nowak07
n00b
Joined: 24 Jan 2004
Posts: 37
|
 Posted: Fri Mar 12, 2004 5:47 am Post subject: yet another insmod error |
 |
|
My system boots ok and works fine except forone or two minor problems including the long list of insmod errors.
Sorry for the long error message, but i've gone through a good number of posts but haven't found the answer to my problem.
| Code: | Linux version 2.4.20-gentoo-r6 (root@cdimage) (gcc version 3.2.3 20030422 (Gento
o Linux 1.4 3.2.3-r1, propolice)) #1 Sat Feb 14 02:29:00 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 AMI ) @ 0x000fa210
ACPI: RSDT (v001 AMIINT VIA_P6 00000.00016) @ 0x0fff0000
ACPI: FADT (v001 AMIINT VIA_P6 00000.00017) @ 0x0fff0030
ACPI: DSDT (v001 VIA APOLLO-P 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
Kernel command line: root=/dev/hda5
Initializing CPU#0
Detected 2000.223 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3984.58 BogoMIPS
Memory: 252480k/262080k available (1492k kernel code, 7168k reserved, -1804k dat
a, 100k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Proc Config support by ptb@it.uc3m.es
proc config counted 6528 bytes in names
proc config counted 711 bytes in value handles
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(R) CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20021122
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
ACPI-0511: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
PCI: Probing PCI hardware
PCI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off
'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 89
PCI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST340810A, ATA DISK drive
hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8160B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c0173344, I/O limit 4095Mb (mask 0xffffffff)
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Partition check:
/dev/ide/host0/bus0/target0/lun0:hda: dma_intr: status=0x51 { DriveReady SeekCo
mplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
p1 p2 < p5 p6 p7 >
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Equalizer1996: $Revision: 1.2.1 $ $Date: 1996/09/22 13:52:00 $ Simon Janes (simo
n@ncm.com)
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1410k freed
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
megaraid: v1.18 (Release Date: Thu Oct 11 15:02:53 EDT 2001)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
3ware Storage Controller device driver for Linux v1.02.00.031.
3w-xxxx: No cards with valid units found.
NCR53c406a: no available ports found
Red Hat/Adaptec aacraid driver, Feb 14 2004
Loading Adaptec I2O RAID: Version 2.4 Build 5
Detecting Adaptec I2O RAID controllers...
sim710: No NCR53C710 adapter found.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
hcd.c: ehci-hcd @ 00:10.3, VIA Technologies, Inc. USB 2.0
hcd.c: irq 5, pci mem d082ce00
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xe800, IRQ 11
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xe400, IRQ 11
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xe000, IRQ 5
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 100k freed
Adding Swap: 514040k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
inserting floppy driver for 2.4.20-gentoo-r6
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
end_request: I/O error, cmd 0 dev 02:00 (floppy), sector 0
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
PCI: Setting latency timer of device 00:11.5 to 64
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xd095df00, 00:30:4f:14:1f:6e, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
eth0: no IPv6 routers present |
Hope anyone can help. |
|
Installing Gentoo
