| View previous topic :: View next topic |
| Author |
Message |
daemogorgon
n00b
Joined: 11 Mar 2005
Posts: 4
|
 Posted: Thu Mar 24, 2005 1:00 pm Post subject: [resolved] Yet another bt878 Thread (Winfast 2000 XP) |
 |
|
Hello,
I've looked at several other threads and come so far that I am quite sure I have all important modules compiled and loaded. The local settings in programs like kdetv or tvtime are set to PAL und Western Europe (Germany) for me. However, I get no channel, neither with automatic nor manual search.
The settings below in modules.autoload.d are set according to the automatic detection by the bttv module when first loaded without options.
Now I've run out of ideas where my problem could be. Here are several infos form lspci, autoloaded modules, lsmod and dmesg. It would be great if anyone here could give me some clues.
lspci output
| Code: |
0000:00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:00:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
|
/etc/modules.autoload.d/kernel-2.6
| Code: |
snd-bt87x
bttv card=34 tuner=5 radio=1
tuner
|
lsmod output (partly)
| Code: |
Module Size Used by
nvidia 4813524 12
tuner 18852 0
bttv 144972 0
video_buf 16772 1 bttv
firmware_class 7680 1 bttv
i2c_algo_bit 8584 1 bttv
v4l2_common 5120 1 bttv
btcx_risc 3976 1 bttv
i2c_core 18832 3 tuner,bttv,i2c_algo_bit
videodev 7168 1 bttv
snd_bt87x 10312 0
|
dmesg output
| Code: |
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 10 (level, low) -> IRQ 10
bttv0: Bt878 (rev 17) at 0000:00:0d.0, irq: 10, latency: 32, mmio: 0xcdcfe000
bttv0: detected: Leadtek TV 2000 XP [card=34], PCI subsystem ID is 107d:6609
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tuner: Ignoring new-style parameters in presence of obsolete ones
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "remote0"
...
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: timeout: drop=110 irq=50709/51338, risc=2aed207c, bits: HSYNC FDSR
bttv0: reset, reinitialize
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: PLL: 28636363 => 35468950 .. ok
|
Last edited by daemogorgon on Thu Mar 24, 2005 4:10 pm; edited 1 time in total |
|
| Back to top |
|
 |
daemogorgon
n00b
Joined: 11 Mar 2005
Posts: 4
|
| Posted: Thu Mar 24, 2005 4:09 pm Post subject: [resolved] Yet another bt878 Thread (Winfast 2000 XP) |
|
|
| Ok, I finally got it working. The automatic detection told me to user tuner 5, since I've read often that owners of that card were using other tuners, I just tried every Philips tuner found in the documentation, for me it was tuner 41. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Multimedia
