Tankred
n00b
Joined: 20 Aug 2003
Posts: 36
Location: NRW (Germany)
|
 Posted: Sat Mar 05, 2005 1:08 pm Post subject: nForce3 and Texas Instruments PCI1620 Controller [SOLVED] |
 |
|
There seems to be a problem with the Texas Instruments PCI1620 PC Card Controller on my laptop. I have a HP Pavilion zv5324EA and have a netgear wg511t wlan card with the atheros chipset plugged in. However it doesnt show up in lspci and is therefor not recognized. The cardbus and card are both working fine under windows.
I have found by searching the net that there were some troubles with my cardbus controller and the nforce3 chipset on a similar laptop:
http://www1.uop.edu/~khughes/presario-r3120us/
None of the tips there helped me much end my wlan card remains unrecognized. I am thankful for any advice.
Here are some informations using the gentoo-dev-sources 2.6.10-gentoo-r6:
lspci:
| Quote: | 0000:00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev a4)
0000:00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6)
0000:00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4)
0000:00:02.0 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
0000:00:02.1 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
0000:00:02.2 USB Controller: nVidia Corporation nForce3 USB 2.0 (rev a2)
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce3 Audio (rev a2)
0000:00:06.1 Modem: nVidia Corporation: Unknown device 00d9 (rev a2)
0000:00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5)
0000:00:0a.0 PCI bridge: nVidia Corporation nForce3 PCI Bridge (rev a2)
0000:00:0b.0 PCI bridge: nVidia Corporation nForce3 AGP Bridge (rev a4)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 420 Go 32M] (rev a3)
0000:02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 01)
0000:02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 01)
0000:02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading Function (rev 01)
|
dmesg:
| Quote: | Linux version 2.6.10-gentoo-r6 (root@lorien) (gcc version 3.3.5 (Gentoo Linux 3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1)) #1 Thu Mar 3 13:48:52 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
BIOS-e820: 000000001ff70000 - 000000001ff7f000 (ACPI data)
BIOS-e820: 000000001ff7f000 - 000000001ff80000 (ACPI NVS)
BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 130928
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126832 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7260
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1ff7a89f
ACPI: FADT (v001 NVIDIA CK8 0x06040000 PTL_ 0x000f4240) @ 0x1ff7ee34
ACPI: MADT (v001 NVIDIA NV_APIC_ 0x06040000 LTP 0x00000000) @ 0x1ff7eea8
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1ff7ef02
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1ff7ef2a
ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Built 1 zonelists
Kernel command line: root=/dev/hda6 acpi=noirq
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1595.792 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 512768k/523712k available (3070k kernel code, 10296k reserved, 998k data, 268k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3162.11 BogoMIPS (lpj=1581056)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff c1d3fbff 00000000 00000000
CPU: After vendor identify, caps: 078bfbff c1d3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c1d3fbff 00000000 00000010
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP Processor 3000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0e00 (from 0c00)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 788k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8bc, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 33)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Probing PCI hardware
PCI: Using IRQ router default [10de/00d0] at 0000:00:01.0
pnp: 00:00: ioport range 0x8000-0x807f could not be reserved
pnp: 00:00: ioport range 0x8080-0x80ff has been reserved
pnp: 00:00: ioport range 0x8400-0x847f has been reserved
pnp: 00:00: ioport range 0x8480-0x84ff could not be reserved
pnp: 00:00: ioport range 0x8800-0x887f has been reserved
pnp: 00:00: ioport range 0x8880-0x88ff has been reserved
pnp: 00:00: ioport range 0x2040-0x207f has been reserved
pnp: 00:00: ioport range 0x2000-0x203f has been reserved
Simple Boot Flag at 0x37 set to 0x1
Machine check exception polling timer started.
apm: BIOS not found.
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.4
inotify device minor=63
Real Time Clock Driver v1.12
vesafb: NVIDIA Corporation, NV17 Board - m17refnz, Chip Rev A5 (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:ea90
vesafb: pmi: set display start = c00ceac6, set palette = c00ceb30
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware doesn't support DCC transfers
vesafb: monitor limits: vf = 0 Hz, hf = 0 kHz, clk = 0 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
vesafb: framebuffer at 0xf8000000, mapped to 0xe0880000, using 1536k, total 32768k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (55 C)
i8042.c: Detected active multiplexing controller, rev 1.9.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
elevator: using anticipatory as default io scheduler
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HITACHI_DK23FA-60, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC DVD+/-RW ND-6450A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
st: Version 20041025, fixed bufsize 32768, s/g segs 256
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006d]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x00f8, PCI irq 10
Socket status: 30000020
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006d]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x00f8, PCI irq 11
Socket status: 30000006
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x6 (1400 mV)
powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x18 (950 mV)
cpu_init done, current fid 0x8, vid 0x6
ACPI wakeup devices:
USB0 USB1 USB2 PS2K PS2M MAC0
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... <6>kjournald starting. Commit interval 5 seconds
failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 268k freed
Adding 1052220k swap on /dev/hda7. Priority:-1 extents:1
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda6, internal journal
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xe0a84000, 00:0f:b0:3e:a4:7d, IRQ 11
eth0: Identified 8139 chip type 'RTL-8101'
nvidia: module license 'NVIDIA' taints kernel.
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:02.0: nVidia Corporation nForce3 USB 1.1
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 11, pci mem 0xe8000000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: nVidia Corporation nForce3 USB 1.1 (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 10, pci mem 0xe8001000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v2.2
usb 1-1: new low speed USB device using ohci_hcd and address 2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
input: PS/2 Generic Mouse on isa0060/serio4
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49451 usecs
intel8x0: clocking to 47473
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x3000-0x7fff: clean. |
Last edited by Tankred on Sun Mar 06, 2005 10:52 am; edited 1 time in total |
|
Kernel & Hardware
