| View previous topic :: View next topic |
| Author |
Message |
FRLinux
n00b
Joined: 09 May 2002
Posts: 39
Location: Dublin
|
 Posted: Mon Aug 01, 2005 12:57 pm Post subject: NForce4 & USB 2.0 issue |
 |
|
Hello,
I have an Asus A8N-SLI Deluxe motherboard with a 3000+ AMD64 Venice (Stepping E3). I have installed and recompiled a brand new Gentoo on this with all AMD64 flags (this is a 2.6.12-gentoo-r6 kernel) and for some reason, USB 2.0 support is utterly broken. I seem to be able to get only USB 1.1 speeds. I upgraded the BIOS to 1008 (1011 has been bad karma for me ...) but still get this on USB device connection :
| Code: |
hub 1-0:1.0: state 5 ports 10 chg 0000 evt 0010
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS
hub 1-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 5 ports 10 chg 0000 evt 0010
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 4, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS
usb 1-4: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS
usb 1-4: default language 0x0409
usb 1-4: new device strings: Mfr=1, Product=3, SerialNumber=2
usb 1-4: Product: OneTouch
usb 1-4: Manufacturer: Maxtor
usb 1-4: SerialNumber: A81SS2KE
usb 1-4: hotplug
usb 1-4: adding 1-4:1.0 (config #1, interface 0)
usb 1-4:1.0: hotplug
hub 1-0:1.0: state 5 ports 10 chg 0000 evt 0010
Initializing USB Mass Storage driver...
usb-storage 1-4:1.0: usb_probe_interface
usb-storage 1-4:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x0d49, Product: 0x7000, Revision: 0x0200
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is -32, data is 0
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=88 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: *** thread sleeping.
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
|
And this is where it gets annoyed :
| Code: |
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Maxtor Model: OneTouch Rev: 0201
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sdb: 585938944 512-byte hdwr sectors (300001 MB)
sdb: assuming drive cache: write through
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x5 L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sdb: 585938944 512-byte hdwr sectors (300001 MB)
sdb: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x6 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
p1 p2 p3
Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
|
From then, i can copy stuff but dead slow ... The modules i am using are ohci_hcd, ehci_hcd
Any help welcome ...
Steph
_________________
-
"Step by step, the penguins are taking my sanity apart ..." |
|
| Back to top |
|
 |
fangorn
Veteran
Joined: 31 Jul 2004
Posts: 1886
|
| Posted: Mon Aug 01, 2005 2:49 pm Post subject: |
|
|
Do you handle youre USB by loading the modules or does hotplug and/or udev handle the module loading?
If you load the modules by hand (or with /etc/modules.autoload.d/) you could try loading the ehci_hcd module first and if that fails, load the ohci_hcd and then compare the error messages. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
