[X] Comment augmenter la definition de mon X ?[Resolu]

[zoltix]

Bonjour,
Maintenant tout semble bien allé sauf que je suis une triste de la définition de Xwindow 640*480 c’est pas beaucoup

J’ai regardé pour augmenter j’ai fait qlq test mais rien n’y fait. je n’arrive a monter la définition de mon X et lorsque je vais dans gnome(screen resolution) j'ai pas le choix 640*480 60Hz


Pourriez vous m’aider



Voici mon dmesg :

254MB LOWMEM available.
found SMP MP-table at 0009fe00
On node 0 totalpages: 65248
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61152 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 IBM ) @ 0x000fdfe0
ACPI: RSDT (v001 IBM CDTPWSPI 0x00001010 IBM 0x00000000) @ 0x0fee6640
ACPI: FADT (v001 IBM CDTPWSPI 0x00001010 IBM 0x00000000) @ 0x0fee65c0
ACPI: MADT (v001 IBM CDTPWSPI 0x00001010 IBM 0x00000000) @ 0x0fee6540
ACPI: DSDT (v001 IBM CDTPWSPI 0x00001000 MSFT 0x01000007) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda3
__iounmap: bad address c00fffd9
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 864.111 MHz processor.
Using tsc for high-res timesource
Speakup v-2.00 CVS: Wed Mar 2 20:22:02 EST 2005 : initialized
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254652k/260992k available (2302k kernel code, 5884k reserved, 601k data, 200k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1703.93 BogoMIPS (lpj=851968)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Couldn't initialize miscdevice /dev/synth.
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 730.77 usecs.
task migration cache decay timeout: 1 msecs.
Total of 1 processors activated (1703.93 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 01
groups: 01
domain 1: span 01
groups: 01
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd55c, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [PIN1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN3] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN4] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN6] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN7] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [PIN8] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0x800-0x87f has been reserved
pnp: 00:0b: ioport range 0xf800-0xf87f could not be reserved
pnp: 00:0b: ioport range 0xfc00-0xfc3f has been reserved
inotify device minor=63
Squashfs 2.1 (released 2004/12/10) (C) 2002-2004 Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 202M
agpgart: AGP aperture is 64M @ 0xf8000000
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
Console: switching to colour frame buffer device 80x30
I810FB: fb0 : Intel(R) 815 (Internal Graphics with AGP) Framebuffer Device v0.9.0
I810FB: Video RAM : 4096K
I810FB: Monitor : H: 29-30 KHz V: 60-60 Hz
I810FB: Mode : 640x480-8bpp@60Hz
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G chipsets
intelfb: Version 0.9.2
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Generic Mouse on isa0060/serio1
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 2
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST320413A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 39876480 sectors (20416 MB)
native capacity is 39876481 sectors (20416 MB)
hda: Host Protected Area disabled.
hda: 39876481 sectors (20416 MB) w/1024KiB Cache, CHS=39560/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
CAPI Subsystem Rev 1.1.2.8
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 7
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 200k freed
Adding 4120664k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Real Time Clock Driver v1.12
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 19, io base 0xfb00
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse Optical®] on usb-0000:00:1f.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
e100: Intel(R) PRO/100 Network Driver, 3.3.6-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 20
e100: eth0: e100_probe: addr 0xfebff000, irq 20, MAC addr 00:02:55:8C:3A:7E
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:01:0a.0: 3Com PCI 3c905B Cyclone 100baseTx at 0x7880. Vers LK1.1.19
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03c4340(lo)
IPv6 over IPv4 tunneling driver
eth1: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present


lspci


brufree01 root # lspci
0000:00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02)
0000:00:02.0 VGA compatible controller: Intel Corporation 82815 CGC [Chipset Graphics Controller] (rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 02)
0000:00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 02)
0000:00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 02)
0000:00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 02)
0000:01:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller (rev 01)
0000:01:0a.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)


brufree01 root # cat /etc/X11/xorg.conf
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
RgbPath "/usr/lib/X11/rgb"
ModulePath "/usr/lib/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/CID/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
EndSection

Section "Module"
Load "extmod"
Load "dri"
Load "dbe"
Load "record"
Load "xtrap"
Load "glx"
Load "type1"
Load "freetype"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection

Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
EndSection

Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection

Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "ColorKey" # <i>
#Option "CacheLines" # <i>
#Option "Dac6Bit" # [<bool>]
#Option "DRI" # [<bool>]
#Option "NoDDC" # [<bool>]
#Option "ShowCache" # [<bool>]
#Option "XvMCSurfaces" # <i>
#Option "PageFlip" # [<bool>]
Identifier "Card0"
Driver "i810"
VendorName "Intel Corp."
BoardName "82815 CGC [Chipset Graphics Controller]"
BusID "PCI:0:2:0"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection

[Delvin]

tu as un excellent tutorial pour la configuration de X a cette adresse : http://www.gentoo.org/doc/fr/xorg-config.xml

lis le, il y est expliqué comment changé la résolution
_________________
Ne tirez pas sur les canards !!

[zoltix]

je sais je change mais je ne voix pas la dif


Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
SubSection "Display"
Depth 1
Modes "1024x768"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768"
EndSubSection
EndSection

[kernelsensei]

vu le contenu de ton xorg.conf .. et qu'il n'y a rien de special, tu pourrais faire une detection automatique pour voir .. non ?
_________________
$ ruby -e'puts " .:@BFegiklnorst".unpack("x4ax7aaX6ax5aX15ax4aax6aaX7ax2aX5aX8 \
axaX3ax8aX4ax6aX3aX6ax3ax3aX9ax4ax2aX9axaX6ax3aX2ax4ax3aX4aXaX12ax10aaX7a").join'

[zoltix]

C'est en automaitique et ca ne change rien


Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSecti

[DidgeriDude]

Je vois que tu as le framebuffer d'activé.
Que te dis la commande :

[fb99]

met juste des modes dans ta SubSections "Display" et le tour est joué

[zoltix]

Comme j'ai décidé de tout reprendre a 0 (réinstaller)mais j'ai un autre souci de taille
[url]
https://forums.gentoo.org/viewtopic-t-323805.html[/url]