View previous topic :: View next topic |
Author |
Message |
Dawid159 Guru
Joined: 28 Jun 2004 Posts: 414 Location: /dev/Kłodzko
|
Posted: Thu Apr 21, 2005 8:28 pm Post subject: [SYSTEM/HARDWARE] NFORCE2 dziwny komunikat przy starcie |
|
|
Witam
Postanowiłem się w końcu zabrać za pewien dziwny komunikat, który dostaje podczas startu systemu Oto on:
Code: | NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
| A tutaj trochę większy wycinek z dmesg w celu pokazania kiedy pojawia się komunikat
Code: | [ 13.853779] io scheduler cfq registered
[ 13.854955] Floppy drive(s): fd0 is 1.44M
[ 13.871648] FDC 0 is a post-1991 82077
[ 13.873677] ACPI: No ACPI bus support for floppy.0
[ 13.875006] loop: loaded (max 8 devices)
[ 13.876159] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 13.877289] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 13.878514] NFORCE2: IDE controller at PCI slot 0000:00:09.0
[ 13.879695] NFORCE2: chipset revision 162
[ 13.880828] NFORCE2: not 100% native mode: will probe irqs later
[ 13.881961] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
[ 13.883098] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
[ 13.884214] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
[ 13.885332] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[ 13.886480] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[ 13.887601] Probing IDE interface ide0...
[ 14.150990] hda: WDC WD800LB-55DNA0, ATA DISK drive
[ 14.765617] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 14.766771] ACPI: No ACPI bus support for 0.0
|
Czy pozbycie się tego wpłynie jakoś na wydajność, jeżeli tak to jak się tego pozbyć
Na googlach nie udało mi się znaleźć nic sensownego |
|
Back to top |
|
|
n0rbi666 l33t
Joined: 04 Mar 2005 Posts: 707 Location: \Poland\Krakow
|
Posted: Thu Apr 21, 2005 8:33 pm Post subject: |
|
|
wg mnie cable bit - czyli bit od tego, czy kabel jest 40 czy 80 zylowy (tasma ide - ata33 czy ata100), i moze tu jest jakis blad w nf2 .... |
|
Back to top |
|
|
Mihashi Tux's lil' helper
Joined: 08 Apr 2005 Posts: 98 Location: Wroclaw, Poland
|
Posted: Thu Apr 21, 2005 8:39 pm Post subject: |
|
|
W kilku miejscach, które zapewne i Ty znalazłeś via Google, piszą iż to taki sobie bugo-warning, którym nie nalezy się przejmować, ponieważ nie wpływa na wydajność. Więc ... _________________ Mihashi |
|
Back to top |
|
|
rebus n00b
Joined: 10 Sep 2004 Posts: 61
|
Posted: Fri Apr 22, 2005 5:31 pm Post subject: |
|
|
tez mam nforce2 z tym komunikatem i z tego co pamietam to na nforce2 z ATA jest jakiś błąd sprzetowy niezgodny z ogolnym standardem i jest to komunikat tylko wskazujący że to mam miejsce i sterownik to prostuje
czyli jak kolega napisał bugo-warning |
|
Back to top |
|
|
Deadalus n00b
Joined: 25 Jul 2006 Posts: 3
|
Posted: Tue Jul 25, 2006 11:11 am Post subject: |
|
|
Witam!
Odgrzewam tego kotleta bo mam ten sam problem co Dawid159. Niby ten "bugo-warrning" nie wplywa na wydajnosc etc, ale mnie po prostu irytuje. Jak bootuje kompa to zanim sie wlaczy workarounding mija dobre 15-20 sekund Na dobra sprawe te kilkanascie sekund to prawie polowa czasu ladowania calego systemu. Jezeli nie mozna wyeliminowac tego bledu to moze da sie chociaz jakos przyspieszyc wlaczanie workaroundingu?
Dla formalnosci dmesg:
Code: |
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 6.3.9-k4
Copyright (c) 1999-2005 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.49.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IR
Q 177
PCI: Setting latency timer of device 0000:00:05.0 to 64
input: AT Translated Set 2 keyboard as /class/input/input0
eth0: forcedeth.c: subsystem: 01019:2501 bound to 0000:00:05.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
hda: HL-DT-ST DVDRAM GSA-4040B, ATAPI CD/DVD-ROM drive
hdb: ST380021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes not supported
hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 >
hda: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
|
|
|
Back to top |
|
|
Belliash Advocate
Joined: 24 Nov 2004 Posts: 2503 Location: Wroclaw, Poland
|
Posted: Tue Jul 25, 2006 11:16 am Post subject: |
|
|
Code: | NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller |
am to samo i sie tym nie prejmuje.
Nie zauwazylem tez spadku predkosci czy wydajnosci systemu. Wrecz przeciwnie. System smiga o niebo szybciej i lepiej niz Windows a przy uzyciu InitNG bootuje sie ~6sek do KDMa.
Z to niepokoi mnie to:
Code: | ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. |
Da sie cos z tym zrobic? _________________ Asio Software Technologies
Belliash IT Weblog |
|
Back to top |
|
|
quosek Apprentice
Joined: 07 Mar 2006 Posts: 269
|
Posted: Wed Jul 26, 2006 6:46 am Post subject: |
|
|
mam podobnie i nie wiem tez co z tym zrobic (kiedys szukalem tego pare h, ale nikt nie mial pomyslu....)
wiem tylko, ze to cos z przerwaniami, ale co ? |
|
Back to top |
|
|
wuja Guru
Joined: 16 Jan 2005 Posts: 323 Location: Szczecin
|
Posted: Wed Jul 26, 2006 3:45 pm Post subject: |
|
|
hmmm..... kiedyś też tak miałem z tymi przerwaniami, ale ostatnio znikło. No i niestety nie jestem pewien co mnie uszczęśliwiło, bo mniej więcej w tym samym czasie uaktualniałem BIOS, coś tam pozmieniałem w ustawieniach BIOSU (bo niechcący w czasie uaktualniania ustawiło się domyślnie/fabrycznie) no i zmieniałem kernel i być może coś w nim pozmieniałem (ACPI ) _________________ Pozdrowienia
Wojtek
www.wojciechgracz.pl |
|
Back to top |
|
|
quosek Apprentice
Joined: 07 Mar 2006 Posts: 269
|
Posted: Wed Jul 26, 2006 3:59 pm Post subject: |
|
|
ja tez bym obstawial bios, ale ..... przeciez kernel nie korzysta z biosu .....
a w jaderku - jak masz dostep do pci access Mode ? (bo mi to any lekko bruzdzi)
i to na 99% nie acpi - bo jedyne co mam z apci to glowny modul |
|
Back to top |
|
|
wuja Guru
Joined: 16 Jan 2005 Posts: 323 Location: Szczecin
|
Posted: Wed Jul 26, 2006 5:20 pm Post subject: |
|
|
quosek wrote: | ..jak masz dostep do pci access Mode ? (bo mi to any lekko bruzdzi)
.. | Zawsze miałem "any".
No nie wiem. Tak mnie kiedyś naszło na zmianę jądra z nitro na beyond-sources i przy okazji sobie przypomniałem, że b. dawno nie uaktualniałem BIOS-u _________________ Pozdrowienia
Wojtek
www.wojciechgracz.pl |
|
Back to top |
|
|
Raku Bodhisattva
Joined: 28 Feb 2004 Posts: 2374 Location: Poland
|
Posted: Wed Jul 26, 2006 5:54 pm Post subject: |
|
|
Moved from Polish to Instalacja i sprzęt. _________________ raku
Powered by Archlinux |
|
Back to top |
|
|
quosek Apprentice
Joined: 07 Mar 2006 Posts: 269
|
Posted: Wed Jul 26, 2006 7:26 pm Post subject: |
|
|
to moze to faktycznie cos z biose
ale mi sie zawsze wydawalo, ze bios nie ma nic do kernala i Linuxa - i pare razy np. uzywalem stacji dyskietek wylaczonej w biose.....
chociaz jezeli to przerwania to moze to jest na troche nizszym poziomie - mozesz dac skrotowy spic ustawien w biosie zwiazanych z irq ? |
|
Back to top |
|
|
wuja Guru
Joined: 16 Jan 2005 Posts: 323 Location: Szczecin
|
Posted: Wed Jul 26, 2006 9:39 pm Post subject: [ot] |
|
|
Code: | Power Managment Setup - IRQ Event Activity Detect -> IRQs Activity Monitoring ->
IRQs Activity - Primary
IRQ 3-7 i 9-14 - Enabled
IRQ 8 i 15 - Disabled |
Code: | PnP/PCI Configuration -> Resources Controlled by Auto(ESCD)
PCI Slot - Auto |
_________________ Pozdrowienia
Wojtek
www.wojciechgracz.pl |
|
Back to top |
|
|
pancurski Guru
Joined: 15 Sep 2005 Posts: 495 Location: Lublin, Poland / Slough, UK
|
Posted: Thu Jul 27, 2006 12:30 pm Post subject: |
|
|
mam ten sam chipset ale żaden komunikat mi nie wyskakuje, jaka to plyta glowna? w moim przypadku to Epox 8RDA+ |
|
Back to top |
|
|
|