View previous topic :: View next topic |
Author |
Message |
totencham Apprentice
Joined: 05 Dec 2004 Posts: 299 Location: Szczecin, Poland
|
Posted: Fri May 20, 2005 9:44 pm Post subject: [solved][eagle-usb] failed to launch connection |
|
|
Eagle-usb używam odkąd mam gentoo na dysku (a nawet od wcześniej) i nie sprawiało większych problemów. Teraz jednak, nagle, po wydaniu komendy "startadsl' otrzymuję komunikat "Failed to launch connection". Gdy daję "eaglectrl -w", to dowiaduję się, że "device or resource busy", niezależnie kiedy to wpiszę. Eaglestat mówi, że "modem is operational" . Nie mam pojęcia o co chodzi, jak wspomniałem problem pojawił się nagle. Próbowałem rozwiązać problem emergując różne wersje eagle-usb (których na szczęście nie wywalam z distfiles), edytując pliki konfiguracyjne i podłączając/odłączając modem. Nic z tego.
Jedyną rzeczą emergowaną od czasu ostatniego działania eagle-usb jest u mnie nowy portage, wraz z bzip2 i binutils.
Czy ktoś mógłby mi pomóc? _________________ http://gentoo-wiki.com/HOWTO_Index
cd /usr/src/linux && egrep -ir "( fuck)|( shit)" *
Linux registered user #376896
Last edited by totencham on Wed May 25, 2005 2:26 pm; edited 1 time in total |
|
Back to top |
|
|
milu Bodhisattva
Joined: 03 May 2004 Posts: 1122 Location: Poland, Konstancin-Jeziorna
|
Posted: Fri May 20, 2005 10:23 pm Post subject: |
|
|
Spróbuj podmiankę binutils na starsze?
Nie zaktualizowałeś może jeszcze baselayout'a? z jedną wersją był problem który następnego dnia został poprawiony(u mnie się Xy nie odpalały na nim). _________________ Pozdrawiam,
Milu
------------------------------------
Registered Linux User: #246079
Zanim zadasz pytanie przeczytaj to dokładnie!! |
|
Back to top |
|
|
totencham Apprentice
Joined: 05 Dec 2004 Posts: 299 Location: Szczecin, Poland
|
Posted: Sun May 22, 2005 11:25 am Post subject: |
|
|
Niestety, emerge starego binutils nie pomaga. Baselayouta mam najnowszego (1.11.12-r1). _________________ http://gentoo-wiki.com/HOWTO_Index
cd /usr/src/linux && egrep -ir "( fuck)|( shit)" *
Linux registered user #376896 |
|
Back to top |
|
|
totencham Apprentice
Joined: 05 Dec 2004 Posts: 299 Location: Szczecin, Poland
|
Posted: Mon May 23, 2005 10:18 am Post subject: |
|
|
Dołączam jeszcze trochę info, zebrane przez eagle-usb:
Code: |
Diagnostic (1.21 2005/01/16) driver eagle-usb 20050522224540
# System Information
Linux kalarepa 2.6.11-gentoo-r5 #2 SMP Mon Apr 4 08:19:15 CEST 2005 i686 Pentium III (Coppermine) GenuineIntel GNU/Linux
Gentoo Base System version 1.6.12
Linux version 2.6.11-gentoo-r5 (root@Kalarepa) (gcc version 3.3.5 (Gentoo Linux 3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1)) #2 SMP Mon Apr 4 08:19:15 CEST 2005
gcc version 3.3.5 (Gentoo Linux 3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1) used : 3.3.5 (Gentoo Linux 3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1)
# Dependances
Verify dependances on source by hand (kernel-source...)
lrwxrwxrwx 1 root root 22 kwi 3 11:15 linux -> linux-2.6.11-gentoo-r5
drwxr-xr-x 3 root root 4096 maj 3 12:21 linux-2.6.11-ck4
drwxr-xr-x 20 root root 4096 maj 2 16:00 linux-2.6.11-gentoo-r5
drwxr-xr-x 18 root root 4096 kwi 8 12:54 linux-2.6.11-gentoo-r6
drwxr-xr-x 18 root root 4096 maj 2 16:00 linux-2.6.11-gentoo-r7
drwxr-xr-x 18 root root 4096 maj 10 18:53 linux-2.6.11-gentoo-r8
Warning : available gcc and the version used to compile the kernel differ
Advice : that's a standard problem on debian, revert to gcc version used for kernel
# Kernel config : usb modules
eagle_usb 126560 0
# pci & usb configuration (check for latency, only keep relevant lines about USB)
0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
0000:00:07.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0648 (rev 01)
0000:00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
0000:00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 08)
0000:01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 04)
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 3).
Master Capable. Latency=64.
Prefetchable 32 bit memory at 0xe4000000 [0xe7ffffff].
Bus 0, device 1, function 0:
PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 3).
Master Capable. Latency=64. Min Gnt=136.
Bus 0, device 4, function 0:
ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 2).
Bus 0, device 4, function 1:
IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 1).
Master Capable. Latency=32.
I/O at 0xd800 [0xd80f].
Bus 0, device 4, function 2:
USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 1).
IRQ 5.
Master Capable. Latency=32.
I/O at 0xd400 [0xd41f].
Bus 0, device 4, function 3:
Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 2).
IRQ 9.
Bus 0, device 7, function 0:
RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0648 (rev 1).
IRQ 10.
Master Capable. Latency=32. Min Gnt=2.Max Lat=4.
I/O at 0xd000 [0xd007].
I/O at 0xb800 [0xb803].
I/O at 0xb400 [0xb407].
I/O at 0xb000 [0xb003].
I/O at 0xa800 [0xa80f].
Bus 0, device 13, function 0:
Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 8).
IRQ 5.
Master Capable. Latency=32. Min Gnt=2.Max Lat=20.
I/O at 0xa400 [0xa41f].
Bus 0, device 13, function 1:
Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 8).
Master Capable. Latency=32.
I/O at 0xa000 [0xa007].
Bus 1, device 0, function 0:
VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 4).
IRQ 11.
Master Capable. Latency=64. Min Gnt=16.Max Lat=32.
Prefetchable 32 bit memory at 0xe2000000 [0xe3ffffff].
Non-prefetchable 32 bit memory at 0xe1000000 [0xe1003fff].
Non-prefetchable 32 bit memory at 0xe0800000 [0xe0ffffff].
Bus 001 Device 004: ID 1110:9021 Analog Devices Canada, Ltd (Allied Telesyn)
Bus 001 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
Bus 001 Device 001: ID 0000:0000
# interruptions' affectation
CPU0
0: 1241394 XT-PIC timer
1: 919 XT-PIC i8042
2: 0 XT-PIC cascade
5: 170150 XT-PIC uhci_hcd, EMU10K1
9: 0 XT-PIC acpi
11: 100829 XT-PIC mga@pci:0000:01:00.0
12: 12215 XT-PIC i8042
14: 8201 XT-PIC ide0
15: 22231 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
# disk uses dma ? [ OK ]
# module loaded ? [ OK ]
# modem operational ? [ OK ]
eagle-usb status display
-------------------------------------------------------------
Driver version 2 Chipset: Eagle2
Vendor ID : 0x1110 Product ID : 0x9021 Rev: 0x500b
USB Bus : 001 USB Device : 004 Dbg mask: 0x4
Ethernet Interface : eth0
MAC: 00:60:4c:3c:65:fc
Tx Rate 96 Rx Rate 160
FEC 0 Margin 31 Atten 0 dB
VID-CPE 0 VID-CO 28 HEC 0
VPI 0 VCI 35 Delin GOOD
Cells Tx 479 Cells Rx 356
Pkts Tx 325 Pkts Rx 330
OAM 0 Bad VPI 0 Bad CRC 0
Oversiz. 0
Modem is operational
# Config vpi/vci/encapsulation/isp : 23 6 (pppoa) PL01
# pppd launched ? [ KO ]
# /etc/resolv.conf should contain the DNS
nameserver 194.204.152.34
nameserver 217.98.63.164
domain kalarepa
eth0 Link encap:Ethernet HWaddr 00:60:4C:3C:65:FC
UP BROADCAST RUNNING MULTICAST MTU:65535 Metric:1
RX packets:330 errors:0 dropped:0 overruns:0 frame:0
TX packets:325 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5274 (5.1 Kb) TX bytes:16037 (15.6 Kb)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:200 (200.0 b) TX bytes:200 (200.0 b)
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo
# ping IP ? [ KO ]
# test DNS resolution ? [ KO ]
##Complete diagnostic has been saved on /var/log/eagle-usb/eagle_diag_20050522224540.txt
##Please keep only relevant data and remove personal informations.
|
_________________ http://gentoo-wiki.com/HOWTO_Index
cd /usr/src/linux && egrep -ir "( fuck)|( shit)" *
Linux registered user #376896 |
|
Back to top |
|
|
^marcs Apprentice
Joined: 09 Mar 2005 Posts: 169
|
Posted: Mon May 23, 2005 9:20 pm Post subject: |
|
|
ja ten problem obserwuje u siebie od dłuższego czasu, jak odpalam inet
startadsl ; stopadsl;startadsl i za drugim razem startadsl juz dziala normalnie.
troche dlugo trwa zanim 1 startadsl wywali ten błąd, wiec robie też startadsl na konsoli A, przełączam sie na k. B daje stopadsl(czekam az się stopadsl skonczy) i startadsl znowu i wtedy dziala
wniosek, dziala tylko po stopadsl (ale zaraz po wlaczeniu systemu jak dasz stopadsl;startadsl to nie zadziala tez)
nie wiem o co chodzi - nie wspomne juz o skrypcie startowym eagle-usb - który jeszcze nigdy mi nie zadziałał :/
czemu userzy neostrady musza być poszkodowani na kazdym kroku?
m. |
|
Back to top |
|
|
totencham Apprentice
Joined: 05 Dec 2004 Posts: 299 Location: Szczecin, Poland
|
Posted: Mon May 23, 2005 11:21 pm Post subject: |
|
|
Dzięki, jutro spróbuję!
Ja dotychczas neo odpalałem w taki sposób:
Code: |
eagleconfig && startads && ping wp.pll && startadsl && startadsl
|
gdyż po pierwszym startadsl po minucie modem sam się rozłączał i trzeba było jeszcze 2 razy jeszcze tą komendę zapuścić Takie odpalanie "na patencie".
Swoją drogą dziwna sprawa, takie rzeczy nie powinny dziać się od tak sobie :/ Takie eagle-usb w wersji chyba 2.3.1 wogóle mi nie działa, musiałem korzystać z 2.2.1. _________________ http://gentoo-wiki.com/HOWTO_Index
cd /usr/src/linux && egrep -ir "( fuck)|( shit)" *
Linux registered user #376896 |
|
Back to top |
|
|
flakusiek Tux's lil' helper
Joined: 12 Mar 2005 Posts: 83 Location: Gdansk[PL]
|
Posted: Tue May 24, 2005 9:40 am Post subject: |
|
|
ehh ja mialem problemy ze wszystkimi wersjami :/
jedyna ktora mi dobrze działała(i nadal działa) to 1.9.8 !! _________________ HP Compaq nc6000
Linux Registered User : #385414 |
|
Back to top |
|
|
totencham Apprentice
Joined: 05 Dec 2004 Posts: 299 Location: Szczecin, Poland
|
Posted: Tue May 24, 2005 10:07 am Post subject: |
|
|
Co tu dużo mówić, metoda "startadsl ; stopadsl ; startadsl" u mnie nie działa ;(.
Pobawię się jeszcze starszymi wersjami, może pomoże. _________________ http://gentoo-wiki.com/HOWTO_Index
cd /usr/src/linux && egrep -ir "( fuck)|( shit)" *
Linux registered user #376896 |
|
Back to top |
|
|
Robert W. Guru
Joined: 13 Jul 2004 Posts: 365 Location: Kobyłka
|
Posted: Tue May 24, 2005 3:27 pm Post subject: |
|
|
A ja mam tak:
Neostrada startuje mi dzięki 'startadsl' które mam wpisane do local.start, ale mam 100 % obciążenia procesora, robię ręcznie 'stopadsl', obciążenie spada i wtedy 'startadsl'. Niedogodności te powstały po moim przjśćiu na ~x86. |
|
Back to top |
|
|
totencham Apprentice
Joined: 05 Dec 2004 Posts: 299 Location: Szczecin, Poland
|
Posted: Wed May 25, 2005 2:25 pm Post subject: |
|
|
Eh, ale gafa . Problem rozwiązany - jego przyczyną było podanie błędnego loginu do neostrady :/ _________________ http://gentoo-wiki.com/HOWTO_Index
cd /usr/src/linux && egrep -ir "( fuck)|( shit)" *
Linux registered user #376896 |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|