[clu] Apprentice
Joined: 23 Feb 2004 Posts: 160 Location: 127.0.0.1
|
Posted: Sat Mar 26, 2005 12:30 pm Post subject: scsi tape dat24 |
|
|
Привет всем
Вот возник хоботок с внутренним dat 24
Code: |
scsi: ***** BusLogic SCSI Driver Version 2.1.16 of 18 July 2002 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
scsi0: Configuring BusLogic Model BT-950 PCI Wide Ultra SCSI Host Adapter
scsi0: Firmware Version: 5.02, I/O Address: 0xC000, IRQ Channel: 20/Level
scsi0: PCI Bus: 0, Device: 5, Address: 0xFE9FA000, Host Adapter SCSI ID: 7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: Fast, Wide Negotiation: Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Driver Queue Depth: 255, Scatter/Gather Limit: 128 segments
scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0: SCSI Bus Termination: Both Enabled, SCAM: Disabled
scsi0: *** BusLogic BT-950 Initialized Successfully ***
scsi0 : BusLogic BT-950
Vendor: HP Model: C1537A Rev: L005
Type: Sequential-Access ANSI SCSI revision: 02
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec I2O RAID controller 0 at f8880000 size=100000 irq=26
dpti: If you have a lot of devices this could take a few minutes.
dpti0: Reading the hardware resource table.
TID 008 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001
TID 513 Vendor: ESG-SHV Device: SCA HSBP M15 Rev: 0.10
TID 518 Vendor: IBM Device: DDYS-T18350M Rev: S93E
TID 517 Vendor: IBM Device: DDYS-T36950M Rev: SA2A
scsi1 : Vendor: Adaptec Model: 2100S FW:370F
Vendor: IBM Model: DDYS-T18350M Rev: S93E
Type: Direct-Access ANSI SCSI revision: 03
Vendor: IBM Model: DDYS-T36950M Rev: SA2A
Type: Direct-Access ANSI SCSI revision: 03
Vendor: ESG-SHV Model: SCA HSBP M15 Rev: 0.10
Type: Processor ANSI SCSI revision: 02
sym0: <1010-66> rev 0x1 at pci 0000:00:01.0 irq 29
sym0: using 64 bit DMA addressing
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym0: SCSI BUS has been reset.
|
----
Code: |
st: Version 20041025, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi0, channel 0, id 0, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575
|
BusLogic в ядре
st и ide_tape модулями
Code: |
#mtx -f /dev/st0 status
mtx: Request Sense: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00 00 00
INQUIRY command Failed
|
есть мысли ? |
|