hibernate error (suspend2)

[MethodGuy]

I followed the instructions in this wiki to get hibernate to work

http://gentoo-wiki.com/HOWTO_Software_Suspend_v2

when I tested it I got this

# dmesg
Software Suspend 2.2-rc6: Initiating a software suspend cycle.
suspend_userui: userui_program not configured. suspend_userui disabled.
Software Suspend 2.2-rc6: Swapwriter: Signature found.
Software Suspend 2.2-rc6: Suspending enabled.
Freezing processes
Preparing Image.
Starting to save the image..
Writing caches...
20%...40%...60%...80%...100%...done.
Doing atomic copy.
ACPI: PCI interrupt for device 0000:02:08.0 disabled
ACPI: PCI interrupt for device 0000:02:05.1 disabled
ACPI: PCI interrupt for device 0000:02:05.0 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.0 to 64
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.1 to 64
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.2 to 64
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:02:05.0[A] -> Link [LNKF] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:02:05.1[B] -> Link [LNKG] -> GSI 9 (level, low) -> IRQ 9
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Writing kernel & process data...
20%...40%...<6>Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2548b1, caps: 0x8047 53/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
60%...80%...100%...done.
Seeking to enter ACPI state
ACPI: PCI interrupt for device 0000:02:08.0 disabled
ACPI: PCI interrupt for device 0000:02:05.1 disabled
ACPI: PCI interrupt for device 0000:02:05.0 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
Failed to enter state.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.0 to 64
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.1 to 64
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.2 to 64
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:02:05.0[A] -> Link [LNKF] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt 0000:02:05.1[B] -> Link [LNKG] -> GSI 9 (level, low) -> IRQ 9
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Reading caches...
20%...40%...60%...80%...100%...done.
Software Suspend 2.2-rc6: Suspend failed, trying to recover...
Please include the following information in bug reports:
- SUSPEND core : 2.2-rc6
- Kernel Version : 2.6.13-suspend2-r4
- Compiler vers. : 3.4
- Attempt number : 1
- Pageset sizes : 10861 (10861 low) and 44079 (44079 low).
- Parameters : 0 32 0 1 0 5
- Calculations : Image size: 55145. Ram to suspend: 2263.
- Limits : 130944 pages RAM. Initial boot: 125315.
- Overall expected compression percentage: 0.
- Compressor lzf enabled.
Compressed 225034240 bytes into 121153550 (46 percent compression).
- Swapwriter active.
Swap available for image: 218883 pages.
- Preemptive kernel.
- SMP kernel.
- Max extents used: 4
- I/O speed: Write 35 MB/s, Read 26 MB/s.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode

thanks

[vladgrigorescu]

Umm... I think we're going to need a bit more information. What kind of computer is it? What kernel is it running? What is the output of emerge --info?

[Archangel1]

It says it failed to enter the ACPI state - from /etc/hibernate/hibernate.conf, what state is it entering? Don't use 3 - 4 generally works, but you can do a full poweroff instead with suspend2 if ACPI is causing problems.
_________________
What are you, stupid?