Installed Usb Cdrom Now What

[pbrianf17]

I put my usb cdrom on now what device node is it???

please help

Brian

[cato`]

Mine is /dev/sr0
_________________
Don't mess with the Penguin.

[pbrianf17]

no luck

i tried mount /dev/sr0 -t iso9660 /mnt/cdrom1
mount: /dev/sr0 is not a valid block device

mount -t /dev/sr0 iso9660 /mnt/cdrom1
mount: fs type /dev/sr0 not supported by kernel

and i am using udev without coldplug

this may help it worked fine with redhat
dmesg

g APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3192.216 MHz processor.
Using tsc for high-res timesource
Speakup v-2.00 CVS: Wed Oct 20 14:26:13 EDT 2004 : initialized
Speakup: loading module "speakup_n"
request_module: runaway loop modprobe speakup_n
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 904176k/917504k available (3031k kernel code, 12908k reserved, 1056k data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 6307.84 BogoMIPS (lpj=3153920)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Couldn't initialize miscdevice /dev/synth.
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 09
per-CPU timeslice cutoff: 1462.76 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 6373.37 BogoMIPS (lpj=3186688)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 09
Total of 2 processors activated (12681.21 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbae7, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:02:02.2[B] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 18 (level, low) -> IRQ 18
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
Machine check exception polling timer started.
gx-suspmod: error: no MediaGX/Geode processor found!
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Starting balanced_irq
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
inotify init: minor=63
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
hw_random hardware driver 1.0.0 loaded
vesafb: ATI Technologies Inc., R350, 01.00 (OEM: ATI R350)
vesafb: VBE version: 2.0
vesafb: protected mode interface info at c000:577e
vesafb: pmi: set display start = c00c5812, set palette = c00c585e
vesafb: pmi: ports = de10 de16 de54 de38 de3c de5c de00 de04 deb0 deb2 deb4
vesafb: monitor limits: vf = 0 Hz, hf = 0 kHz, clk = 0 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x30
vesafb: framebuffer at 0xf0000000, mapped to 0xf8880000, size 16384k
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 22
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: MAXTOR 4K060H3, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
hdd: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 117266688 sectors (60040 MB) w/2000KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
libata version 1.02 loaded.
ata_piix version 1.02
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 18
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 18
ata1: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3e01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 234375000 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7b09 84:4003 85:7c69 86:3a01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 240121728 sectors:
ata2: dev 0 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: ST3120026AS Rev: 8.05
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: Maxtor 6Y120M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
st: Version 20040403, fixed bufsize 32768, s/g segs 256
SCSI device sda: 234375000 512-byte hdwr sectors (120000 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 240121728 512-byte hdwr sectors (122942 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 USB2 USB3 PCI1 KBD
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 220k freed
Adding 506036k swap on /dev/sda2. Priority:-1 extents:1
EXT3 FS on sda3, internal journal
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 803 MBytes.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[fglrx] module loaded - fglrx 3.14.1 [Sep 27 2004] on minor 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
driverloader: stack=8192/60/0 SMP
usbcore: registered new driver driverloader
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
0000:02:03.0: cache line size not set; forcing 32
eth0: New link status: Disconnected (0002)
eth0: WPA, AES, TKIP, WEP128, WEP64 supported
eth0: Wireless-B PCI Adapter at 0000:02:03.0 (MAC address 00:0C:41:87:DE:D0) ready
eth0: New link status: Connected (0001)
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i875 Chipset.
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 128M @ 0xe0000000
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 0000ff80
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 0000ff60
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 0000ff40
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 16, io base 0000ff20
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem f98c4800
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 3-2: new full speed USB device using address 2
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 17
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:02.2[B] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[fe8da000-fe8da7ff] Max Packet=[2048]
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.3.19-k2
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 18 (level, low) -> IRQ 18
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0411013600]
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x1000000
[fglrx:firegl_addmap] *ERROR* mtrr allocation failed (-22)
allocation failed: out of vmalloc space - use vmalloc=<size> to increase size.
Fire GL built-in AGP-support
Based on agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: Detected an Intel PCI to CSA bridge
agpgart: Detected Intel 875G chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Power management callback for AGP chipset installed
[fglrx] AGP detected, AgpState = 0x1f004a1b (hardware caps of chipset)
AGP: Found 2 AGPv3 devices
AGP: Doing enable for AGPv3
agpgart: Found an AGP 3.0 compliant device.
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 121909248
[fglrx] max AGP = 121909248
[fglrx] free LFB = 100659200
[fglrx] max LFB = 100659200
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 32768
Unable to identify CD-ROM format.
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x1000000
[fglrx:firegl_addmap] *ERROR* mtrr allocation failed (-22)
allocation failed: out of vmalloc space - use vmalloc=<size> to increase size.
[fglrx] free AGP = 121909248
[fglrx] max AGP = 121909248
[fglrx] free LFB = 116387840
[fglrx] max LFB = 116387840
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 32768

[pbrianf17]

i found in the usb section on the kernel support for hp CDRW0 82xx which i enabled i have an hp 8200