Netzwerk geht nicht nach dem Booten

pmgas

Hallo

Ich habe ein lästiges Problem und keine AHnung wie ich das Lösen soll. Und zwar hab ich Gentoo neu aufgesetzt, nach dem Booten von der LiveCD geht alles einwandfrei, wenn ich anschließend rebooten dann geht auch alles, bis auf das Netzwerk.
Ok, ich mag ein Noob sein, es liegt aber NICHT daran das die Module nicht geladen sind ...

Ich habe alles im Kernel, hab 2 Interfaces, eine 3com Karte und ein Intel-onboardchip, es werden auch beide Interfaces gefunden und ich kann auch beiden eine IP geben, es ist auch überall ein Link vorhanden, allerdings hab ich kein Netzwerk (kann nichts pingen), obwohl ich alles genau wie auf der livecd gmacht hab .... Ist mir unerklärlich, denn nach dem Booten von Livecd gehts wieder.

Der einzige offensichtliche Unterschied zur Livecd ist, das sie auf der Livecd als module geladen werden und andernfalls eben fix im Kernel sind, aba i wüßt ned warums daran liegen sollte.

Hat wer eine Idee?

mfg peda

Minox · Posted: Mon Sep 06, 2004 6:55 pm Post subject:

Hi,
hast du das interface mit net-setup eth0 konfiguriert und mit rc-update add net.eth0 default in die runlevel aufgenommen?

MfG,
_________________
:!:

proud to be 100% M$ free :!:

pmgas · Posted: Mon Sep 06, 2004 7:08 pm Post subject: ja klar

hallo

danke für deine prompte antwort, habe ich aber alles gemacht.

ifconfig eth1 192.168.10.11 netmask 255.255.255.0 broadcast 192.168.10.255
route add default gw 192.168.10.254

link ist vorhanden, ich krieg auch keine fehlermeldung wenn ich das eingebe, bei der livecd funktioniert es genauso und hat eigentlich schon immer so funktioniert. Nur seit kurzem nicht mehr!!

ich krieg immer icmp - host unreachable zurück ...

obwohl es egal ist, ob ich das kabel an eth0 od. eth1 ansteck, überall selbes problem ..

_hephaistos_ · Posted: Mon Sep 06, 2004 7:22 pm Post subject: Re: ja klar

hallo,

wird beim booten das "netservice" gestartet?

sprich: wenn du eingeloggt bist, was sagt "/etc/init.d/net.<yourdev> status"??
dh: rc-update add net.<yourdev> default hast du ausgeführt...?

irgendwas verdächtiges sonst im log?

hth,
ciao

pmgas · Posted: Mon Sep 06, 2004 7:32 pm Post subject: nix verdächtiges

ja, ist alles gestartet

Das Netzwerkinterface eth1 hat auch eine IP und wird bei ifconfig auch angezeigt mit dieser IP. Und auch an diesem Interface ist das Netzwerkkabel angeschlossen, ist mir total unerklärlich!

Das Problem ist ja auch, das ich nur über ssh arbeiten kann, also derzeit ist von CD gestartet und i mag ned die 100km zum Server fahrn! ;-)

So wirkli was brauchbares hätt ich nicht gsehn in den logfiles.

Sep 6 18:21:16 www syslog-ng[5206]: syslog-ng version 1.6.4 starting
Sep 6 18:21:16 www syslog-ng[5206]: Changing permissions on special file /dev/tty12
Sep 6 18:21:16 www Linux version 2.6.8.1 (root@livecd) (gcc version 3.3.3 20040412 (Gentoo Linux 3.3.3-r6, ssp-3.3.2-2, pie-8.7.6)) #1 SMP Mon Sep 6 19:47:56 CEST 2004
Sep 6 18:21:16 www BIOS-provided physical RAM map:
Sep 6 18:21:16 www BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
Sep 6 18:21:16 www BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
Sep 6 18:21:16 www BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Sep 6 18:21:16 www BIOS-e820: 0000000000100000 - 000000001fff8000 (usable)
Sep 6 18:21:16 www BIOS-e820: 000000001fff8000 - 0000000020000000 (reserved)
Sep 6 18:21:16 www 511MB LOWMEM available.
Sep 6 18:21:16 www found SMP MP-table at 000f8000
Sep 6 18:21:16 www On node 0 totalpages: 131064
Sep 6 18:21:16 www DMA zone: 4096 pages, LIFO batch:1
Sep 6 18:21:16 www Normal zone: 126968 pages, LIFO batch:16
Sep 6 18:21:16 www HighMem zone: 0 pages, LIFO batch:1
Sep 6 18:21:16 www DMI 2.0 present.
Sep 6 18:21:16 www ACPI disabled because your bios is from 98 and too old
Sep 6 18:21:16 www You can enable it with acpi=force
Sep 6 18:21:16 www Intel MultiProcessor Specification v1.4
Sep 6 18:21:16 www Virtual Wire compatibility mode.
Sep 6 18:21:16 www OEM ID: ACER Product ID: M9D APIC at: 0xFEE00000
Sep 6 18:21:16 www Processor #0 6:5 APIC version 17
Sep 6 18:21:16 www Processor #1 6:5 APIC version 17
Sep 6 18:21:16 www I/O APIC #2 Version 17 at 0xFEC00000.
Sep 6 18:21:16 www Enabling APIC mode: Flat. Using 1 I/O APICs
Sep 6 18:21:16 www Processors: 2
Sep 6 18:21:16 www Built 1 zonelists
Sep 6 18:21:16 www Kernel command line: root=/dev/sda9
Sep 6 18:21:16 www Initializing CPU#0
Sep 6 18:21:16 www PID hash table entries: 2048 (order 11: 16384 bytes)
Sep 6 18:21:16 www Detected 350.859 MHz processor.
Sep 6 18:21:16 www Using tsc for high-res timesource
Sep 6 18:21:16 www Console: colour VGA+ 80x25
Sep 6 18:21:16 www Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Sep 6 18:21:16 www Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Sep 6 18:21:16 www Memory: 513032k/524256k available (3348k kernel code, 10432k reserved, 1239k data, 348k init, 0k highmem)
Sep 6 18:21:16 www Checking if this processor honours the WP bit even in supervisor mode... Ok.
Sep 6 18:21:16 www Calibrating delay loop... 692.22 BogoMIPS
Sep 6 18:21:16 www Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Sep 6 18:21:16 www CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
Sep 6 18:21:16 www CPU: After vendor identify, caps: 0183fbff 00000000 00000000 00000000
Sep 6 18:21:16 www CPU: L1 I cache: 16K, L1 D cache: 16K
Sep 6 18:21:16 www CPU: L2 cache: 512K
Sep 6 18:21:16 www CPU: After all inits, caps: 0183fbff 00000000 00000000 00000040
Sep 6 18:21:16 www Intel machine check architecture supported.
Sep 6 18:21:16 www Intel machine check reporting enabled on CPU#0.
Sep 6 18:21:16 www Enabling fast FPU save and restore... done.
Sep 6 18:21:16 www Checking 'hlt' instruction... OK.
Sep 6 18:21:16 www CPU0: Intel Pentium II (Deschutes) stepping 02
Sep 6 18:21:16 www per-CPU timeslice cutoff: 1463.72 usecs.
Sep 6 18:21:16 www task migration cache decay timeout: 2 msecs.
Sep 6 18:21:16 www enabled ExtINT on CPU#0
Sep 6 18:21:16 www ESR value before enabling vector: 00000000
Sep 6 18:21:16 www ESR value after enabling vector: 00000000
Sep 6 18:21:16 www Booting processor 1/1 eip 2000
Sep 6 18:21:16 www Initializing CPU#1
Sep 6 18:21:16 www masked ExtINT on CPU#1
Sep 6 18:21:16 www ESR value before enabling vector: 00000000
Sep 6 18:21:16 www ESR value after enabling vector: 00000000
Sep 6 18:21:16 www Calibrating delay loop... 700.41 BogoMIPS
Sep 6 18:21:16 www CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
Sep 6 18:21:16 www CPU: After vendor identify, caps: 0183fbff 00000000 00000000 00000000
Sep 6 18:21:16 www CPU: L1 I cache: 16K, L1 D cache: 16K
Sep 6 18:21:16 www CPU: L2 cache: 512K
Sep 6 18:21:16 www CPU: After all inits, caps: 0183fbff 00000000 00000000 00000040
Sep 6 18:21:16 www Intel machine check architecture supported.
Sep 6 18:21:16 www Intel machine check reporting enabled on CPU#1.
Sep 6 18:21:16 www CPU1: Intel Pentium II (Deschutes) stepping 02
Sep 6 18:21:16 www Total of 2 processors activated (1392.64 BogoMIPS).
Sep 6 18:21:16 www ENABLING IO-APIC IRQs
Sep 6 18:21:16 www Setting 2 in the phys_id_present_map
Sep 6 18:21:16 www ...changing IO-APIC physical APIC ID to 2 ... ok.
Sep 6 18:21:16 www init IO_APIC IRQs
Sep 6 18:21:16 www IO-APIC (apicid-pin) 2-0, 2-17, 2-18, 2-20, 2-21 not connected.
Sep 6 18:21:16 www ..TIMER: vector=0x31 pin1=2 pin2=-1
Sep 6 18:21:16 www number of MP IRQ sources: 20.
Sep 6 18:21:16 www number of IO-APIC #2 registers: 24.
Sep 6 18:21:16 www testing the IO APIC.......................
Sep 6 18:21:16 www IO APIC #2......
Sep 6 18:21:16 www .... register #00: 02000000
Sep 6 18:21:16 www ....... : physical APIC id: 02
Sep 6 18:21:16 www ....... : Delivery Type: 0
Sep 6 18:21:16 www ....... : LTS : 0
Sep 6 18:21:16 www .... register #01: 00170011
Sep 6 18:21:16 www ....... : max redirection entries: 0017
Sep 6 18:21:16 www ....... : PRQ implemented: 0
Sep 6 18:21:16 www ....... : IO APIC version: 0011
Sep 6 18:21:16 www .... register #02: 00000000
Sep 6 18:21:16 www ....... : arbitration: 00
Sep 6 18:21:16 www .... IRQ redirection table:
Sep 6 18:21:16 www NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
Sep 6 18:21:16 www 00 000 00 1 0 0 0 0 0 0 00
Sep 6 18:21:16 www 01 001 01 0 0 0 0 0 1 1 39
Sep 6 18:21:16 www 02 001 01 0 0 0 0 0 1 1 31
Sep 6 18:21:16 www 03 001 01 0 0 0 0 0 1 1 41
Sep 6 18:21:16 www 04 001 01 0 0 0 0 0 1 1 49
Sep 6 18:21:16 www 05 001 01 0 0 0 0 0 1 1 51
Sep 6 18:21:16 www 06 001 01 0 0 0 0 0 1 1 59
Sep 6 18:21:16 www 07 001 01 0 0 0 0 0 1 1 61
Sep 6 18:21:16 www 08 001 01 0 0 0 0 0 1 1 69
Sep 6 18:21:16 www 09 001 01 0 0 0 0 0 1 1 71
Sep 6 18:21:16 www 0a 001 01 0 0 0 0 0 1 1 79
Sep 6 18:21:16 www 0b 001 01 0 0 0 0 0 1 1 81
Sep 6 18:21:16 www 0c 001 01 0 0 0 0 0 1 1 89
Sep 6 18:21:16 www 0d 001 01 0 0 0 0 0 1 1 91
Sep 6 18:21:16 www 0e 001 01 0 0 0 0 0 1 1 99
Sep 6 18:21:16 www 0f 001 01 0 0 0 0 0 1 1 A1
Sep 6 18:21:16 www 10 001 01 1 1 0 1 0 1 1 A9
Sep 6 18:21:16 www 11 000 00 1 0 0 0 0 0 0 00
Sep 6 18:21:16 www 12 000 00 1 0 0 0 0 0 0 00
Sep 6 18:21:16 www 13 001 01 1 1 0 1 0 1 1 B1
Sep 6 18:21:16 www 14 000 00 1 0 0 0 0 0 0 00
Sep 6 18:21:16 www 15 000 00 1 0 0 0 0 0 0 00
Sep 6 18:21:16 www 16 001 01 1 1 0 1 0 1 1 B9
Sep 6 18:21:16 www 17 001 01 1 1 0 1 0 1 1 C1
Sep 6 18:21:16 www IRQ to pin mappings:
Sep 6 18:21:16 www IRQ0 -> 0:2
Sep 6 18:21:16 www IRQ1 -> 0:1
Sep 6 18:21:16 www IRQ3 -> 0:3
Sep 6 18:21:16 www IRQ4 -> 0:4
Sep 6 18:21:16 www IRQ5 -> 0:5
Sep 6 18:21:16 www IRQ6 -> 0:6
Sep 6 18:21:16 www IRQ7 -> 0:7
Sep 6 18:21:16 www IRQ8 -> 0:8
Sep 6 18:21:16 www IRQ9 -> 0:9
Sep 6 18:21:16 www IRQ10 -> 0:10
Sep 6 18:21:16 www IRQ11 -> 0:11
Sep 6 18:21:16 www IRQ12 -> 0:12
Sep 6 18:21:16 www IRQ13 -> 0:13
Sep 6 18:21:16 www IRQ14 -> 0:14
Sep 6 18:21:16 www IRQ15 -> 0:15
Sep 6 18:21:16 www IRQ16 -> 0:16
Sep 6 18:21:16 www IRQ19 -> 0:19
Sep 6 18:21:16 www IRQ22 -> 0:22
Sep 6 18:21:16 www IRQ23 -> 0:23
Sep 6 18:21:16 www .................................... done.
Sep 6 18:21:16 www Using local APIC timer interrupts.
Sep 6 18:21:16 www calibrating APIC timer ...
Sep 6 18:21:16 www ..... CPU clock speed is 350.0729 MHz.
Sep 6 18:21:16 www ..... host bus clock speed is 100.0208 MHz.
Sep 6 18:21:16 www checking TSC synchronization across 2 CPUs: passed.
Sep 6 18:21:16 www Brought up 2 CPUs
Sep 6 18:21:16 www CPU0: online
Sep 6 18:21:16 www domain 0: span 03
Sep 6 18:21:16 www groups: 01 02
Sep 6 18:21:16 www CPU1: online
Sep 6 18:21:16 www domain 0: span 03
Sep 6 18:21:16 www groups: 02 01
Sep 6 18:21:16 www NET: Registered protocol family 16
Sep 6 18:21:16 www PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
Sep 6 18:21:16 www PCI: Using configuration type 1
Sep 6 18:21:16 www mtrr: v2.0 (20020519)
Sep 6 18:21:16 www mtrr: your CPUs had inconsistent fixed MTRR settings
Sep 6 18:21:16 www mtrr: probably your BIOS does not setup all CPUs.
Sep 6 18:21:16 www mtrr: corrected configuration.
Sep 6 18:21:16 www Linux Plug and Play Support v0.97 (c) Adam Belay
Sep 6 18:21:16 www SCSI subsystem initialized
Sep 6 18:21:16 www PCI: Probing PCI hardware
Sep 6 18:21:16 www PCI: Probing PCI hardware (bus 00)
Sep 6 18:21:16 www PCI->APIC IRQ transform: (B0,I7,P3) -> 19
Sep 6 18:21:16 www PCI->APIC IRQ transform: (B0,I12,P0) -> 16
Sep 6 18:21:16 www PCI->APIC IRQ transform: (B0,I16,P0) -> 19
Sep 6 18:21:16 www PCI->APIC IRQ transform: (B1,I6,P0) -> 22
Sep 6 18:21:16 www PCI->APIC IRQ transform: (B1,I10,P0) -> 23
Sep 6 18:21:16 www vesafb: probe of vesafb0 failed with error -6
Sep 6 18:21:16 www Machine check exception polling timer started.
Sep 6 18:21:16 www apm: BIOS not found.
Sep 6 18:21:16 www Starting balanced_irq
Sep 6 18:21:16 www devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
Sep 6 18:21:16 www devfs: devfs_debug: 0x0
Sep 6 18:21:16 www devfs: boot_options: 0x1
Sep 6 18:21:16 www Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Sep 6 18:21:16 www udf: registering filesystem
Sep 6 18:21:16 www SGI XFS with large block numbers, no debug enabled
Sep 6 18:21:16 www Initializing Cryptographic API
Sep 6 18:21:16 www Limiting direct PCI/PCI transfers.
Sep 6 18:21:16 www isapnp: Scanning for PnP cards...
Sep 6 18:21:16 www isapnp: No Plug & Play device found
Sep 6 18:21:16 www Real Time Clock Driver v1.12
Sep 6 18:21:16 www Non-volatile memory driver v1.2
Sep 6 18:21:16 www Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
Sep 6 18:21:16 www ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Sep 6 18:21:16 www ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Sep 6 18:21:16 www Using anticipatory io scheduler
Sep 6 18:21:16 www Floppy drive(s): fd0 is 1.44M
Sep 6 18:21:16 www FDC 0 is a post-1991 82077
Sep 6 18:21:16 www RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Sep 6 18:21:16 www loop: loaded (max 8 devices)
Sep 6 18:21:16 www dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15
Sep 6 18:21:16 www FW Version=$Version$
Sep 6 18:21:16 www 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
Sep 6 18:21:16 www 0000:00:0c.0: 3Com PCI 3c905C Tornado at 0xa000. Vers LK1.1.19
Sep 6 18:21:16 www eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
Sep 6 18:21:16 www eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
Sep 6 18:21:16 www eth1: 0000:00:10.0, 00:00:E2:1F:22:95, IRQ 19.
Sep 6 18:21:16 www Receiver lock-up bug exists -- enabling work-around.
Sep 6 18:21:16 www Board assembly 097176-026, Physical connectors present: RJ45
Sep 6 18:21:16 www Primary interface chip i82555 PHY #1.
Sep 6 18:21:16 www General self-test: passed.
Sep 6 18:21:16 www Serial sub-system self-test: passed.
Sep 6 18:21:16 www Internal registers self-test: passed.
Sep 6 18:21:16 www ROM checksum self-test: passed (0x24c9f043).
Sep 6 18:21:16 www Receiver lock-up workaround activated.
Sep 6 18:21:16 www Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Sep 6 18:21:16 www ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Sep 6 18:21:16 www PIIX4: IDE controller at PCI slot 0000:00:07.1
Sep 6 18:21:16 www PIIX4: chipset revision 1
Sep 6 18:21:16 www PIIX4: not 100% native mode: will probe irqs later
Sep 6 18:21:16 www ide0: BM-DMA at 0xa870-0xa877, BIOS settings: hda:pio, hdb:pio
Sep 6 18:21:16 www ide-floppy driver 0.99.newide
Sep 6 18:21:16 www Red Hat/Adaptec aacraid driver (1.1.2-lk2 Sep 6 2004)
Sep 6 18:21:16 www sym53c416.c: Version 1.0.0-ac
Sep 6 18:21:16 www sym0: <895> rev 0x1 at pci 0000:01:06.0 irq 22
Sep 6 18:21:16 www sym0: Symbios NVRAM, ID 7, Fast-40, SE, parity checking
Sep 6 18:21:16 www sym0: SCSI BUS has been reset.
Sep 6 18:21:16 www sym0: SCSI BUS mode change from SE to SE.
Sep 6 18:21:16 www scsi2 : sym-2.1.18j
Sep 6 18:21:16 www sym0: SCSI BUS has been reset.
Sep 6 18:21:16 www Vendor: FUJITSU Model: MAB3045SC Rev: 0108
Sep 6 18:21:16 www Type: Direct-Access ANSI SCSI revision: 02
Sep 6 18:21:16 www sym0:0:0: tagged command queuing enabled, command queue depth 16.
Sep 6 18:21:16 www scsi(2:0:0:0): Beginning Domain Validation
Sep 6 18:21:16 www sym0:0: wide asynchronous.
Sep 6 18:21:16 www sym0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
Sep 6 18:21:16 www scsi(2:0:0:0): Domain Validation skipping write tests
Sep 6 18:21:16 www scsi(2:0:0:0): Ending Domain Validation
Sep 6 18:21:16 www Vendor: FUJITSU Model: MAB3045SC Rev: 0108
Sep 6 18:21:16 www Type: Direct-Access ANSI SCSI revision: 02
Sep 6 18:21:16 www sym0:1:0: tagged command queuing enabled, command queue depth 16.
Sep 6 18:21:16 www scsi(2:0:1:0): Beginning Domain Validation
Sep 6 18:21:16 www sym0:1: wide asynchronous.
Sep 6 18:21:16 www sym0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
Sep 6 18:21:16 www scsi(2:0:1:0): Domain Validation skipping write tests
Sep 6 18:21:16 www scsi(2:0:1:0): Ending Domain Validation
Sep 6 18:21:16 www Vendor: HP Model: C1537A Rev: L708
Sep 6 18:21:16 www Type: Sequential-Access ANSI SCSI revision: 02
Sep 6 18:21:16 www scsi(2:0:3:0): Beginning Domain Validation
Sep 6 18:21:16 www sym0:3: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 31)
Sep 6 18:21:16 www scsi(2:0:3:0): Domain Validation skipping write tests
Sep 6 18:21:16 www scsi(2:0:3:0): Ending Domain Validation
Sep 6 18:21:16 www Vendor: FUJITSU Model: SAF-TE PROCESSOR Rev: 3.07
Sep 6 18:21:16 www Type: Processor ANSI SCSI revision: 02
Sep 6 18:21:16 www scsi(2:0:6:0): Beginning Domain Validation
Sep 6 18:21:16 www sym0: unexpected disconnect
Sep 6 18:21:16 www scsi(2:0:6:0): Ending Domain Validation
Sep 6 18:21:16 www sym1: <895> rev 0x1 at pci 0000:01:0a.0 irq 23
Sep 6 18:21:16 www sym1: Symbios NVRAM, ID 7, Fast-40, SE, parity checking
Sep 6 18:21:16 www sym1: SCSI BUS has been reset.
Sep 6 18:21:16 www sym1: SCSI BUS mode change from SE to SE.
Sep 6 18:21:16 www scsi3 : sym-2.1.18j
Sep 6 18:21:16 www sym1: SCSI BUS has been reset.
Sep 6 18:21:16 www Vendor: FUJITSU Model: MAB3045SC Rev: 0108
Sep 6 18:21:16 www Type: Direct-Access ANSI SCSI revision: 02
Sep 6 18:21:16 www sym1:0:0: tagged command queuing enabled, command queue depth 16.
Sep 6 18:21:16 www scsi(3:0:0:0): Beginning Domain Validation
Sep 6 18:21:16 www sym1:0: wide asynchronous.
Sep 6 18:21:16 www sym1:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
Sep 6 18:21:16 www scsi(3:0:0:0): Domain Validation skipping write tests
Sep 6 18:21:16 www scsi(3:0:0:0): Ending Domain Validation
Sep 6 18:21:16 www Vendor: FUJITSU Model: MAB3045SC Rev: 0108
Sep 6 18:21:16 www Type: Direct-Access ANSI SCSI revision: 02
Sep 6 18:21:16 www sym1:1:0: tagged command queuing enabled, command queue depth 16.
Sep 6 18:21:16 www scsi(3:0:1:0): Beginning Domain Validation
Sep 6 18:21:16 www sym1:1: wide asynchronous.
Sep 6 18:21:16 www sym1:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
Sep 6 18:21:16 www scsi(3:0:1:0): Domain Validation skipping write tests
Sep 6 18:21:16 www scsi(3:0:1:0): Ending Domain Validation
Sep 6 18:21:16 www Vendor: FUJITSU Model: SAF-TE PROCESSOR Rev: 3.07
Sep 6 18:21:16 www Type: Processor ANSI SCSI revision: 02
Sep 6 18:21:16 www scsi(3:0:6:0): Beginning Domain Validation
Sep 6 18:21:16 www sym1: unexpected disconnect
Sep 6 18:21:16 www scsi(3:0:6:0): Ending Domain Validation
Sep 6 18:21:16 www Failed initialization of WD-7000 SCSI card!
Sep 6 18:21:16 www 3ware Storage Controller device driver for Linux v1.26.00.039.
Sep 6 18:21:16 www 3w-xxxx: No cards found.
Sep 6 18:21:16 www st: Version 20040403, fixed bufsize 32768, s/g segs 256
Sep 6 18:21:16 www Attached scsi tape st0 at scsi2, channel 0, id 3, lun 0
Sep 6 18:21:16 www st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575
Sep 6 18:21:16 www osst :I: Tape driver with OnStream support version 0.99.1
Sep 6 18:21:16 www osst :I: $Id: osst.c,v 1.70 2003/12/23 14:22:12 wriede Exp $
Sep 6 18:21:16 www SCSI device sda: 8895370 512-byte hdwr sectors (4554 MB)
Sep 6 18:21:16 www SCSI device sda: drive cache: write through
Sep 6 18:21:16 www /dev/scsi/host2/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 >
Sep 6 18:21:16 www Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Sep 6 18:21:16 www SCSI device sdb: 8895370 512-byte hdwr sectors (4554 MB)
Sep 6 18:21:16 www SCSI device sdb: drive cache: write through
Sep 6 18:21:16 www /dev/scsi/host2/bus0/target1/lun0: p1 p2
Sep 6 18:21:16 www Attached scsi disk sdb at scsi2, channel 0, id 1, lun 0
Sep 6 18:21:16 www SCSI device sdc: 8895370 512-byte hdwr sectors (4554 MB)
Sep 6 18:21:16 www SCSI device sdc: drive cache: write through
Sep 6 18:21:16 www /dev/scsi/host3/bus0/target0/lun0:
Sep 6 18:21:16 www Attached scsi disk sdc at scsi3, channel 0, id 0, lun 0
Sep 6 18:21:16 www SCSI device sdd: 8895370 512-byte hdwr sectors (4554 MB)
Sep 6 18:21:16 www SCSI device sdd: drive cache: write through
Sep 6 18:21:16 www /dev/scsi/host3/bus0/target1/lun0:
Sep 6 18:21:16 www Attached scsi disk sdd at scsi3, channel 0, id 1, lun 0
Sep 6 18:21:16 www Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0
Sep 6 18:21:16 www Attached scsi generic sg1 at scsi2, channel 0, id 1, lun 0, type 0
Sep 6 18:21:16 www Attached scsi generic sg2 at scsi2, channel 0, id 3, lun 0, type 1
Sep 6 18:21:16 www Attached scsi generic sg3 at scsi2, channel 0, id 6, lun 0, type 3
Sep 6 18:21:16 www Attached scsi generic sg4 at scsi3, channel 0, id 0, lun 0, type 0
Sep 6 18:21:16 www Attached scsi generic sg5 at scsi3, channel 0, id 1, lun 0, type 0
Sep 6 18:21:16 www Attached scsi generic sg6 at scsi3, channel 0, id 6, lun 0, type 3
Sep 6 18:21:16 www mice: PS/2 mouse device common for all mice
Sep 6 18:21:16 www serio: i8042 AUX port at 0x60,0x64 irq 12
Sep 6 18:21:16 www input: PS/2 Generic Mouse on isa0060/serio1
Sep 6 18:21:16 www serio: i8042 KBD port at 0x60,0x64 irq 1
Sep 6 18:21:16 www input: AT Translated Set 2 keyboard on isa0060/serio0
Sep 6 18:21:16 www device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
Sep 6 18:21:16 www NET: Registered protocol family 2
Sep 6 18:21:16 www IP: routing cache hash table of 4096 buckets, 32Kbytes
Sep 6 18:21:16 www TCP: Hash tables configured (established 32768 bind 32768)
Sep 6 18:21:16 www NET: Registered protocol family 1
Sep 6 18:21:16 www NET: Registered protocol family 17
Sep 6 18:21:16 www ReiserFS: sda9: found reiserfs format "3.6" with standard journal
Sep 6 18:21:16 www ReiserFS: sda9: using ordered data mode
Sep 6 18:21:16 www ReiserFS: sda9: journal params: device sda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Sep 6 18:21:16 www ReiserFS: sda9: checking transaction log (sda9)
Sep 6 18:21:16 www ReiserFS: sda9: journal-1153: found in header: first_unflushed_offset 1899, last_flushed_trans_id 2133
Sep 6 18:21:16 www ReiserFS: sda9: journal-1206: Starting replay from offset 9165460211563, trans_id 0
Sep 6 18:21:16 www ReiserFS: sda9: journal-1299: Setting newest_mount_id to 13
Sep 6 18:21:16 www ReiserFS: sda9: Using r5 hash to sort names
Sep 6 18:21:16 www VFS: Mounted root (reiserfs filesystem) readonly.
Sep 6 18:21:16 www Mounted devfs on /dev
Sep 6 18:21:16 www Freeing unused kernel memory: 348k freed
Sep 6 18:21:16 www Adding 782400k swap on /dev/sda2. Priority:-1 extents:1
Sep 6 18:21:16 www ReiserFS: sda5: found reiserfs format "3.6" with standard journal
Sep 6 18:21:16 www ReiserFS: sda5: warning: CONFIG_REISERFS_CHECK is set ON
Sep 6 18:21:16 www ReiserFS: sda5: warning: - it is slow mode for debugging.
Sep 6 18:21:16 www ReiserFS: sda5: using ordered data mode
Sep 6 18:21:16 www ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Sep 6 18:21:16 www ReiserFS: sda5: checking transaction log (sda5)
Sep 6 18:21:16 www ReiserFS: sda5: journal-1153: found in header: first_unflushed_offset 1583, last_flushed_trans_id 350
Sep 6 18:21:16 www ReiserFS: sda5: journal-1206: Starting replay from offset 1507533522479, trans_id 0
Sep 6 18:21:16 www ReiserFS: sda5: journal-1299: Setting newest_mount_id to 13
Sep 6 18:21:16 www ReiserFS: sda5: Using r5 hash to sort names
Sep 6 18:21:16 www ReiserFS: sda6: found reiserfs format "3.6" with standard journal
Sep 6 18:21:16 www ReiserFS: sda6: warning: CONFIG_REISERFS_CHECK is set ON
Sep 6 18:21:16 www ReiserFS: sda6: warning: - it is slow mode for debugging.
Sep 6 18:21:16 www ReiserFS: sda6: using ordered data mode
Sep 6 18:21:16 www ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Sep 6 18:21:16 www ReiserFS: sda6: checking transaction log (sda6)
Sep 6 18:21:16 www ReiserFS: sda6: journal-1153: found in header: first_unflushed_offset 5463, last_flushed_trans_id 1004
Sep 6 18:21:16 www ReiserFS: sda6: journal-1206: Starting replay from offset 4316442137943, trans_id 0
Sep 6 18:21:16 www ReiserFS: sda6: journal-1299: Setting newest_mount_id to 13
Sep 6 18:21:16 www ReiserFS: sda6: Using r5 hash to sort names
Sep 6 18:21:16 www ReiserFS: sda7: found reiserfs format "3.6" with standard journal
Sep 6 18:21:16 www ReiserFS: sda7: warning: CONFIG_REISERFS_CHECK is set ON
Sep 6 18:21:16 www ReiserFS: sda7: warning: - it is slow mode for debugging.
Sep 6 18:21:16 www ReiserFS: sda7: using ordered data mode
Sep 6 18:21:16 www ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Sep 6 18:21:16 www ReiserFS: sda7: checking transaction log (sda7)
Sep 6 18:21:16 www ReiserFS: sda7: journal-1153: found in header: first_unflushed_offset 6596, last_flushed_trans_id 1259
Sep 6 18:21:16 www ReiserFS: sda7: journal-1206: Starting replay from offset 5411658799556, trans_id 0
Sep 6 18:21:16 www ReiserFS: sda7: journal-1299: Setting newest_mount_id to 13
Sep 6 18:21:16 www ReiserFS: sda7: Using r5 hash to sort names
Sep 6 18:21:16 www ReiserFS: sda8: found reiserfs format "3.6" with standard journal
Sep 6 18:21:16 www ReiserFS: sda8: warning: CONFIG_REISERFS_CHECK is set ON
Sep 6 18:21:16 www ReiserFS: sda8: warning: - it is slow mode for debugging.
Sep 6 18:21:16 www ReiserFS: sda8: using ordered data mode
Sep 6 18:21:16 www ReiserFS: sda8: journal params: device sda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Sep 6 18:21:16 www ReiserFS: sda8: checking transaction log (sda8)
Sep 6 18:21:16 www ReiserFS: sda8: journal-1153: found in header: first_unflushed_offset 32, last_flushed_trans_id 19
Sep 6 18:21:16 www ReiserFS: sda8: journal-1206: Starting replay from offset 85899345952, trans_id 0
Sep 6 18:21:16 www ReiserFS: sda8: journal-1299: Setting newest_mount_id to 13
Sep 6 18:21:16 www ReiserFS: sda8: Using r5 hash to sort names
Sep 6 18:21:18 www sshd[5372]: Server listening on 0.0.0.0 port 22.
Sep 6 18:21:18 www cron[5415]: (CRON) STARTUP (fork ok)

SirPreme · n00b Joined: 19 Aug 2004 Posts: 25

Ist das da zufällig auchs so, dass es total lange dauert, bis das Login-Fenster erscheint?

Ich hatte das Problem, bei mir musste ich (glaube ich) in die /etc/hosts meinen Router (also Hostnamen und Adresse) eintragen. Ich hatte mal ne Seite, wo das erklärt wird - wenns gar nicht klappt, such ich die dir mal raus..