| View previous topic :: View next topic |
| Author |
Message |
ISN004
n00b
Joined: 07 Sep 2004
Posts: 23
|
 Posted: Thu Oct 14, 2004 8:37 am Post subject: Yet another Alsa Problem (Like you guys don't see enough) |
 |
|
Hi everyone-
I've spent the last three days trying to get ALSA working on my system (AMD64 3200+ w/ an Asus K8V motherboard and Sound Blaster Live Video card) but to no avail. Originally I had the emu10k1 driver enabled in the kernel. With that as the case, I was able to follow all the steps in the gentoo ALSA howto, right up to the point where I was supposed to be able to play sound (unmuting channels, etc) There was, unfortunately, no sound to be found. I even looked at it with alsamixer to make sure I wasn't missing anything. So, I then decided to recompile my kernel and keep the drivers as modules. That was I can use alsaconf, and hope it works. I recompiled and still it's not working. I'm running the 2.6.8-gentoo-r4 kernel.
Here is my dmesg. Note that in the ALSA device list it says "no soundcards found":
| Code: | init)
Calibrating delay loop... 4308.99 BogoMIPS
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
init init/main.c:657
init init/main.c:670
smp_boot_cpus arch/x86_64/kernel/smpboot.c:741
Using local APIC NMI watchdog using perfctr0
smp_boot_cpus arch/x86_64/kernel/smpboot.c:745
smp_boot_cpus arch/x86_64/kernel/smpboot.c:751
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 00
smp_boot_cpus arch/x86_64/kernel/smpboot.c:757
per-CPU timeslice cutoff: 512.14 usecs.
task migration cache decay timeout: 1 msecs.
smp_boot_cpus arch/x86_64/kernel/smpboot.c:762
smp_boot_cpus arch/x86_64/kernel/smpboot.c:770
smp_boot_cpus arch/x86_64/kernel/smpboot.c:811
Getting VERSION: 40010
Getting VERSION: 40010
Getting ID: 0
Getting ID: f000000
Getting LVT0: 700
Getting LVT1: 400
smp_boot_cpus arch/x86_64/kernel/smpboot.c:815
smp_boot_cpus arch/x86_64/kernel/smpboot.c:830
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 1
smp_boot_cpus arch/x86_64/kernel/smpboot.c:863
Before bogomips.
Only one processor found.
smp_boot_cpus arch/x86_64/kernel/smpboot.c:902
Boot done.
smp_boot_cpus arch/x86_64/kernel/smpboot.c:941
ENABLING IO-APIC IRQs
Synchronizing Arb IDs.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
smp_boot_cpus arch/x86_64/kernel/smpboot.c:952
Using local APIC timer interrupts.
Detected 12.516 MHz APIC timer.
smp_boot_cpus arch/x86_64/kernel/smpboot.c:963
time.c: Using PIT/TSC based timekeeping.
smp_boot_cpus arch/x86_64/kernel/smpboot.c:967
init init/main.c:675
do_pre_smp_initcalls init/main.c:621
do_pre_smp_initcalls init/main.c:627
init init/main.c:679
init init/main.c:682
Brought up 1 CPUs
init init/main.c:684
CPU0: online
domain 0: span 01
groups: 01
domain 1: span 01
groups: 01
init init/main.c:686
init init/main.c:692
do_basic_setup init/main.c:602
do_basic_setup init/main.c:604
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
IOAPIC[0]: Set PCI routing entry (1-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169
IOAPIC[0]: Set PCI routing entry (1-18 -> 0xb1 -> IRQ 18 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177
IOAPIC[0]: Set PCI routing entry (1-17 -> 0xb9 -> IRQ 17 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
Pin 1-17 already programmed
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 185
IOAPIC[0]: Set PCI routing entry (1-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 193
IOAPIC[0]: Set PCI routing entry (1-20 -> 0xc9 -> IRQ 20 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 201
Pin 1-20 already programmed
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 201
IOAPIC[0]: Set PCI routing entry (1-21 -> 0xd1 -> IRQ 21 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 209
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 209
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 209
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 209
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 209
Pin 1-16 already programmed
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B9
12 001 01 1 1 0 1 0 1 1 B1
13 001 01 1 1 0 1 0 1 1 C1
14 001 01 1 1 0 1 0 1 1 C9
15 001 01 1 1 0 1 0 1 1 D1
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ169 -> 0:16
IRQ185 -> 0:17
IRQ177 -> 0:18
IRQ193 -> 0:19
IRQ201 -> 0:20
IRQ209 -> 0:21
.................................... done.
agpgart: Detected AGP bridge 0
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 64M @ 0xf8000000
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
set_pte_phys ffffffffff600000 to 5ee000
spp_getpage 000001003fdc1000
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.15 [Flags: R/O].
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 1
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1)
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
IOAPIC[0]: Set PCI routing entry (1-6 -> 0x59 -> IRQ 6 Mode:0 Active:0)
acpi_floppy_resource: 6 ioports at 0x3f0
acpi_floppy_resource: 1 ioports at 0x3f7
floppy: controller ACPI FDC at I/O 0x3f0-0x3f5, 0x3f7-0x3f7 irq 6 dma channel 2
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
Pin 1-17 already programmed
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
sk98lin: Network Device Driver v6.23
(C)Copyright 1999-2004 Marvell(R).
Pin 1-17 already programmed
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
Pin 1-19 already programmed
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 193
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
Pin 1-19 already programmed
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 193
eth1: VIA Rhine III at 0xb000, 00:40:f4:a7:59:5e, IRQ 193.
eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.28.
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
Pin 1-20 already programmed
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 201
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD205BA, ATA DISK drive
hdb: WDC WD2500JB-00FUA0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: Hewlett-Packard CD-Writer Plus 9500, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 40088160 sectors (20525 MB) w/2048KiB Cache, CHS=39770/16/63, UDMA(66)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdb: max request size: 1024KiB
hdb: Host Protected Area detected.
current capacity is 66055244 sectors (33820 MB)
native capacity is 488397168 sectors (250059 MB)
hdb: 66055244 sectors (33820 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 p6 p7 > p3
hdc: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 209
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: irq 209, pci mem ffffff0000038000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
USB Universal Host Controller Interface driver v2.2
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 209
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 209, io base 000000000000b400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 209
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 209, io base 000000000000b800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 209
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 209, io base 000000000000c000
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Pin 1-21 already programmed
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 209
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: irq 209, io base 000000000000c400
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Intel 810 + AC97 Audio, version 1.01, 11:59:53 Oct 10 2004
Creative EMU10K1 PCI Audio Driver, version 0.20a, 00:45:48 Oct 14 2004
Pin 1-17 already programmed
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 185
emu10k1: EMU10K1 rev 5 model 0x8040 found, IO at 0xa400-0xa41f, IRQ 185
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
ALSA device list:
No soundcards found.
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09b)
powernow-k8: invalid freq entries 3300000 kHz vs. 2147483048 kHz
powernow-k8: invalid freq entries 3300000 kHz vs. 2147483048 kHz
powernow-k8: invalid freq entries 3300000 kHz vs. 2147483048 kHz
powernow-k8: invalid freq entries 3300000 kHz vs. 2147483048 kHz
powernow-k8: invalid freq entries 3300000 kHz vs. 2147483048 kHz
powernow-k8: invalid freq entries 3300000 kHz vs. 2147483048 kHz
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x2 (1500 mV)
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x6 (1400 mV)
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0xe, vid 0x0
powernow-k8: ph2 null fid transition 0xe
ACPI: (supports S0 S1 S3 S4 S5)
init init/main.c:694
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
usb 2-2: new low speed USB device using address 2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.0-2
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18,max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 188k freed
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: no IPv6 routers present
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: enabled
|
Here's my /etc/modules.d/alsa
| Code: | # Alsa 0.9.X kernel modules' configuration file.
# $Header: /var/cvsroot/gentoo-x86/media-sound/alsa-utils/files/alsa-modules.co$
# ALSA portion
# OSS/Free portion
##
## IMPORTANT:
## You need to customise this section for your specific sound card(s)
## and then run `update-modules' command.
## Read alsa-driver's INSTALL file in /usr/share/doc for more info.
##
## ALSA portion
## alias snd-card-1 snd-ens1371
## OSS/Free portion
##
# OSS/Free portion - card #1
## OSS/Free portion - card #2
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
# Set this to the correct number of cards.
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF verion 1.0.6 ---
alias char-major-116 snd
alias char-major-14 soundcore
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias snd-card-0 snd-emu10k1
alias sound-slot-0 snd-emu10k1
# --- END: Generated by ALSACONF, do not edit. --- |
Here's the results of lsmod
| Code: | Module Size Used by
snd_emu10k1 89448 0
snd_rawmidi 21860 1 snd_emu10k1
snd_ac97_codec 70468 1 snd_emu10k1
snd_util_mem 4416 1 snd_emu10k1
snd_hwdep 8456 1 snd_emu10k1 |
Here's the results of lspci
| Code: | 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South]
0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
0000:00:08.0 RAID bus controller: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) (rev 02)
0000:00:0a.0 Ethernet controller: Marvell Technology Group Ltd. Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (rev 13)
0000:00:0c.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 05)
0000:00:0c.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 05)
0000:00:0e.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 8b)
0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800South]
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
0000:01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX400] (rev a1) |
I don't think I missed anything there. And just to answer the inevitable questions ahead of time, yes, my speakers are plugged in and turned on 
Thanks ahead of time |
|
| Back to top |
|
 |
Crocodil
Apprentice
Joined: 06 May 2004
Posts: 163
Location: Poznan, Poland
|
| Posted: Thu Oct 14, 2004 9:06 am Post subject: |
|
|
Hi 
All of your modules seem to have loaded fine. I think your problem is with /etc/modules.d/alsa. Please take a closer look on the 3rd point of Gentoo Linux ALSA Guide, especially Code Listing 3.1
You should add this line to your /etc/modules.d/alsa:
| Quote: | | alias snd-card-0 snd-emu10k1 |
I see you don't have OSS emulation modules, I believe it would be wise to add them in your kernel configuration beacause there are still many programs that use OSS and not ALSA. Please remember to add the corresponding OSS lines to /ec/modules.d/alsa
I hope that helps.
Regards,
Crocodil. |
|
| Back to top |
|
|
ISN004
n00b
Joined: 07 Sep 2004
Posts: 23
|
| Posted: Thu Oct 14, 2004 9:15 am Post subject: |
|
|
Thanks for the help, but the line of code you referenced was adeed in by alsaconf. It's the third line from the bottom. Does it matter where it is in the file maybe?
As for OSS emulation, I built them into the kernel, not as modules.
Thanks for your help though. Hopefully, I can get this solved. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Multimedia
