
| Code: | | wlan0: CTRL-EVENT-DISCONNECTED bssid=84:70:d7:23:b9:a8 reason=3 locally_generated=1 |
means you told me (to drop). This is not PI 500 specific.
It usually means that you have two or more things trying to control the interface at the same time. They all fight an take it in turns to 'win' for a few seconds. That's what we see here.
The fix is the same.
Remove all the things that can control wlan0 from starting automatically.
Prove it by rebooting and verifying that wlan0 does not start.
Choose exactly one service to control wlan0.
Start that service by hand.
Verify that wlan0 works.
Add the service to the default runlevel.
Reboot to test.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
hotcobra
n00b
Joined: 16 Jan 2025
Posts: 2
|
| Posted: Sat Jan 18, 2025 5:55 pm Post subject: |
|
|
Found wpa_supplicant, dhcpcd, and NetworkManager running.
Removed them, rebooted and had no eth0, or wlan0
ReAdded NetworkManager to netmount
grep -v "^#\|^$" /etc/conf.d/netmount
| Code: |
rc_need="NetworkManager"
|
ethernet ifname changed from eth0 to end0
Added logical links for end0 and wlan0
ls -la /etc/init.d/*.lo
| Code: |
lrwxrwxrwx 1 root root 6 Jan 18 06:28 /etc/init.d/end0.lo -> net.lo
-rwxr-xr-x 1 root root 20018 Jul 21 18:19 /etc/init.d/net.lo
lrwxrwxrwx 1 root root 6 Jan 18 06:28 /etc/init.d/wlan0.lo -> net.lo
|
Tried eth0.lo as well but the IF stays end0
Used nmcli to add wlan0
| Code: |
nmcli device wifi connect My_AP password My_password ifname wlan0
|
ls /etc/NetworkManager/system-connections/
ifconfig -a
| Code: |
end0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet xxx.xx.xxx.xxx netmask 255.255.255.0 broadcast 172.16.1.255
inet6 fd11:e38e:9f79:7633:6c60:f5e6:5f2f:b23d prefixlen 64 scopeid 0x0<global>
inet6 fe80::d220:ba42:e8b9:a1dd prefixlen 64 scopeid 0x20<link>
ether 2c:cf:67:c7:f0:68 txqueuelen 1000 (Ethernet)
RX packets 37712 bytes 2639143 (2.5 MiB)
RX errors 0 dropped 735 overruns 0 frame 0
TX packets 17898 bytes 1878673 (1.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 106
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet xxx.xx.xxx.xxx netmask 255.255.255.0 broadcast 172.16.1.255
inet6 fe80::bbfb:6f0:2504:765 prefixlen 64 scopeid 0x20<link>
inet6 fd11:e38e:9f79:7633:fcfc:e71c:7017:d537 prefixlen 64 scopeid 0x0<global>
ether 2c:cf:67:c7:f0:69 txqueuelen 1000 (Ethernet)
RX packets 1436 bytes 113435 (110.7 KiB)
RX errors 0 dropped 370 overruns 0 frame 0
TX packets 156 bytes 15948 (15.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
Seems to work but where/how did eth0 change to end0?
Should I add a /etc/NetworkManager/system-connection for eth0?
Thank you for the help. |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54799
Location: 56N 3W
|
| Posted: Sat Jan 18, 2025 7:46 pm Post subject: |
|
|
hotcobra,
udev or some other autoblackmagic renamed eth0 for you.
As you no longer have an eth0, you should not try to configure it.
I don't think names matter as log as they are consistent everywhere.
is traditionally. and so on.
Just leave it in a mess for now :)
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Gentoo on ARM
