| View previous topic :: View next topic |
| Author |
Message |
gimbo²
n00b
Joined: 24 Jun 2003
Posts: 29
Location: venice - IT
|
 Posted: Mon Jul 05, 2004 9:44 am Post subject: [HW]e/o[Conf] : PCMCIA WiFi Trust con chipset Atheros AR5212 |
 |
|
ciao a tutti.
E' da un po' che provo a far funzionare una sceda Trust Speedshare turbo pro wireless PC-card ma non c'e' nulla da fare.
Dunque vi riassumo qualche dato:
Il portatile è un Acer Travelmate 525TE
| Code: | root # ifconfig
ath0 Link encap:Ethernet HWaddr 00:03:2F:15:C3:C2
inet addr:10.0.0.6 Bcast:10.0.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12344 errors:0 dropped:0 overruns:0 frame:0
TX packets:219 errors:2 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:199
RX bytes:920747 (899.1 Kb) TX bytes:22759 (22.2 Kb)
Interrupt:11 Memory:d8b84000-d8b94000
eth0 Link encap:Ethernet HWaddr 00:00:E2:42:0F:13
inet addr:10.0.0.6 Bcast:10.0.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:951 (951.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0xb000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4356 (4.2 Kb) TX bytes:4356 (4.2 Kb)
root # iwconfig ath0
ath0 IEEE 802.11 ESSID:"com"
Mode:Managed Frequency:2.412GHz Access Point: 00:0D:54:F9:59:62
Bit Rate:36Mb/s Tx-Power:off Sensitivity=0/3
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:53/94 Signal level:-42 dBm Noise level:-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root # iwlist ath0 scanning
ath0 Scan completed :
Cell 01 - Address: 00:0D:54:F9:59:62
Mode:Master
Encryption key:off
Quality:53/94 Signal level:-42 dBm Noise level:-95 dBm
Mode:Master
ESSID:"com"
Frequency:2.412GHz
Bit Rate:1Mb/s
Bit Rate:2Mb/s
Bit Rate:5Mb/s
Bit Rate:6Mb/s
Bit Rate:9Mb/s
Bit Rate:11Mb/s
Bit Rate:12Mb/s
Bit Rate:18Mb/s
Bit Rate:24Mb/s
Bit Rate:36Mb/s
Bit Rate:48Mb/s
Bit Rate:54Mb/s
root # ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=1.07 ms
64 bytes from 10.0.0.1: icmp_seq=3 ttl=64 time=1.09 ms
wrong data byte #20 should be 0x14 but was 0xa7
#8 8 9 a b c d e f 10 11 12 13 a7 fc 80 1 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27
#40 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37
64 bytes from 10.0.0.1: icmp_seq=4 ttl=64 time=1.07 ms
wrong data byte #20 should be 0x14 but was 0xa7
#8 8 9 a b c d e f 10 11 12 13 a7 fc 80 1 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27
#40 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37
64 bytes from 10.0.0.1: icmp_seq=6 ttl=64 time=1.08 ms
wrong data byte #20 should be 0x14 but was 0xa7
#8 8 9 a b c d e f 10 11 12 13 a7 fc 80 1 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27
#40 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37
64 bytes from 10.0.0.1: icmp_seq=7 ttl=64 time=1.02 ms
wrong data byte #20 should be 0x14 but was 0xa7
#8 8 9 a b c d e f 10 11 12 13 a7 fc 80 1 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27
#40 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37
64 bytes from 10.0.0.1: icmp_seq=8 ttl=64 time=1.03 ms
wrong data byte #12 should be 0xc but was 0x6b
#8 8 9 a b 6b 48 2c 6b 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27
#40 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 5f 5 80 1
--- 10.0.0.1 ping statistics ---
10 packets transmitted, 6 received, 40% packet loss, time 9003ms
rtt min/avg/max/mdev = 1.020/1.063/1.090/0.033 ms
root # route -v
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
[qui rimane ore e ore senza concludere nulla, intervenco con un Ctrl+c]
root # iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
ath0 IEEE 802.11 ESSID:"com"
Mode:Managed Frequency:2.412GHz Access Point: 00:0D:54:F9:59:62
Bit Rate:24Mb/s Tx-Power:off Sensitivity=0/3
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:51/94 Signal level:-44 dBm Noise level:-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root # lsmod
Module Size Used by
ali_agp 5092 -
yenta_socket 17668 -
ath_pci 39912 -
ath_hal 127760 -
wlan 58472 -
root # lspci
00:00.0 Host bridge: ALi Corporation M1621 (rev 05)
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (rev 01)
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 01)
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
00:0a.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c3)
00:11.0 Bridge: ALi Corporation M7101 PMU
00:13.0 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
00:13.1 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
00:14.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64)
06:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
e piu' precisamente
root # lspci -vvv
[...]
06:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Global Sun Technology Inc: Unknown device 7103
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 19000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
[...] |
la scheda viene riconosciiuta, qualche pacchetto ICMP arriva a corretto, molti (troppi) sono corrotti.
qulcuno ha idea di come si possa (e soprattutto SE si possa) risolvere il problema?
cordialmente
_________________
Gimbo²
Last edited by gimbo² on Mon Jul 05, 2004 1:10 pm; edited 2 times in total |
|
| Back to top |
|
 |
gimbo²
n00b
Joined: 24 Jun 2003
Posts: 29
Location: venice - IT
|
| Posted: Mon Jul 05, 2004 10:51 am Post subject: |
|
|
dimenticavo..
Wireless-tools v. 26-r1
Madwifi-driver v. 0.1_pre20040514
Dei Madwifi ho provato anche le versioni precedenti, ottenendo sempre lo stesso risultato 
_________________
Gimbo² |
|
| Back to top |
|
|
gimbo²
n00b
Joined: 24 Jun 2003
Posts: 29
Location: venice - IT
|
| Posted: Wed Jul 07, 2004 9:03 pm Post subject: |
|
|
 possibile che sia l'unico ad avere sta PCMCIA?! 
 -HELP-
_________________
Gimbo² |
|
| Back to top |
|
|
FonderiaDigitale
Veteran
Joined: 06 Nov 2003
Posts: 1710
Location: Rome, Italy
|
| Posted: Wed Jul 07, 2004 9:11 pm Post subject: |
|
|
per curiosita: dove l'hai presa e quanto l'hai pagata?
il driver e' qui: http://sourceforge.net/projects/madwifi/
_________________
Come disse un amico, i sistemisti sono un po' come gli artigiani per l'informatica 
|
|
| Back to top |
|
|
gimbo²
n00b
Joined: 24 Jun 2003
Posts: 29
Location: venice - IT
|
| Posted: Thu Jul 08, 2004 8:22 am Post subject: |
|
|
| FonderiaDigitale wrote: | | per curiosita: dove l'hai presa e quanto l'hai pagata? |
l'ho avuta in regalo, quidni non saprei proprio!
gia' lo so questo. Ho fatto l'emerge dei madwifi-driver
| gimbo² wrote: |
dimenticavo..
Wireless-tools v. 26-r1
Madwifi-driver v. 0.1_pre20040514
Dei Madwifi ho provato anche le versioni precedenti, ottenendo sempre lo stesso risultato |
_________________
Gimbo² |
|
| Back to top |
|
|
motaboy
Developer
Joined: 15 Dec 2003
Posts: 1483
|
| Posted: Thu Jul 08, 2004 8:47 am Post subject: |
|
|
Perché non fai una ricerca sulla loro mailing list e se non trovi niente non gli scrivi?
_________________
... |
|
| Back to top |
|
|
gimbo²
n00b
Joined: 24 Jun 2003
Posts: 29
Location: venice - IT
|
| Posted: Thu Jul 08, 2004 8:50 am Post subject: |
|
|
| motaboy wrote: | | Perché non fai una ricerca sulla loro mailing list e se non trovi niente non gli scrivi? |
a questo punto credo sia l'unica cosa da fare 
_________________
Gimbo² |
|
| Back to top |
|
|
motaboy
Developer
Joined: 15 Dec 2003
Posts: 1483
|
| Posted: Thu Jul 08, 2004 8:52 am Post subject: |
|
|
Secondo me ci metti meno che ad aspettare risposte che non arrivano...
PS. Io col modem GPRS quando pingavo avevo gli stessi errori che avevi tu, PERÓ i trasferimenti andavano senza nessun problema e non erano corrotti.
_________________
... |
|
| Back to top |
|
|
|
Forum italiano (Italian)
