| View previous topic :: View next topic |
| Author |
Message |
zenok
n00b
Joined: 12 Jan 2004
Posts: 45
|
 Posted: Wed Jan 14, 2004 9:58 pm Post subject: 2.6: CD und DVD Brenner mounted nicht (mit/ohne SCSI) |
 |
|
Das Installieren war ja fürchterlich leicht und sehr gut gemacht - ich denke bei mir bringt das kompilieren auch ein wenig, aber als ich an die einfachen Sachen gehe da scheitere ich gnadenlos 
(Kernel 2.6)
Ich habe erstmal einfach eine CD neulich rein (mount /dev/hdc /dvdwriter - klappt auf jedem bisherigen System von mir) und Gentoo sagt:
| Quote: | /dev/hdc: Input/output error
mount: /dev/hdc: can't read superblock |
oder jenachdem wie mein fstab Eintrag gerade aus sah was mit cannot read filesystem, bad superblock or to much filesystem mounted.
Dann bin ich schnell auf das Brenner Howto von Gentoo.org/.de gestoßen und habe die scsi-ide Emulation in den Kernel gebaut - nicht als Modul.
Beim Start sagt er nun folgendes:
| Quote: | Jan 14 21:49:12 linux /dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 p6 > p3
Jan 14 21:49:12 linux ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
Jan 14 21:49:12 linux scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Jan 14 21:49:12 linux Vendor: HL-DT-ST Model: DVDRAM GSA-4040B Rev: A301
Jan 14 21:49:12 linux Type: CD-ROM ANSI SCSI revision: 02
Jan 14 21:49:12 linux scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Jan 14 21:49:12 linux Vendor: LITE-ON Model: LTR-40125S Rev: ZS0P
Jan 14 21:49:12 linux Type: CD-ROM ANSI SCSI revision: 02
Jan 14 21:49:12 linux sr0: scsi3-mmc drive: 32x/32x writer dvd-ram cd/rw xa/form2 cdda tray
Jan 14 21:49:12 linux Uniform CD-ROM driver Revision: 3.12
Jan 14 21:49:12 linux Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Jan 14 21:49:12 linux sr1: scsi3-mmc drive: 106x/48x writer cd/rw xa/form2 cdda tray
Jan 14 21:49:12 linux Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
Jan 14 21:49:12 linux Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Jan 14 21:49:12 linux Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5 |
Ich habe eigentlich alles nach dem Howto gemacht außer das ich bei /etc/modules.d die scsi Datei erstellen musste und bei /etc/modules.autoload keinen Eintrag gemacht habe da ich den Support in den Kernel gebaut habe.
Bitte bitte helft mir - ich will nicht ohne CDs und DVDs weiterleben
EDIT:
dmesg loves you
| Quote: | Linux version 2.6.1 (root@linux) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #4 Tue Jan 13 17:00:43 UTC 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000fa980
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x3fff0000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030
ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0
ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
Building zonelist for node : 0
Kernel command line: root=/dev/hda1 hdc=ide-scsi hdd=ide-scsi
ide_setup: hdc=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 1533.661 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 1033440k/1048512k available (2500k kernel code, 14132k reserved, 880k data, 136k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3014.65 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 1800+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20031002
ACPI: IRQ 9 was Edge Triggered, setting to Level Triggerd
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1)
pty: 256 Unix98 ptys configured
request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
lp: driver loaded but no devices found
Linux agpgart interface v0.100 (c) Dave Jones
[drm:drm_init] *ERROR* Cannot initialize the agpgart module.
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
lp0: using parport0 (polling).
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xd800, 00:10:dc:96:a8:aa, IRQ 11.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: SAMSUNG SV1604N, ATA DISK drive
hdb: IC35L080AVVA07-0, ATA DISK drive
hdc: HL-DT-ST DVDRAM GSA-4040B, ATAPI CD/DVD-ROM drive
hdd: LITE-ON LTR-40125S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdb: max request size: 128KiB
hdb: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=65535/15/63
/dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 p6 > p3
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: DVDRAM GSA-4040B Rev: A301
Type: CD-ROM ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITE-ON Model: LTR-40125S Rev: ZS0P
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 32x/32x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 5, pci mem f8811f00
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 11, io base 0000e000
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 10, io base 0000e400
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 12, io base 0000e800
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
ALSA device list:
#0: C-Media PCI CMI8738-MC6 (model 55) at 0xec00, irq 10
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 136k freed
hub 3-0:1.0: new USB device on port 1, assigned address 2
Adding 979956k swap on /dev/hda3. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
drivers/usb/input/hid-core.c: ctrl urb status -104 received
drivers/usb/input/hid-core.c: timeout initializing reports
input: USB HID v1.00 Mouse [Logitech Inc. iFeel MouseMan] on usb-0000:00:10.1-1
spurious 8259A interrupt: IRQ7.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
end_request: I/O error, dev sr1, sector 0
Buffer I/O error on device sr1, logical block 0
end_request: I/O error, dev sr1, sector 64
Buffer I/O error on device sr1, logical block 8
end_request: I/O error, dev sr1, sector 0
FAT: unable to read boot sector
cdrom: open failed.
cdrom: open failed.
SCSI error : <0 0 0 0> return code = 0x8000002
Info fld=0x0, ILI Current sr0: sense = f0 25
ASC=64 ASCQ= 0
Raw sense data:0xf0 0x00 0x25 0x00 0x00 0x00 0x00 0x10 0x28 0x0a 0x01 0x20 0x64 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
end_request: I/O error, dev sr0, sector 0
Buffer I/O error on device sr0, logical block 0
SCSI error : <0 0 0 0> return code = 0x8000002
Info fld=0x10, ILI Current sr0: sense = f0 25
ASC=64 ASCQ= 0
Raw sense data:0xf0 0x00 0x25 0x00 0x00 0x00 0x10 0x10 0x28 0x0a 0x01 0x20 0x64 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
end_request: I/O error, dev sr0, sector 64
Buffer I/O error on device sr0, logical block 8
SCSI error : <0 0 0 0> return code = 0x8000002
Info fld=0x0, ILI Current sr0: sense = f0 25
ASC=64 ASCQ= 0
Raw sense data:0xf0 0x00 0x25 0x00 0x00 0x00 0x00 0x10 0x28 0x0a 0x01 0x20 0x64 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
end_request: I/O error, dev sr0, sector 0
FAT: unable to read boot sector
ndiswrapper version 0.4 loaded
wlan0: ndiswrapper ethernet device 00:06:25:4a:9c:1d
SCSI error : <0 0 0 0> return code = 0x8000002
Info fld=0x0, ILI Current sr0: sense = f0 25
ASC=64 ASCQ= 0
Raw sense data:0xf0 0x00 0x25 0x00 0x00 0x00 0x00 0x10 0x28 0x0a 0x01 0x20 0x64 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
end_request: I/O error, dev sr0, sector 0
Buffer I/O error on device sr0, logical block 0
SCSI error : <0 0 0 0> return code = 0x8000002
Info fld=0x10, ILI Current sr0: sense = f0 25
ASC=64 ASCQ= 0
Raw sense data:0xf0 0x00 0x25 0x00 0x00 0x00 0x10 0x10 0x28 0x0a 0x01 0x20 0x64 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
end_request: I/O error, dev sr0, sector 64
Buffer I/O error on device sr0, logical block 8
SCSI error : <0 0 0 0> return code = 0x8000002
Info fld=0x0, ILI Current sr0: sense = f0 25
ASC=64 ASCQ= 0
Raw sense data:0xf0 0x00 0x25 0x00 0x00 0x00 0x00 0x10 0x28 0x0a 0x01 0x20 0x64 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
end_request: I/O error, dev sr0, sector 0
FAT: unable to read boot sector
|
|
|
| Back to top |
|
 |
Pietschy
Apprentice
Joined: 25 Jul 2002
Posts: 237
|
| Posted: Wed Jan 14, 2004 10:35 pm Post subject: |
|
|
Öhm und du bist dir sicher, das die CD die du eingelegt hast in Ordnung ist ? (keine AudioCd, keine leerer Rohling oder sowas ?)
Dein Brenner sollte ausserdem hervorragend im ATAPI Mode funktionieren.
Deine Probleme scheinen ehher beim auslesen der CD liegen und weniger, wie du deine Laufwerke betreibst (IDE oder SCSI).
Ronny |
|
| Back to top |
|
|
eCaf
n00b
Joined: 25 Aug 2003
Posts: 26
|
| Posted: Sat Feb 07, 2004 1:17 pm Post subject: |
|
|
Ich habe zwei Fragen zu dem Thema:
1. Warum tritt dieser Fehler bei Audio-CDs auf, darf man die nicht mounten?
2. Warum kann ich seitdem ich auf Kernel 2.6 umgestellt habe das CD-ROM-Laufwerk von außen öffnen, obwohl die CDs gemountet sind?
_________________
Freundliche Grüße, eCaf |
|
| Back to top |
|
|
jay
l33t
Joined: 08 May 2002
Posts: 980
|
| Posted: Sat Feb 07, 2004 5:07 pm Post subject: |
|
|
| eCaf wrote: | Ich habe zwei Fragen zu dem Thema:
1. Warum tritt dieser Fehler bei Audio-CDs auf, darf man die nicht mounten?
2. Warum kann ich seitdem ich auf Kernel 2.6 umgestellt habe das CD-ROM-Laufwerk von außen öffnen, obwohl die CDs gemountet sind? |
1. Weil Audio-CDs kein Dateisystem besitzen.
2. Im 2.6 Kernel ist Mandrakes Supermount Patch schon drin.
_________________
Do you want your posessions identified? [ynq] (n) |
|
| Back to top |
|
|
Birnenpfluecker
Guru
Joined: 01 Sep 2003
Posts: 315
Location: Lage, Germany
|
| Posted: Sat Feb 07, 2004 5:43 pm Post subject: |
|
|
| hast du im kernel die richtigen filesystems kompiliert (iso9660 und udf)? Hört sich fast danach an als wenn er die filesysteme nicht kennt. Und poste mal bitte deine /etc/fstab |
|
| Back to top |
|
|
toskala
Advocate
Joined: 14 Dec 2002
Posts: 2080
Location: hamburg, germany
|
| Posted: Sat Feb 07, 2004 5:49 pm Post subject: |
|
|
poste bitte auch mal, was du im kernel eingebaut hast, an filesystem support.
und was sagt:
| Code: |
mount -t auto /dev/hdc /mountpoint
|
?
_________________
adopt an unanswered post
erst denken, dann posten |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Deutsches Forum (German)
