2.6.1-love3 "Watch the love!"

bAnTAi · n00b Joined: 22 Dec 2003 Posts: 15

Anyone that can answer my question on my previous post?

Wedge_ · Posted: Mon Jan 12, 2004 7:54 pm Post subject:

Try deleting /usr/portage/distfiles/2.6.1-love3.patch.bz2 and /usr/local/portage/sys-kernel/love-sources/files/digest-love-sources-2.6.1-r3, then run "ebuild love-sources-2.6.1-r3.ebuild digest" again. Hopefully after that you should be able to emerge normally.
_________________
Per Ardua Ad Astra
The Earth is the cradle of the mind, but we cannot live forever in a cradle - Konstantin E. Tsiolkovsky
Gentoo Radeon FAQ

jobeus · n00b Joined: 17 Mar 2003 Posts: 52

Why wasn't it mentioned that the omnibook module is in here?

I can finally (hopefully) get my Toshiba laptop working properly again (temperature monitoring and stuff)... The omnibook ebuild wouldn't seem to work with 2.6... Neat!

_________________
http://jobe.ca

steel300 · Veteran Joined: 10 Jul 2003 Posts: 1155

It was mentioned. Look at the line for Radeon IGP. I found a patch that has four things in one. Omnibook was one of them.
_________________
Rationality is the recognition of the fact that nothing can alter the truth and nothing can take precedence over that act of perceiving it.

PrakashP · Posted: Mon Jan 12, 2004 8:54 pm Post subject:

@Wedge_

Though asmon has a very much different system then me, I can't easily make out, what may be the cause. And as my time is limited (busy with diploma) I'll wait for mm3 based love sources and give it a try in the hope it got fixed.

Pink · Veteran Joined: 24 Jul 2003 Posts: 1062

Compiled fine but had hard lock up within a minute or so.

I applied the nforce2-apic-fix.patch wedge posted by wedge in the 2.6.1-love1 thread.

I had to reboot into an older kernel to apply the patch, so I am not sure if it was actually needed (an 'athcool stat' command reports that it is disabled, but it would be once the patch was applied!) but all is well (for the moment....)

Maybe this will help others if they are getting any lockups with nforce2

ed0n · Posted: Mon Jan 12, 2004 9:03 pm Post subject:

First of all OneofOne thanks , the sources are great.

Second of all

I have a question for you.
Can anyone tell me why when I am trying to rmmod a module its segfaulting
It is segfaulting with 2.6.1-love1/2/3 and with module-init-tools-0.9.15_pre4/
module-init-tools-3.0_pre5.

Edon

Wedge_ · Posted: Mon Jan 12, 2004 9:08 pm Post subject:

Jazz · Posted: Mon Jan 12, 2004 9:11 pm Post subject:

Ok i get the following error in dmesg.... any guesses ??

Wedge_ · Posted: Mon Jan 12, 2004 9:13 pm Post subject:

Apply this and those should go away.
_________________
Per Ardua Ad Astra
The Earth is the cradle of the mind, but we cannot live forever in a cradle - Konstantin E. Tsiolkovsky
Gentoo Radeon FAQ

Jazz · Posted: Mon Jan 12, 2004 9:18 pm Post subject:

Thanks.. i applied the patch, emm, do i need to just rebot after that, (just to see whether it worked) or should i recompiel the kernel again :?:

Bye,
Jassi

Wedge_ · Posted: Mon Jan 12, 2004 9:22 pm Post subject:

You need to recompile and reboot before it will take effect.
_________________
Per Ardua Ad Astra
The Earth is the cradle of the mind, but we cannot live forever in a cradle - Konstantin E. Tsiolkovsky
Gentoo Radeon FAQ

didl · Posted: Mon Jan 12, 2004 11:18 pm Post subject:

m3ph · n00b Joined: 09 Jan 2004 Posts: 39 Location: Estonia

does pcmcia-cs compile with this one?

Jazz · Posted: Mon Jan 12, 2004 11:28 pm Post subject:

Hey just a suggestion.. wud the following patches be good enough to get implemented in the love sources ??
Internet Speedy Patch

Bye,
Jassi

neenee · Veteran Joined: 20 Jul 2003 Posts: 1786

i use wondershaper for this. though
i do not see which patch it would be;
this is just a script which uses traffic
shaping parts of the kernel / modules.

supernova · Posted: Mon Jan 12, 2004 11:40 pm Post subject:

Hi!

Thanks for the sources, they seem to run great!

A small problem, though: When I'm booting, the first two messages I get are:

Jazz · Posted: Mon Jan 12, 2004 11:45 pm Post subject:

Hmm.. is the mrw gotto do anything with the Mount Rainer Format ?? cud it be accociated to the UDF packet writing enabled in the kernel ??

Just a passing thought..

@neene, well i dunno anything about it myself, just stumbled upon it and thought it might be an interesting thing to be added to the Love...

Cud u please elaborate on how you achieve the traffic control with the app that u use, and whether it has a gui ?

Bye,
Jassi

antisthenes · Tux's lil' helper Joined: 06 May 2003 Posts: 89

Does anyone know if loop devices work on this one? I'm forced to use a random thing I got off loop-aes.sf.net to do it, because otherwise I get ioctl errors. Someone know?

supernova · Posted: Mon Jan 12, 2004 11:57 pm Post subject:

Hello Jassi,

I had UDF support enabled, I removed it and recompiled, but the messages still appear.

As far as I can tell from my Google researches, "mrw" does indeed stand for Mt Rainier... (?)

Here is a part of my .config:

neenee · Veteran Joined: 20 Jul 2003 Posts: 1786

dedeaux · Posted: Tue Jan 13, 2004 12:37 am Post subject: compiled and working fine

I was able to successfully compile this and am currently running on it with no issues.

I moved from 2.6.0-love2 to this one. I am running it on a Korean laptop with no issues.

Thanks for the hard work.

PrakashP · Posted: Tue Jan 13, 2004 1:06 am Post subject:

@Wedge_

As 2.6.1-love1 started locking up I am giving love3 a try... And yes, your patch for kexec (or rather clean desintegration) works nicely when I don't enable kexec. For the meanwhile I disabled APIC and enabled CPU disconnect. I just want to see whether the lock are APIC related...

watersb · Posted: Tue Jan 13, 2004 2:07 am Post subject:

antisthenes · Tux's lil' helper Joined: 06 May 2003 Posts: 89

I know how to use loop-devices. I already use the loop-AES fix, but I don't need AES or any sort of encryption. All I want is my loopback devices, and without the loop-AES module replacing the normal one, I get something like: