| View previous topic :: View next topic |
| Author |
Message |
panth0r
n00b
Joined: 16 Sep 2003
Posts: 7
Location: South Side of Chicago
|
 Posted: Wed Jun 30, 2004 11:41 am Post subject: CD burning |
 |
|
Gentoo doesn't act like it detects my cd-rom drives (they're just your basic drives, ata on a two-inch bus. It's not just a burning thing, straight up, it just decides not to detct my cd-rw and cd-rom drive. Thank you.
_________________
Water, water everywhere,
and all the boards did shrink;
Water, water everywhere,
nor any drop to drink. |
|
| Back to top |
|
 |
tuxedo
Tux's lil' helper
Joined: 27 Nov 2003
Posts: 78
Location: Winterthur, Switzerland
|
| Posted: Wed Jun 30, 2004 11:52 am Post subject: |
|
|
Are the drives recognized in the BIOS Setup? Did you compile support for IDE CD-ROMS (or for IDE in general) into your kernel? In case you did build it as a module: Did you load it?
_________________
[x] <-- Nail here for new monitor |
|
| Back to top |
|
|
-Craig-
Guru
Joined: 03 Jun 2004
Posts: 333
|
| Posted: Wed Jun 30, 2004 11:53 am Post subject: |
|
|
Give us your dmesg, cdrecord -scanbus and kernel .config!
Maybe your SCSI isn't installed correctly... |
|
| Back to top |
|
|
panth0r
n00b
Joined: 16 Sep 2003
Posts: 7
Location: South Side of Chicago
|
| Posted: Sun Jul 04, 2004 1:51 pm Post subject: |
|
|
Sorry I took so long. Yes, the drives are recognized in my BIOS and I did enable IDE ans SCSI emulation. The following is the output of cdrecord -scanbus:
| Code: | root@mymachine panth0r # cdrecord -scanbus
Cdrecord-Clone 2.01a28 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schillin
g
cdrecord: No such file or directory. Cannot open '/dev/pg*'. Cannot open SCSI dr
iver.
cdrecord: For possible targets try 'cdrecord -scanbus'. Make sure you are root.
cdrecord: For possible transport specifiers try 'cdrecord dev=help'.
root@mymachine panth0r # cdrecord dev=help
Cdrecord-Clone 2.01a28 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schillin
g
Supported SCSI transports for this platform:
Transport name: sg
Transport descr.: Generic transport independent SCSI
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: pg
Transport descr.: SCSI transport for ATAPI over Parallel Port
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport
Transp. layer ind.: ATAPI:
Target specifier: bus,target,lun
Target example: ATAPI:1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport using sg interface
Transp. layer ind.: ATA:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: RSCSI
Transport descr.: Remote SCSI
Transp. layer ind.: REMOTE:
Target specifier: rscsi@host:bus,target,lun
Target example: REMOTE:rscsi@host:1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
|
Again, thank you and sorry for taking so long to respond.
_________________
Water, water everywhere,
and all the boards did shrink;
Water, water everywhere,
nor any drop to drink. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Multimedia
