KPC650 - USB HC Takeover Failed

[luftegrof]

I've been working on this problem for a long time without any success. I'm asking for help now that I've exhausted my mind. Can anyone help me troubleshoot this problem?

-Dell Inspiron 6000
-BIOS Rev. A09 (upgraded from A06 when this problem began)
-Kyocera KPC650 (Verizon Wireless) PCMCIA
-Gentoo 2005.1 (updated often)
-Kernel 2.6.15 from gentoo-sources r1 (>=2.6.12 have been attempted)
-Module parameters 'ohci_hcd.no_handshake=1' and 'usbcore.old_scheme_first=Y' were tweaked with no effect.
-ACPI and APIC enabled or disabled, problem still occurs.
-USB (lsusb) does not see the card.
-I have tested this card on the same laptop with a different linux distribution (slax and ubuntu) resulting with the same problem.
-I have tested this card on different laptops and it works with linux or windows.

Here's the dmesg output after the card is inserted:

pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:04:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:04:00.0 to 64
ohci_hcd 0000:04:00.0: OHCI Host Controller
ohci_hcd 0000:04:00.0: USB HC takeover failed! (BIOS/SMM bug)
ohci_hcd 0000:04:00.0: can't reset
ACPI: PCI interrupt for device 0000:04:00.0 disabled
ohci_hcd 0000:04:00.0: init 0000:04:00.0 fail, -16
ohci_hcd: probe of 0000:04:00.0 failed with error -16
PCI: Enabling device 0000:04:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:04:00.1 to 64
ohci_hcd 0000:04:00.1: OHCI Host Controller
ohci_hcd 0000:04:00.1: USB HC takeover failed! (BIOS/SMM bug)
ohci_hcd 0000:04:00.1: can't reset
ACPI: PCI interrupt for device 0000:04:00.1 disabled
ohci_hcd 0000:04:00.1: init 0000:04:00.1 fail, -16
ohci_hcd: probe of 0000:04:00.1 failed with error -16
PCI: Enabling device 0000:04:00.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:04:00.2[C] -> GSI 19 (level, low) -> IRQ 16
ehci_hcd 0000:04:00.2: EHCI Host Controller
ehci_hcd 0000:04:00.2: new USB bus registered, assigned bus number 6
ehci_hcd 0000:04:00.2: irq 16, io mem 0x52002000
ehci_hcd 0000:04:00.2: startup error -19
ehci_hcd 0000:04:00.2: USB bus 6 deregistered
ACPI: PCI interrupt for device 0000:04:00.2 disabled
ehci_hcd 0000:04:00.2: init 0000:04:00.2 fail, -19

Here's my "lspci -v" output:
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
Subsystem: Dell Unknown device 0188
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA])
Subsystem: Dell Unknown device 0188
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at dff00000 (32-bit, non-prefetchable) [size=512K]
I/O ports at ec38 [size=8]
Memory at c0000000 (32-bit, prefetchable) [size=256M]
Memory at dfec0000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2

00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
Subsystem: Dell Unknown device 0188
Flags: bus master, fast devsel, latency 0
Memory at dff80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2

00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at bf80 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 0, IRQ 17
I/O ports at bf60 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at bf40 [size=32]

00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at bf20 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 0, IRQ 19
Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=04, sec-latency=32
Memory behind bridge: dfd00000-dfdfffff
Prefetchable memory behind bridge: 0000000050000000-0000000051f00000
Capabilities: [50] #0d [0000]

00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
Subsystem: Dell Inspiron 6000 laptop
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at ed00 [size=256]
I/O ports at ec40 [size=64]
Memory at dfebfe00 (32-bit, non-prefetchable) [size=512]
Memory at dfebfd00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 0

00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 03) (prog-if 80 [Master])
Subsystem: Dell Unknown device 0188
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at bfa0 [size=16]
Capabilities: [70] Power Management version 2

03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Subsystem: Dell Inspiron 6000 laptop
Flags: bus master, fast devsel, latency 64, IRQ 18
Memory at dfdfe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2

03:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
Subsystem: Dell Inspiron 6000 laptop
Flags: bus master, medium devsel, latency 168, IRQ 16
Memory at dfd00000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 50000000-51fff000 (prefetchable)
Memory window 1: 52000000-53fff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
16-bit legacy interface ports at 0001

03:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) (prog-if 10 [OHCI])
Subsystem: Dell Unknown device 0188
Flags: bus master, medium devsel, latency 64, IRQ 18
Memory at dfdfc800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2

03:01.2 Class 0805: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17) (prog-if 01)
Subsystem: Dell Inspiron 6000 laptop
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at dfdfc700 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2

03:03.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
Subsystem: Intel Corporation Unknown device 2721
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at dfdfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2

04:00.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: Edimax Computer Co. Unknown device 0031
Flags: medium devsel, IRQ 16
Memory at 52000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

04:00.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: Eltec Elektronik GmbH Unknown device 027d
Flags: medium devsel, IRQ 16
Memory at 52001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

04:00.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: Unknown device 1833:00e0
Flags: medium devsel, IRQ 16
[virtual] Memory at 52002000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [40] Power Management version 2


Here's my normal dmesg without the card inserted:

Linux version 2.6.15-gentoo-r1 (root@lappy) (gcc version 3.3.6 (Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #5 PREEMPT Thu Jan 26 23:56:58 ES
T 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7d3800 (usable)
BIOS-e820: 000000003f7d3800 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved)
BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 260051
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 30675 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000fc9b0
ACPI: RSDT (v001 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d3fd3
ACPI: FADT (v001 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d4c00
ACPI: MADT (v001 DELL CPi R 0x27d5091c ASL 0x00000047) @ 0x3f7d5400
ACPI: MCFG (v016 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d53c0
ACPI: BOOT (v001 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d4fc0
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20030522) @ 0x3f7d43e6
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030522) @ 0x3f7d420e
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030522) @ 0x3f7d4013
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists
Kernel command line:
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1596.242 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1026792k/1040204k available (2554k kernel code, 12772k reserved, 816k data, 184k init, 122700k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3196.74 BogoMIPS (lpj=6393481)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbaae, last bus=10
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1080-10bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 *7 9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Failed to allocate I/O resource #7:1000@10000 for 0000:00:1e.0
PCI: Bus 4, cardbus bridge: 0000:03:01.0
IO window: 00001400-000014ff
IO window: 00001800-000018ff
PREFETCH window: 50000000-51ffffff
MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: dfd00000-dfdfffff
PREFETCH window: 50000000-51ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:03:01.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 16
Simple Boot Flag at 0x79 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1138455385.132:1): initialized
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (49 C)
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
[drm] Initialized drm 1.0.0 20040925
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
mice: PS/2 mouse device common for all mice
Floppy drive(s): fd0 is 1.44M
input: AT Translated Set 2 keyboard as /class/input/input0
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
floppy0: no floppy controllers found
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: SONY CD-RW/DVD-ROM CRX830E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14
ata1: dev 0 cfg 49:2b00 82:346b 83:5b29 84:4003 85:346b 86:1a09 87:4003 88:203f
ata1: dev 0 ATA-6, max UDMA/100, 156301488 sectors: LBA
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: FUJITSU MHT2080A Rev: 0022
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.4 (8126 buckets, 65008 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
LID PBTN PCI0 USB0 USB1 USB2 USB4 USB3 MODM PCIE
ACPI: (supports S0 S3 S4 S5)
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
EXT3-fs: recovery complete.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Adding 506008k swap on /dev/sda6. Priority:-1 extents:1 across:506008k
EXT3 FS on sda5, internal journal
ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:03:01.0 [1028:0188]
Yenta: ISA IRQ mask 0x04b8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge Memory window: 0xdfd00000 - 0xdfdfffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
b44.c:v0.97 (Nov 30, 2005)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: Broadcom 4400 10/100BaseT Ethernet 00:11:43:6d:c3:2d
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.1.6
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.8
ipw2200: Copyright(c) 2003-2005 Intel Corporation
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232
usbcore: registered new driver mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
cdrom: open failed.
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
cdrom: open failed.
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bf80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000bf20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa80800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 55505 usecs
intel8x0: clocking to 48000
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[dfdfc800-dfdfcfff] Max Packet=[2048]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[324fc00020a268c1]
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is on for TX and on for RX.
mtrr: no more MTRRs available