| View previous topic :: View next topic |
| Author |
Message |
mogosjoh
Tux's lil' helper
Joined: 24 Apr 2002
Posts: 79
Location: Plymouth, MI
|
 Posted: Mon Feb 10, 2003 7:06 am Post subject: soulseek problems (wxPython) |
 |
|
hey all,
So I haven't run soulseek in quite some time, and I went to run it today and was greeted with:
You're using an old version of wxPython libraries (2.4.0)
You should install wxPython 2.3.3 or newer
Now, I have wxPython 2.4.0.2 installed. So I unmerged soulseek, then wxPython, then remerged soulseek (and therefore wxpython) and it still gives the same error. What gives??
-John |
|
| Back to top |
|
 |
mogosjoh
Tux's lil' helper
Joined: 24 Apr 2002
Posts: 79
Location: Plymouth, MI
|
| Posted: Mon Feb 10, 2003 7:09 am Post subject: |
|
|
| update: temporarily fixed by commenting out wxPython checking area. Anybody know the real solution?? I'm looking into it. |
|
| Back to top |
|
|
mogosjoh
Tux's lil' helper
Joined: 24 Apr 2002
Posts: 79
Location: Plymouth, MI
|
| Posted: Mon Feb 10, 2003 7:14 am Post subject: |
|
|
oh man, this is pretty sweet. Soulseek got shut down (temporarily, I hope) Friday. What luck I have. Details as follows:
http://www.remmelt.com/slskboard/
man, what luck. Hopefully soulseek will be back up again in full capacity. Does anybody know of any other soul seek servers around?
-john |
|
| Back to top |
|
|
Raoul_Duke
l33t
Joined: 15 Dec 2002
Posts: 694
Location: Caerdydd, Wales
|
| Posted: Mon Feb 10, 2003 8:55 am Post subject: |
|
|
I think there's only one soulseek server........hang tight, it's been offline longer than this before  |
|
| Back to top |
|
|
max_colby
Tux's lil' helper
Joined: 30 Nov 2002
Posts: 149
Location: Ottawa, Canada
|
| Posted: Sat Feb 15, 2003 12:25 am Post subject: |
|
|
| Soulseek is back up! Unfortunately, I can't connect using pysoulseek, but my roomates running Windows are having no problem getting on. Are other Linux users having problems connecting? |
|
| Back to top |
|
|
Thunnus
n00b
Joined: 15 Feb 2003
Posts: 18
Location: Brazil
|
| Posted: Sat Feb 15, 2003 4:42 pm Post subject: |
|
|
Finally I installed PySoulSeek. The server is up and I'm downloading right now max_colby.
To install PySoulSeek I needed to:
- Take out gtk2 from make.conf
- Unmerge gtk+, wxGTK, wxPython, Pysoulseek, due my previous tries.
- And finally, into the X (I use fluxbox)
emerge -u /usr/portage/net-p2p/pysoulseek/pysoulseek-0.4.10d.ebuild
if run out of X it fail! 
Have fun! |
|
| Back to top |
|
|
max_colby
Tux's lil' helper
Joined: 30 Nov 2002
Posts: 149
Location: Ottawa, Canada
|
| Posted: Sat Feb 15, 2003 9:17 pm Post subject: |
|
|
| pysoulseek compiles and runs, but the options to Connect and Disconnect from the server are greyed out. If I check "debug messages" I actually get messages, but I can't properly connect to the server |
|
| Back to top |
|
|
Thunnus
n00b
Joined: 15 Feb 2003
Posts: 18
Location: Brazil
|
| Posted: Thu Feb 27, 2003 1:09 pm Post subject: |
|
|
I had the same problem. I tried change versions, different usernames and recompile dependences alone.
I don't know until now what happened, but after I did as described before everything runs OK. |
|
| Back to top |
|
|
|
Other Things Gentoo
