Gentoo Forums :: View topic - [solved] PCMCIA with Medion 41700

[solved] PCMCIA with Medion 41700

View unanswered posts
View posts from last 24 hours

Gentoo Forums Forum Index

Kernel & Hardware

View previous topic :: View next topic

Author

Message

Jens Pranaitis
n00b
n00b

Joined: 17 Jan 2005
Posts: 10
Location: Oberhausen, Germany

Posted: Fri Jan 27, 2006 12:50 pm Post subject: [solved] PCMCIA with Medion 41700

WORKS
The rt2500 drivers in portage were the problem, using the drivers from cvs everything works

I've got a Medion MD 41700 notebook, with a Texas Instruments PCI7420 CardBus Controller. I bought myself a Edimax 7108PCg wifi card, the datasheet is available here. The card has a Ralink rt2500 chip. I built all pcmcia modules availible in the vanilla-sources and emerged coldplug. Coldplug loads the yenta_socket and the rsrc_nonstatic modules. When the yenta_socket module is loaded the link LED of my card flashes. I emerged pcmciautils, the pccardctl utility reports:

Code:

mobile jens # pccardctl status
Socket 0:
no card
Socket 1:
3.3V 32-bit PC Card

pccardctl ident 1 reports that no product information is available. When I load the rt2500 module nothing happens.

Additional information:
lspci -vv

Code:

01:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge (rev 02)
Subsystem: Wistron Corp. Unknown device 1234
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [a0] AGP version 3.0
   Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
   Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01) (prog-if 10 [OHCI])
Subsystem: Wistron Corp. Unknown device 4037
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0001000 (32-bit, non-prefetchable) [size=4K]

00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev 01) (prog-if 10 [OHCI])
Subsystem: Wistron Corp. Unknown device 4037
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0002000 (32-bit, non-prefetchable) [size=4K]

00:13.2 USB Controller: ATI Technologies Inc EHCI USB Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Wistron Corp. Unknown device 4037
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
   Bridge: PM- B3+

00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 18)
Subsystem: Wistron Corp. Unknown device 4039
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 8060 [size=16]
Region 1: Memory at d0004000 (32-bit, non-prefetchable) [size=1K]

00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE Controller (prog-if 8a [Master SecP PriP])
Subsystem: Wistron Corp. Unknown device 4038
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 8070 [size=16]

00:14.3 ISA bridge: ATI Technologies Inc Unknown device 434c
Subsystem: Wistron Corp. Unknown device 4037
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:14.4 PCI bridge: ATI Technologies Inc Unknown device 4342 (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=04, sec-latency=168
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d0200000-d02fffff
Prefetchable memory behind bridge: 40000000-44ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
Subsystem: Wistron Corp. Unknown device 2014
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at d0004400 (32-bit, non-prefetchable) [size=256]

00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01) (prog-if 00 [Generic])
Subsystem: Wistron Corp. Unknown device 10a2
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at d0004800 (32-bit, non-prefetchable) [size=256]

01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP [Radeon Mobility 9100IGP] (prog-if 00 [VGA])
Subsystem: Wistron Corp. Unknown device 206d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
   Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit+ FW+ AGP3+ Rate=x4,x8
   Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:04.0 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
Subsystem: Wistron Corp. Unknown device 3005
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0208000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 40000000-41fff000 (prefetchable)
Memory window 1: 46000000-47fff000
I/O window 0: 0000a400-0000a4ff
I/O window 1: 0000a800-0000a8ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001

02:04.1 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
Subsystem: Wistron Corp. Unknown device 3005
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin B routed to IRQ 11
Region 0: Memory at d0209000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 42000000-43fff000 (prefetchable)
Memory window 1: 48000000-49fff000
I/O window 0: 0000ac00-0000acff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001

02:04.2 FireWire (IEEE 1394): Texas Instruments PCI7x20 1394a-2000 OHCI Two-Port PHY/Link-Layer Controller (prog-if 10 [OHCI])
Subsystem: Wistron Corp. Unknown device 1095
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size 08
Interrupt: pin C routed to IRQ 11
Region 0: Memory at d0206000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME+

02:04.3 Mass storage controller: <pci_lookup_name: buffer too small>
Subsystem: Wistron Corp. Unknown device 3006
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size 08
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d0207000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Wistron Corp. Unknown device 1053
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at d0206800 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 44000000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:06.0 Network controller: Intersil Corporation ISL3886 [Prism Javelin/Prism Xbow] (rev 01)
Subsystem: Z-Com, Inc. Unknown device 0036
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 56 (2500ns min, 7000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0204000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [dc] Power Management version 1
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

dmesg

Code:

Linux version 2.6.14.6 (root@mobile) (gcc-Version 3.4.5 (Gentoo 3.4.5, ssp-3.4.5-1.0, pie-8.7.9)) #4 PREEMPT Fri Jan 20 14:27:39 CET 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002bf70000 (usable)
BIOS-e820: 000000002bf70000 - 000000002bf77000 (ACPI data)
BIOS-e820: 000000002bf77000 - 000000002bf80000 (ACPI NVS)
BIOS-e820: 000000002bf80000 - 000000002c000000 (reserved)
BIOS-e820: 000000003bf80000 - 000000003c000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
703MB LOWMEM available.
On node 0 totalpages: 180080
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 175984 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6a20
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x2bf72bd3
ACPI: FADT (v001 ATI Chinook 0x06040000 ATI 0x000f4240) @ 0x2bf76f32
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x2bf76fa6
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x2bf72e02
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x2bf72c07
ACPI: DSDT (v001 ATI SB200 0x06040000 MSFT 0x0100000e) @ 0x00000000
Allocating PCI resources starting at 40000000 (gap: 3c000000:c2c00000)
Built 1 zonelists
Kernel command line: root=/dev/hda2
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2600.380 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 709284k/720320k available (2762k kernel code, 10516k reserved, 791k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5205.55 BogoMIPS (lpj=10411111)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
mtrr: v2.0 (20020519)
CPU: Intel(R) Celeron(R) CPU 2.60GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd788, last bus=4
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 10 *11)
ACPI: Embedded Controller [EC0] (gpe 3)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:06: ioport range 0x2e8-0x2e9 has been reserved
pnp: 00:06: ioport range 0x1080-0x1080 has been reserved
pnp: 00:06: ioport range 0x220-0x22f could not be reserved
pnp: 00:06: ioport range 0x40b-0x40b has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: d0100000-d01fffff
PREFETCH window: e0000000-e7ffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 0000a400-0000a4ff
IO window: 0000a800-0000a8ff
PREFETCH window: 40000000-41ffffff
MEM window: 46000000-47ffffff
PCI: Bus 7, cardbus bridge: 0000:02:04.1
IO window: 0000ac00-0000acff
IO window: 00001400-000014ff
PREFETCH window: 42000000-43ffffff
MEM window: 48000000-49ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: d0200000-d02fffff
PREFETCH window: 40000000-44ffffff
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:02:04.1 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1138360406.580:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
vesafb: ATI Technologies Inc., MS3 , 01.00 (OEM: ATI MOBILITY RADEON 9100 IGP)
vesafb: VBE version: 2.0
vesafb: no monitor limits have been set
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
vesafb: framebuffer at 0xe0000000, mapped to 0xec880000, using 6144k, total 65536k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Medion 41700 detected - limiting to C1 max_cstate. Override with "processor.max_cstate=9"
ACPI: processor limited to max C-state 1
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRC] (22 C)
ACPI: Thermal Zone [THRS] (17 C)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Ati IGP9100/M chipset
agpgart: AGP aperture is 128M @ 0xd8000000
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.17.0 20050311 on minor 0:
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt for device 0000:00:14.6 disabled
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:05.0[A] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xa000, 00:0a:e4:52:76:ac, IRQ 11
eth0: Identified 8139 chip type 'RTL-8101'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNK0] -> GSI 11 (level, low) -> IRQ 11
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8070-0x8077, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8078-0x807f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N040ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVD-RW GWA-4040N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/1740KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:04.2[C] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[d0206000-d02067ff] Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 11, io mem 0xd0003000
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 11, io mem 0xd0001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 11, io mem 0xd0002000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).
ALSA device list:
No soundcards found.
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
LID0 LANC AUDO MODM
ACPI: (supports S0 S3 S4 S5)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[131036ab000ae404]
input: AT Translated Set 2 keyboard on isa0060/serio0
EXT3-fs: hda2: orphan cleanup on readonly fs
kjournald starting. Commit interval 5 seconds
ext3_orphan_cleanup: deleting unreferenced inode 557453
EXT3-fs: hda2: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 256k freed
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
EXT3 FS on hda2, internal journal
Acer Travelmate hotkey driver v0.5.31
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 511992k swap on /swap. Priority:-1 extents:132 across:520844k
ACPI: PCI Interrupt 0000:00:14.5[B] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:04.0 [17c0:3005]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x010a1b22, devctl 0x66
Yenta: ISA IRQ mask 0x04f8, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x44ffffff
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNK3] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:04.1 [17c0:3005]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x010a1b22, devctl 0x66
Yenta: ISA IRQ mask 0x04f8, PCI irq 11
Socket status: 30000820
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x44ffffff
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ndiswrapper version 1.8 loaded (preempt=yes,smp=no)
ndiswrapper: driver prisma00 (GlobespanVirata,12/05/2003, 2.1.14.2) loaded
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11
ndiswrapper: using irq 11
spurious 8259A interrupt: IRQ7.
wlan0: vendor: 'PRISM 802.11g Wireless Adapter'
wlan0: ndiswrapper ethernet device 00:60:b3:a6:5e:79 using driver prisma00, 1260:3886:17CF:0036.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
ndiswrapper (iw_set_tx_power:450): setting tx_power failed (C00000BB)

Thanks, Jens.

Last edited by Jens Pranaitis on Wed Apr 19, 2006 10:51 am; edited 1 time in total

Jens Pranaitis
n00b
n00b

Joined: 17 Jan 2005
Posts: 10
Location: Oberhausen, Germany

Posted: Tue Jan 31, 2006 2:47 pm Post subject:

bump

avx
Advocate

Joined: 21 Jun 2004
Posts: 2152

Posted: Tue Jan 31, 2006 2:48 pm Post subject:

Someone able to help? My dad has the same problems (Nice jensp, bumping nearly simultaneous.)

no_hope
Guru
Guru

Joined: 23 Jun 2003
Posts: 482

Posted: Fri Feb 03, 2006 2:47 am Post subject:

I think I had a similar problem. I tried many things and I think the problem was with the kernel PCMCIA support. My wild guess is that the kernel does not inform the driver that the card is inserted. Try emerging pcmcia-cs and then run cardmgr. I think that's what solved my problem.

Display posts from previous:

	Gentoo Forums Forum Index Kernel & Hardware	All times are GMT
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Copyright 2001-2025 Gentoo Foundation, Inc. Designed by Kyle Manna © 2003; Style derived from original subSilver theme. | Hosting by Gossamer Threads Inc. © | Powered by phpBB 2.0.23-gentoo-p11 © 2001, 2002 phpBB Group
Privacy Policy