| View previous topic :: View next topic |
| Author |
Message |
plastikman187
Apprentice
Joined: 15 Mar 2005
Posts: 233
|
 Posted: Sat Apr 02, 2005 3:06 am Post subject: Unable to mount USB flash drive [Solved] |
 |
|
Hello,
I am trying to connect to my USB flash drive but i cannot mount it.
Here is my kernel config
| Code: |
SCSI device support --->
[*] legacy /proc/scsi/ suppor
--- SCSI support type (disk, tape, CD-ROM)
<*> SCSI disk support
<*> SCSI generic support
|
| Code: |
USB support --->
--- Miscellaneous USB options
[*] USB device filesystem
<*> EHCI HCD (USB 2.0) support
<*> UHCI HCD (most Intel and VIA) support
--- NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also
<*> USB Mass Storage support
[*] USB Mass Storage verbose debug
--- USB Input Devices
<*> USB Human Interface Device (full HID) support
[*] HID input layer support
|
| Code: |
MMC/SD Card support --->
<*> MMC support
[*] MMC debugging
<*> MMC block device driver
<M> Winbond W83L51xD SD/MMC Card Interface support
|
Here is dmesg any help would be appreciated.
| Code: |
usb 3-1: new full speed USB device using uhci_hcd and address 3
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x05e3, Product: 0x0700, Revision: 0x0113
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Vendor: Unknown, Product: USB Storage Device
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is -32, data is 85
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: *** thread sleeping.
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3usb-storage: waiting for device to settle before scanning
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x4c L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4c R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Generic Model: STORAGE DEVICE Rev: 0.01
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4d L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4d R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x8000004d L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8000004d R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4e L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4e R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x8000004e L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8000004e R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4f L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4f R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x8000004f L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8000004f R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi3, channel 0, id 0, lun 0, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
bash-2.05b$
|
Last edited by plastikman187 on Tue Apr 05, 2005 7:54 pm; edited 1 time in total |
|
| Back to top |
|
 |
plastikman187
Apprentice
Joined: 15 Mar 2005
Posts: 233
|
| Posted: Sun Apr 03, 2005 1:36 am Post subject: |
|
|
| bump |
|
| Back to top |
|
|
Baix
Tux's lil' helper
Joined: 19 Feb 2005
Posts: 77
|
| Posted: Sun Apr 03, 2005 4:17 am Post subject: |
|
|
| What error do you get when you try to mount it and what does your fstab looks like? |
|
| Back to top |
|
|
plastikman187
Apprentice
Joined: 15 Mar 2005
Posts: 233
|
| Posted: Sun Apr 03, 2005 6:34 am Post subject: |
|
|
Here is my Fstab and the error
| Code: |
# /etc/fstab: static file system information.
# $Header: /home/cvsroot/gentoo-src/rc-scripts/etc/fstab,v 1.14 2003/10/13 20:03:38 azarah Exp $
#
# noatime turns off atimes for increased performance (atimes normally aren't
# needed; notail increases performance of ReiserFS (at the expense of storage
# efficiency). It's safe to drop the noatime options if you want and to
# switch between notail and tail freely.
# <fs> <mountpoint> <type> <opts> <dump/pass>
# NOTE: If your BOOT partition is ReiserFS, add the notail option to opts.
/dev/hda3 /boot ext2 noatime 1 1
/dev/hda4 / reiserfs noatime 0 0
/dev/hda2 none swap sw 0 0
/dev/hdb2 /storage reiserfs auto,noatime 0 0
/dev/cdroms/cdrom0 /mnt/burner iso9660 noauto,user,ro 0 0
/dev/cdroms/cdrom1 /mnt/dvd iso9660 noauto,user,ro 0 0
/dev/sda1 /mnt/flash vfat defaults,user,noauto 0 0
#/dev/fd0 /mnt/floppy auto noauto 0 0
# NOTE: The next line is critical for boot!
none /proc proc defaults 0 0
# glibc 2.2 and above expects tmpfs to be mounted at /dev/shm for
# POSIX shared memory (shm_open, shm_unlink).
# (tmpfs is a dynamically expandable/shrinkable ramdisk, and will
# use almost no memory if not populated with files)
# Adding the following line to /etc/fstab should take care of this:
|
| Code: |
bash-2.05b# mount /mnt/flash/
mount: wrong fs type, bad option, bad superblock on /dev/sda1,
or too many mounted file systems
bash-2.05b#
|
|
|
| Back to top |
|
|
dsd
Developer
Joined: 30 Mar 2003
Posts: 2162
Location: nr London
|
| Posted: Sun Apr 03, 2005 9:31 am Post subject: |
|
|
file a bug. the usb-storage driver is having trouble reading the partition table - nothing you can do without jumping into the code
_________________
http://dev.gentoo.org/~dsd |
|
| Back to top |
|
|
Sysa
Apprentice
Joined: 16 Mar 2005
Posts: 161
Location: Europe
|
| Posted: Sun Apr 03, 2005 9:37 am Post subject: |
|
|
try mount /dev/sda (not /dev/sda1 !!!) and be sure that vfat is loaded ...
| plastikman187 wrote: | Here is my Fstab and the error
| Code: |
# /etc/fstab: static file system information.
# $Header: /home/cvsroot/gentoo-src/rc-scripts/etc/fstab,v 1.14 2003/10/13 20:03:38 azarah Exp $
#
# noatime turns off atimes for increased performance (atimes normally aren't
# needed; notail increases performance of ReiserFS (at the expense of storage
# efficiency). It's safe to drop the noatime options if you want and to
# switch between notail and tail freely.
# <fs> <mountpoint> <type> <opts> <dump/pass>
# NOTE: If your BOOT partition is ReiserFS, add the notail option to opts.
/dev/hda3 /boot ext2 noatime 1 1
/dev/hda4 / reiserfs noatime 0 0
/dev/hda2 none swap sw 0 0
/dev/hdb2 /storage reiserfs auto,noatime 0 0
/dev/cdroms/cdrom0 /mnt/burner iso9660 noauto,user,ro 0 0
/dev/cdroms/cdrom1 /mnt/dvd iso9660 noauto,user,ro 0 0
/dev/sda1 /mnt/flash vfat defaults,user,noauto 0 0
#/dev/fd0 /mnt/floppy auto noauto 0 0
# NOTE: The next line is critical for boot!
none /proc proc defaults 0 0
# glibc 2.2 and above expects tmpfs to be mounted at /dev/shm for
# POSIX shared memory (shm_open, shm_unlink).
# (tmpfs is a dynamically expandable/shrinkable ramdisk, and will
# use almost no memory if not populated with files)
# Adding the following line to /etc/fstab should take care of this:
|
| Code: |
bash-2.05b# mount /mnt/flash/
mount: wrong fs type, bad option, bad superblock on /dev/sda1,
or too many mounted file systems
bash-2.05b#
|
|
_________________
RedHat -> SuSE -> Debian -> Gentoo |
|
| Back to top |
|
|
plastikman187
Apprentice
Joined: 15 Mar 2005
Posts: 233
|
|
| Back to top |
|
|
plastikman187
Apprentice
Joined: 15 Mar 2005
Posts: 233
|
| Posted: Tue Apr 05, 2005 7:54 pm Post subject: |
|
|
This was a user error issue. The bug has been closed.
It seems that with this particular flash drive it has to have a card in it when it is plugged in
i noticed in the dmesg that it was being assigned to sda
| Code: |
Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi3, channel 0, id 0, lun 0, type 0
|
So if i do a
I see that the file system is located at /dev/sda1
now i can mount the USB drive
n00b error again 
Thanks for the help |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
