| View previous topic :: View next topic |
| Author |
Message |
richk449
Guru
Joined: 24 Oct 2003
Posts: 345
|
 Posted: Thu Dec 23, 2004 3:17 am Post subject: new mobo, same OS, USB prob (and a partridge in a pear tree) |
 |
|
I recently bought a new mobo, chip, and ram combo, and swapped it out, keeping the same hard drive with gentoo on it. Everything works, except for USB. I can't mount my USB flash drive, or external hard drive anymore. However, my digital camera, which transfers over USB, still works.
Getting USB to work has always seem like a bit of a black magic, so I don't really know what to do. I tried switching ohci and uhci, but it doesn't seem to make any difference. Does anyone have any ideas? |
|
| Back to top |
|
 |
richk449
Guru
Joined: 24 Oct 2003
Posts: 345
|
| Posted: Thu Dec 23, 2004 3:40 am Post subject: |
|
|
More Info:
dmesg when I plug in the stick:
| Code: | hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
uhci_hcd 0000:00:10.1: wakeup_hc
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 2-1: new full speed USB device using address 2
uhci_hcd 0000:00:10.1: uhci_result_control: failed with status 440000
[c2fbe240] link (02fbe1e2) element (0296d040)
0: [c296d040] link (0296d080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=37bc3700)
1: [c296d080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
uhci_hcd 0000:00:10.1: uhci_result_control: failed with status 440000
[c2fbe240] link (02fbe1e2) element (0296d040)
0: [c296d040] link (0296d080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=37bc3700)
1: [c296d080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
usb 2-1: device not accepting address 2, error -71
usb 2-1: new full speed USB device using address 3
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: default language 0x0409
usb 2-1: Product: USB Flash Memory
usb 2-1: SerialNumber: 09813A40D1A04DFB
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
usb-storage 2-1:1.0: usb_probe_interface
usb-storage 2-1:1.0: usb_probe_interface - got id
scsi8 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB Flash Memory Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 492544 512-byte hdwr sectors (252 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
/dev/scsi/host8/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi8, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi8, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 3
|
dmesg from mount /dev/sda1:
| Code: | Unable to load NLS charset cp437
FAT: codepage cp437 not found
Unable to load NLS charset cp437
FAT: codepage cp437 not found
|
dmesg from mount /dev/sda:
| Code: | FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
|
And the usb stick still works on my other computer running gentoo, so it is something specific to this computer and setup. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
