View previous topic :: View next topic |
Author |
Message |
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Thu Dec 29, 2005 9:50 pm Post subject: Edimax WLAN Stick mit zd1211 [solved] |
|
|
Ich habe es endlich geschafft, den besagten Stick zu installieren. Das modul wird ohne Probleme geladen. Wenn ich danach aber entweder mit
oder
Code: |
ln -s /etc/init.d/net.lo /etc/init.d/net.wlan0
/etc/init.d/net.wlan0 start
|
versuche, den Stick zu starten, hängt sich der Rechner augenblicklich auf.
Last edited by Ampheus on Sat Jan 14, 2006 6:33 pm; edited 1 time in total |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Sat Dec 31, 2005 12:02 am Post subject: |
|
|
So mit dem Kernel 2.6.14-r5 komme ich etwas weiter:
Code: |
/etc/init.d/net.wlan0 start
*Caching service depencies...
*Service 'cupsd' should be AFTER service 'vmware', but one of the services 'vmware' depends on 'cupsd'!
*Starting service net.wlan0
|
Danach hängt er sich direkt wieder auf. Die Warnung wundert mit, da weder 'cupsd' noch 'vmware' in einem meiner runlevel sind.
Hier einfach mal meine /etc/conf.d/net
Code: |
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /etc/conf.d/net.example and save your configuration
# in /etc/conf.d/net (this file :]!).
modules=( "ifconfig" )
config_wlan0=( "dhcp" )
|
Und hier meine /etc/conf.d/wireless
Code: |
essid_wlan0="WLAN"
mode_wlan0="Managed"
key_WLAN="s:70616C6F6D696E6F70616C6F6D enc open"
preferred_aps=( "WLAN" )
|
Ich hoffe, da kann jemand etwas mit anfangen. |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Sat Dec 31, 2005 12:15 am Post subject: |
|
|
ifconfig zeigt mir folgendes:
Code: |
eth0 Link encap:Ethernet HWaddr 00:11:2F:B8:74:58
inet addr:192.168.178.24 Bcast:192.168.178.255 Mask:255.255.255.0
inet6 addr: fe80::211:2fff:feb8:7458/64 Scope:Link
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1697 errors:0 dropped:0 overruns:0 frame:0
TX packets:1793 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1053248 (1.0 Mb) TX bytes:449442 (438.9 Kb)
Interrupt:193 Memory:fdd00000-0
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:800 (800.0 b) TX bytes:800 (800.0 b)
|
iwconfig:
Code: |
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
wlan0 no wireless extensions.
|
Vielleicht liegt ja hier das Problem? |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Sat Dec 31, 2005 12:42 am Post subject: |
|
|
Ich habe gerade in diesem HowTo http://de.gentoo-wiki.com/Rt2500_auf_AMD64 gelesen, dass es daran liegen könnte, dass SMP im Kernel ist, also habe ich gerade meinen Kernel neu kompiliert. Als ich dann make modules_install gemacht habe, bekomme ich die Meldung
Code: |
if [ -r System.map -a -x /sbin/depmod ]; then /sbin/depmod -ae -F System.map 2.6.14-gentoo-r5; fi
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _read_unlock
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _write_lock_irq
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _spin_unlock
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _spin_unlock_irqrestore
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol del_timer_sync
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _spin_lock_irqsave
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _spin_lock
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _write_unlock_irq
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _read_lock
WARNING: /lib/modules/2.6.14-gentoo-r5/net/zd1211_mod.ko needs unknown symbol _spin_trylock
|
Das kommt nur, wenn ich den Kernel ohne SMP kompiliere. |
|
Back to top |
|
|
firefly Watchman
Joined: 31 Oct 2002 Posts: 5207
|
Posted: Sat Dec 31, 2005 1:51 am Post subject: |
|
|
ein re-emergen des zd1211 paketes sollte genügen _________________ Ein Ring, sie zu knechten, sie alle zu finden,
Ins Dunkel zu treiben und ewig zu binden
Im Lande Mordor, wo die Schatten drohn. |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Sat Dec 31, 2005 1:29 pm Post subject: |
|
|
Jap. Für die letzten Meldungen trad das zu. Leider bleibt der PC immernoch hängen, wenn ich wlan0 starten will. |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Tue Jan 03, 2006 5:06 am Post subject: |
|
|
habe das problem gefunden...es geht darum, dass der treiber keinen 64 bit support hat. da mein system allerdings x86_64 ist, habe ich es mit dem ndiswrapper ausprobiert. dies funktioniert leider auch nicht. hier meine dmesg:
Code: |
ndiswrapper (free_all_objects:330): object ffff81000e731228 type 2 was not freed, freeing it now
ndiswrapper version 1.7 loaded (preempt=no,smp=no)
ndiswrapper (check_nt_hdr:149): Windows driver is not 64-bit; bad magic: 010B
ndiswrapper (load_sys_files:218): couldn't prepare driver 'zd1211u'
ndiswrapper (load_wrap_driver:112): loadndiswrapper failed (65280); check system log for messages from 'loadndisdriver'
ndiswrapper: probe of 1-5:1.0 failed with error -22
usbcore: registered new driver ndiswrapper
|
gibt es irgendwo einen treiber für winxp 64bit? ich hab schon danach gegooglet aber leider nichts gefunden. |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Wed Jan 04, 2006 1:03 am Post subject: |
|
|
naja, da dies sowieso in einen monolog auszuarten scheint, schreib ich euch mal meinen weiteren problemverlauf.
auf der sourceforce seite des treibers fand ich einen 64bit patch. hab die datei angepasst und wollte kompilieren. leider wieder mit mehreren fehlermeldungen. also habe ich einen test gemacht und den treiber neu entpackt und versucht zu kompilieren, klappt auch nicht. nächste idee: /usr/portage/distfiles nachgeshen, den treiber rauskopiert und entpackt. versucht zu kompilieren, klappt nicht. seltsamerweise lässt sich dasselbe packet aber mit portage kompilieren. beim normalen kompilieren bekomme ich diese fehlermeldung:
Code: |
make
make V=0 -C /usr/src/linux SUBDIRS=/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5 modules
make[1]: Entering directory `/usr/src/linux-2.6.14-gentoo-r5'
CC [M] /home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.o
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_USB_WRITE_EEPROM_DATA':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:316: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:316: error: (Each undeclared identifier is reported only once
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:316: error: for each function it appears in.)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_USB_ProgramFlash':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:365: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_USB_PACKAGE_READ_REGISTER':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:429: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_USB_PACKAGE_WRITE_REGISTER':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:572: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1126:5: warning: "fVERIFY_FLASH" is not defined
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_USB_SET_RF_REG':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1243: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_tx_timeout':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1314: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_InitSetup':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1371: warning: cast to pointer from integer of different size
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1387: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_intr_cb':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1825: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_submit_rx_urb':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:1919: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c: In function `zd1211_submit_tx_urb':
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:2006: warning: cast to pointer from integer of different size
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:2006: warning: cast to pointer from integer of different size
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:2012: warning: cast to pointer from integer of different size
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:2012: warning: cast to pointer from integer of different size
/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.c:2027: error: `URB_ASYNC_UNLINK' undeclared (first use in this function)
make[2]: *** [/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5/zd1211.o] Error 1
make[1]: *** [_module_/home/amp/zd1211/zd1211/src/modules-2.6.14-gentoo-r5] Error 2
make[1]: Leaving directory `/usr/src/linux-2.6.14-gentoo-r5'
make: *** [all] Error 2
|
|
|
Back to top |
|
|
genstef Retired Dev
Joined: 13 Jun 2004 Posts: 668 Location: M/Bay/Germany
|
Posted: Wed Jan 04, 2006 2:24 am Post subject: |
|
|
Der Treiber im svn soll auf amd64 laufen hab ich gehört ..
http://zd1211.ath.cx/ |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Wed Jan 04, 2006 3:56 am Post subject: |
|
|
der treiber kompiliert problemlos, bringt allerdings hinterher nach einem modprobe zd1211
Code: |
zd1211 - http://zd1211.ath.cx/
Based on www.zydas.com.tw driver version 2.0.0.0
Release Ver = 4802
EEPORM Ver = 4330
zd1211: usb_control_msg 1 fail: FFFFFF92
zd1211_Download_IncludeFile failed
zd1211: probe of 1-5:1.0 failed with error -5
usbcore: registered new driver zd1211
|
in der dmesg.
dementsprechend klaptt auch ein ifconfig wlan0 up nicht, welches mir
Code: |
wlan0: unknown interface: No such device
|
ausgibt. |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Tue Jan 10, 2006 2:06 am Post subject: |
|
|
So. Mal ein update:
Neue Revision(r51), neues Glück....
Compilen und installieren klappt mit kleinen Änderungen am Makefile.
nach dem modprobe:
dmesg:
Code: |
ZD1211B - http://zd1211.ath.cx/
Based on www.zydas.com.tw driver version 2.0.0.0
usbcore: registered new driver zd1211b
|
iwconfig:
Code: |
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
|
ifconfig wlan0 up:
Code: |
wlan0: unknown interface: No such device
|
Jetzt bin ich völlig verwirrt. dmesg zeigt keinerlei fehler an, lsmod zeigt auch, dass der Treiber geladen ist. Das Gerät wird aber immernoch nicht verfügbar. |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Tue Jan 10, 2006 3:12 am Post subject: |
|
|
So nochmal update:
Alte Module komplett gelöscht und nur das neue installiert.
iwconfig:
Code: |
gentoo / # iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
Warning: Driver for device wlan0 has been compiled with version 19
of Wireless Extension, while this program supports up to version 17.
Some things may be broken...
wlan0 802.11b/g NIC ESSID:""
Mode:Managed Frequency=2.462 GHz Access Point: 00:00:00:00:00:00
Bit Rate:1 Mb/s
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=20/92 Signal level=27/154 Noise level=161/154
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:260 Invalid misc:0 Missed beacon:0
|
ifconfig wlan0:
Code: |
wlan0 Link encap:Ethernet HWaddr 00:0E:2E:50:CF:0C
inet6 addr: fe80::20e:2eff:fe50:cf0c/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
|
Ich bin jetzt sehr nahe dran. Es geht jetzt wahrscheinlich nur noch um Konfiguration. Meine configs stehe ja weiter oben. Wäre echt nett, wenn daraus jemand schlau werden könnte. Ich benutze einen 128bit WEP key, essid ist WLAN und ip vom router 192.168.178.1 Wenn mir jetzt jemand sagen könnte, wie ich meine config Dateien um schreiben soll..
Die HowTos auf gentoo-wiki etc. habe ich schon ohne erfolg ausprobiert. |
|
Back to top |
|
|
naitscho n00b
Joined: 12 May 2005 Posts: 20 Location: Germany
|
Posted: Tue Jan 10, 2006 2:50 pm Post subject: |
|
|
in /etc/conf.d/wireless:
Code: | essid_wlan0="WLAN"
key_WLAN="abcd-efgh-ijkl-mnop-1234-5678-90 enc restricted"
mode_wlan0="managed" |
in /etc/conf.d/net:
Code: | iface_wlan0="192.168.178.* netmask *.*.*.*"
gateway="wlan0/192.168.178.1" |
(das sind meine, evtl. restricted und managed anpassen, altes system, läuft aber zumindest, bin zu faul es anzupassen an die neue schreibweise, zum testen kannst du's ja mal nehmen)...
bei mir läuft der billig-stick mit zd1211 aus portage ganz gut, allerdings hängt sich das system ab und zu auf (glaube bei dauerlast, werd daher mal nen neueren kernel probieren und in den kernel-settings rumfummeln...) |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Tue Jan 10, 2006 9:38 pm Post subject: |
|
|
Was mir auch Sorgen macht, ist diese Meldung:
Code: |
Warning: Driver for device wlan0 has been compiled with version 19
of Wireless Extension, while this program supports up to version 17.
Some things may be broken...
|
Ich habe deine Einstellungen übernommen. Die essid wird jetzt automatisch angenommen. Der key und die Ip allerdings nicht.
iwconfig
Code: |
wlan0 802.11b/g NIC ESSID:"WLAN"
Mode:Managed Frequency=2.462 GHz Access Point: 00:00:00:00:00:00
Bit Rate:1 Mb/s
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=100/92 Signal level=15/154 Noise level=161/154
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:260 Invalid misc:0 Missed beacon:0
|
ifconfig
Code: |
wlan0 Link encap:Ethernet HWaddr 00:0E:2E:50:CF:0C
inet6 addr: fe80::20e:2eff:fe50:cf0c/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
|
Was auch sehr seltsam ist, ist die Tatsache, dass ich eine ipv6 Ip zugewisen bekomme, welche ich weder eingegeben habe, noch dass ipv6 support im Kernel aktiviert ist. Hier nochmal meine configs:
/etc/conf.d/net
Code: |
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /etc/conf.d/net.example and save your configuration
# in /etc/conf.d/net (this file :]!).
modules=( "iwconfig" )
config_wlan0=( "192.168.178.27 netmask 255.255.255.0" )
config_eth0=( "dhcp" )
routes=( "default via 192.168.178.1" )
|
/etc/conf.d/wireless
Code: |
essid_wlan0="WLAN"
key_WLAN="70616C6F6D696E6F70616C6F6D enc restricted"
mode_wlan0="managed"
|
|
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Tue Jan 10, 2006 11:04 pm Post subject: |
|
|
Das Wlan funktioniert jetzt endlich!
Ich habe kwifimanager-3.5.0 installiert und dort die Einstellungen angepasst.
Danach ein rc-update add net.wlan0 default, wenn der Rechner allerdings bootet, zeigt er mir an, dass er net.wlan0 nicht starten konnte. Nachdem alles geladen ist, muss ich net.wlan0 noch einmal neu starten, damit es funktioniert. Es wäre allerdings schön, direkt beim Start des Systems online zu sein. |
|
Back to top |
|
|
naitscho n00b
Joined: 12 May 2005 Posts: 20 Location: Germany
|
Posted: Wed Jan 11, 2006 3:10 pm Post subject: |
|
|
das mit der ipv6 hab ich glaube ich mit USE=-ipv6 oder so "gelöst" ; )
sprich rausgenommen komplett aus dem system, das machte mir auch probleme glaub ich,
das mit der fehlermeldung oben kannste glaub ich ignorieren |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Wed Jan 11, 2006 11:11 pm Post subject: |
|
|
Die Fehlermeldung habe ich durch die Installation von wireless-tools-28-pre3 entfernt. Das Problem bei einem USE-Flag wäre, dass ich den Treiber nicht über Portage installiert habe, sondern manuell. Das hat den einfach Grund, dass im Portage auch die unstable Packet ohne Patches kommen, welche aber auf der offiziellen seite als fertige Packages zum Download angeboten werden.
Das Package im Portage tree funktioniert auch nicht unter AMD64, die ptched Packete von http://zd1211.ath.cx allerdings schon.
Damit wären wir beim nächsten Thema: Ich hätte es gerne, wenn dieser Release in den Portage tree aufgenommen würde, da man diesem ~amd64 markieren kann. An wen muss ich mich dafür wenden? |
|
Back to top |
|
|
genstef Retired Dev
Joined: 13 Jun 2004 Posts: 668 Location: M/Bay/Germany
|
Posted: Thu Jan 12, 2006 2:24 pm Post subject: |
|
|
An besten meldest du dich im IRC #gentoo-laptop irc.freenode.net und/oder machst einen Bug mit deinem verbesserten Ebuild auf. |
|
Back to top |
|
|
genstef Retired Dev
Joined: 13 Jun 2004 Posts: 668 Location: M/Bay/Germany
|
Posted: Fri Jan 13, 2006 4:32 pm Post subject: |
|
|
Ich hab mal mit den amd64-Leuten geredet und die anderen, die es probiert haben meinen, dass es bei mehr load abstürzt, also zum Beispiel beim emerge sync. Kann nicht ~amd64 werden deswegen
Aber wenn das bei dir geht kannst du ja nochmal mit mir reden |
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Sat Jan 14, 2006 2:46 pm Post subject: |
|
|
So. Es gibt neues.
Wenn ich den Stick beim Systemstart rausnehme und wieder reinstecke, wird net.wlan0 problemlos gestartet. Also scheint es daran zu liegen, dass der Stick beim Start nicht korrekt erkannt wird. Hier mal meine dmesg:
Code: |
amp@gentoo ~ $ dmesg
Bootdata ok (command line is video=radeonfb:mtrr,ywrap,1280x1024-32@85 splash=verbose,theme:emergence quiet CONSOLE=/dev/tty1)
Linux version 2.6.14-gentoo-r5 (root@gentoo) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #11 Sat Jan 14 14:33:17 GMT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000faac0
ACPI: RSDT (v001 A M I OEMRSDT 0x10000409 MSFT 0x00000097) @ 0x000000001ff30000
ACPI: FADT (v001 A M I OEMFACP 0x10000409 MSFT 0x00000097) @ 0x000000001ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x10000409 MSFT 0x00000097) @ 0x000000001ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x10000409 MSFT 0x00000097) @ 0x000000001ff40040
ACPI: DSDT (v001 A0091 A0091006 0x00000006 MSFT 0x0100000d) @ 0x0000000000000000
On node 0 totalpages: 130767
DMA zone: 3999 pages, LIFO batch:1
Normal zone: 126768 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
Checking aperture...
CPU 0: aperture @ e0000000 size 256 MB
Built 1 zonelists
Kernel command line: video=radeonfb:mtrr,ywrap,1280x1024-32@85 splash=verbose,theme:emergence quiet CONSOLE=/dev/tty1
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2202.881 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 507524k/523456k available (3515k kernel code, 15048k reserved, 1546k data, 204k init)
Calibrating delay using timer specific routine.. 4415.77 BogoMIPS (lpj=8831554)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00
Using local APIC timer interrupts.
Detected 12.516 MHz APIC timer.
testing NMI watchdog ... OK.
checking if image is initramfs... it is
softlockup thread 0 started up.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xe0000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fd100000-fd6fffff
PREFETCH window: bff00000-dfefffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.24 [Flags: R/W DEBUG].
Initializing Cryptographic API
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=398.00 Mhz, System=300.00 MHz
radeonfb: PLL min 20000 max 40000
radeonfb: Monitor 1 type CRT found
radeonfb: Monitor 2 type no found
Console: switching to colour frame buffer device 160x64
fbsplash: console 0 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 0
radeonfb (0000:01:00.0): ATI Radeon AP
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1])
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 6.0.60-k2
Copyright (c) 1999-2005 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.4.14-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.41.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImExPS/2 Logitech Wheel Mouse on isa0060/serio1
hda: TOSHIBA DVD-ROM SD-M1502, ATAPI CD/DVD-ROM drive
hdb: TSSTcorpCD/DVDW TS-H552B, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X DVD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
libata version 1.12 loaded.
sata_via version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 1
sata_via(0000:00:0f.0): routed to hard irq line 1
ata1: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xD000 irq 177
ata2: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xD008 irq 177
ata1: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3c69 86:3e01 87:4003 88:80ff
ata1: dev 0 ATA, max UDMA7, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3c69 86:3e01 87:4003 88:80ff
ata2: dev 0 ATA, max UDMA7, 312581808 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_via
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 < sdb5 sdb6 sdb7 sdb8 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Fusion MPT base driver 3.03.03
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.03.03
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 9
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 185, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 05 Aug 2005
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 185, io base 0x0000b400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 185, io base 0x0000b800
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 185, io base 0x0000c000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 9
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 185, io base 0x0000c400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usb 1-7: new high speed USB device using ehci_hcd and address 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 193
ALSA device list:
#0: SBLive! Value [CT4832] (rev.8, serial:0x80271102) at 0xec00, irq 193
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
ACPI wakeup devices:
PCI0 PS2K PS2M UAR1 AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB
ACPI: (supports S0 S1 S3 S4 S5)
ReiserFS: sdb6: found reiserfs format "3.6" with standard journal
usb 3-1: new full speed USB device using uhci_hcd and address 2
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
ReiserFS: sdb6: using ordered data mode
ReiserFS: sdb6: journal params: device sdb6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb6: checking transaction log (sdb6)
ReiserFS: sdb6: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
Vendor: MSI Model: MS-5511 Rev: 0100
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sdc: 503552 512-byte hdwr sectors (258 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 503552 512-byte hdwr sectors (258 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 0
usb-storage: device scan complete
Adding 987956k swap on /dev/sdb8. Priority:-1 extents:1 across:987956k
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 193
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 193
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
zd1211 - http://zd1211.ath.cx/
Based on www.zydas.com.tw driver version 2.0.0.0
Release Ver = 4802
EEPORM Ver = 4330
PA type: 0
AllowedChannel = 000107ff
Region:48
usbcore: registered new driver zd1211
NTFS volume version 3.1.
NTFS-fs error (device sda1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdb5): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
usb 1-7: USB disconnect, address 3
zd1211_disconnect
fbsplash: console 1 using theme 'gentoo'
fbsplash: switched splash state to 'on' on console 1
fbsplash: console 2 using theme 'gentoo'
fbsplash: switched splash state to 'on' on console 2
fbsplash: console 3 using theme 'gentoo'
fbsplash: switched splash state to 'on' on console 3
fbsplash: console 4 using theme 'gentoo'
fbsplash: switched splash state to 'on' on console 4
fbsplash: console 5 using theme 'gentoo'
fbsplash: switched splash state to 'on' on console 5
usb 1-7: new high speed USB device using ehci_hcd and address 4
Release Ver = 4802
EEPORM Ver = 4330
PA type: 0
AllowedChannel = 000107ff
Region:48
power save disabed
****** Can't find desiredSSID:
keybuf data [0]:
Just Update WEP key
*** Sw to Infra
*** Sw to Infra
******* Schedule task fail *********
****** Can't find desiredSSID:
keybuf data [13]:
70 61 6c 6f 6d 69 6e 6f 70 61 6c 6f 6d
Update CardSetting
keybuf data [0]:
Update CardSetting
******* Schedule task fail *********
****** Can't find desiredSSID:WLAN
******* Schedule task fail *********
SSID element: data [6]:
00 04 57 4c 41 4e
SupportedRate element: data [6]:
01 04 82 84 8b 96
STA_ASSOCIATED
mac addr = 00:04:0e:5a:40:a0
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 425 MBytes.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
[fglrx] module loaded - fglrx 8.20.8 [Dec 6 2005] on minor 0
[fglrx] ACPI power management is initialized.
[fglrx] Internal AGP support requested, but kernel AGP support active.
[fglrx] Have to use kernel AGP support to avoid conflicts.
[fglrx] Kernel AGP support doesn't provide agplock functionality.
[fglrx] AGP detected, AgpState = 0x1f000a0a (hardware caps of chipset)
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f000302 (selected caps)
[fglrx] free AGP = 256126976
[fglrx] max AGP = 256126976
[fglrx] free LFB = 108974080
[fglrx] max LFB = 108974080
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 65536
|
|
|
Back to top |
|
|
Ampheus l33t
Joined: 19 Oct 2005 Posts: 814 Location: Rheine, NRW, Germany
|
Posted: Sat Jan 14, 2006 6:32 pm Post subject: |
|
|
Hinzufügen von "Loadable Module support -> Automatic Kernel Module loading" im Kernel hat den gewünschten erfolg gebracht. Danke nochmal an euch, jetzt bin ich der Einzige, der den zd1211 unter amd64 stable am laufen hat.
Falls jemand Fragen diesbezüglich hat, #zd1211 @freenode. Schreibt mir einfach. |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|