| View previous topic :: View next topic |
| Author |
Message |
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
 Posted: Fri Feb 17, 2006 3:08 pm Post subject: iBook 12" - dual usb - help about internal modem [solve |
 |
|
Hi there ... 
I`ve been using gentoo on this iBook ( 12", dual usb , 500 MHz ) for a while .. amd i have manage to setup almost everything ..
So .. let`s cut to the chase . . ..
HOW to setup internal modem ??
As far as i can see, i don`t see it ..
| Code: | matrix playahater # lspci -v
00:0b.0 Host bridge: Apple Computer Inc. UniNorth/Pangea AGP
Flags: bus master, 66MHz, medium devsel, latency 16
Capabilities: [80] AGP version 1.0
00:10.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev 02) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Mobility M3 AGP 2x
Flags: bus master, stepping, 66MHz, medium devsel, latency 255, IRQ 48
Memory at 94000000 (32-bit, prefetchable) [size=64M]
I/O ports at f0000400 [size=256]
Memory at 90000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at f1000000 [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2
0001:10:0b.0 Host bridge: Apple Computer Inc. UniNorth/Pangea PCI
Flags: bus master, 66MHz, medium devsel, latency 16
0001:10:17.0 Class ff00: Apple Computer Inc. KeyLargo/Pangea Mac I/O
Flags: bus master, medium devsel, latency 16
Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
0001:10:18.0 USB Controller: Apple Computer Inc. KeyLargo/Pangea USB (prog-if 10 [OHCI])
Flags: bus master, medium devsel, latency 16, IRQ 27
Memory at 80081000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
0001:10:19.0 USB Controller: Apple Computer Inc. KeyLargo/Pangea USB (prog-if 10 [OHCI])
Flags: bus master, medium devsel, latency 16, IRQ 28
Memory at 80080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
0002:20:0b.0 Host bridge: Apple Computer Inc. UniNorth/Pangea Internal PCI
Flags: bus master, 66MHz, medium devsel, latency 16
0002:20:0e.0 FireWire (IEEE 1394): Apple Computer Inc. UniNorth/Pangea FireWire (prog-if 10 [OHCI])
Subsystem: Apple Computer Inc. UniNorth/Pangea FireWire
Flags: bus master, 66MHz, medium devsel, latency 16, IRQ 40
Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
0002:20:0f.0 Ethernet controller: Apple Computer Inc. UniNorth/Pangea GMAC (Sun GEM)
Flags: bus master, 66MHz, slow devsel, latency 16, IRQ 41
Memory at f5200000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at f5100000 [disabled] [size=1M]
matrix playahater #
|
| Code: | matrix playahater # lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
matrix playahater #
|
How do i need to compile the kernel ??
My kernel .conf is here .. at the bootom of the page
https://forums.gentoo.org/viewtopic-t-417093-postdays-0-postorder-asc-start-25.html
I assume that i need ppp, wvdial and properly configured kernel in order to have dialup internet ??
10x in advance
Cheers
_________________
http://droopia.net
Last edited by playahater on Mon Jun 05, 2006 9:22 pm; edited 1 time in total |
|
| Back to top |
|
 |
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Mon Mar 20, 2006 11:19 pm Post subject: |
|
|
OK .. me again ..
i have been trying to set up internal modem but no luck ..
i have emerge wvdial with all dependencies and .. i think i have compiled kernel properly .. but .. 
i have serial devices like
| Code: |
playahater@matrix ~ $ ls /dev/ |grep ttyS
ttyS0
ttyS1
ttyS2
ttyS3
playahater@matrix ~ $
|
but when i try to run wvdialconf I get an error .. 
| Code: |
playahater@matrix ~ $ wvdialconf ~/.wvdial.conf
Editing `/home/playahater/.wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<Info>: Device or resource busy
Modem Port Scan<*1>: S0
ttyS1<Info>: Device or resource busy
Modem Port Scan<*1>: S1
ttyS2<Info>: Device or resource busy
Modem Port Scan<*1>: S2
ttyS3<Info>: Device or resource busy
Modem Port Scan<*1>: S3
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http://open.nit.ca/wiki/?WvDial
If you still have problems, send mail to <wvdial-list@lists.nit.ca>.
playahater@matrix ~ $
|
So .. anyone know how to solve this ?? .. Do i need to install some drivers ??
I`ve been searching for solution but no luck ..
i have found here in forum that some people have solved the problem just with compiling the right serial device into kernel but that doesn`t do the job for me ..
Any idea .. i really need this modem ??
10x in advance
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Tue Mar 21, 2006 1:36 pm Post subject: |
|
|
no ideas ??
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
JoseJX
Retired Dev
Joined: 28 Apr 2002
Posts: 2774
|
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Tue Mar 21, 2006 5:59 pm Post subject: |
|
|
well .. i had ubuntu and debian for ppc and it worked .. so there must be a way to set it under gentoo, too.
and as far as i remeber i didn`t have to install any drivers .. all i had to do was to link modem device to ttys0 .. which in this case isn`t gonna work .. 
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
JoseJX
Retired Dev
Joined: 28 Apr 2002
Posts: 2774
|
| Posted: Tue Mar 21, 2006 6:15 pm Post subject: |
|
|
Ah, then you have the iBook 500 with a hardware modem. (There were two versions, the later had a software modem). This is the same modem as my TiBook, using the serial driver mentioned in the FAQ (make sure you have i2c support enabled as well) worked perfectly.
Please make sure you've got that driver in your kernel, then look for the messages regarding the serial ports in dmesg to be sure that it's loaded correctly.
_________________
Gentoo PPC FAQ: http://www.gentoo.org/doc/en/gentoo-ppc-faq.xml |
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Tue Mar 21, 2006 6:16 pm Post subject: |
|
|
here`s what i found ..
| Quote: |
Apple uses hardware-driven modems in every mac up to the pre-flat panel iMac, early PowerMac G4, early PowerBook G4 and iBook G3 500 MHz, the eMac and all iMac/iBooks, PowerMac/PowerBooks newer than those listed before uses softmodems.
|
_________________
http://droopia.net |
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Tue Mar 21, 2006 6:19 pm Post subject: |
|
|
| JoseJX wrote: | Ah, then you have the iBook 500 with a hardware modem. (There were two versions, the later had a software modem). This is the same modem as my TiBook, using the serial driver mentioned in the FAQ (make sure you have i2c support enabled as well) worked perfectly.
Please make sure you've got that driver in your kernel, then look for the messages regarding the serial ports in dmesg to be sure that it's loaded correctly. |
yes .. that`s correct .. i have ibook 500Mhz .. 12" .. .. and i`m pretty sure that i have compiled kernel right .. and i have been watching dmesg but unfortunatelly no serial loaded .. and that`s what was bugging me the most ..
My kernel .conf is here .. at the bootom of the page ..
https://forums.gentoo.org/viewtopic-t-417093-postdays-0-postorder-asc-start-25.html
10 in advance
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
JoseJX
Retired Dev
Joined: 28 Apr 2002
Posts: 2774
|
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Tue Mar 21, 2006 8:00 pm Post subject: |
|
|
| JoseJX wrote: | | Please post your dmesg too. |
of course
| Code: |
matrix / # cat /var/log/messages
Jan 5 08:47:14 matrix syslog-ng[5241]: syslog-ng version 1.6.8 starting
Jan 5 08:47:14 matrix syslog-ng[5241]: Changing permissions on special file /dev/tty12
Jan 5 08:47:14 matrix Total memory = 256MB; using 512kB for hash table (at c0600000)
Jan 5 08:47:14 matrix Linux version 2.6.14-gentoo-r5 (root@livecd) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #5 Sun Jan 1 21:31:34 CET 2006
Jan 5 08:47:14 matrix Found UniNorth memory controller & host bridge, revision: 192
Jan 5 08:47:14 matrix Mapped at 0xfdf00000
Jan 5 08:47:14 matrix Found a Pangea mac-io controller, rev: 0, mapped at 0xfde80000
Jan 5 08:47:14 matrix Processor NAP mode on idle enabled.
Jan 5 08:47:14 matrix PowerMac motherboard: iBook 2
Jan 5 08:47:14 matrix Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
Jan 5 08:47:14 matrix Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Jan 5 08:47:14 matrix Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
Jan 5 08:47:14 matrix via-pmu: Server Mode is disabled
Jan 5 08:47:14 matrix PMU driver 2 initialized for Core99, firmware: 0c
Jan 5 08:47:14 matrix nvram: Checking bank 0...
Jan 5 08:47:14 matrix nvram: gen0=654, gen1=655
Jan 5 08:47:14 matrix nvram: Active bank is: 1
Jan 5 08:47:14 matrix nvram: OF partition at 0x210
Jan 5 08:47:14 matrix nvram: XP partition at 0x1220
Jan 5 08:47:14 matrix nvram: NR partition at 0x1320
Jan 5 08:47:14 matrix On node 0 totalpages: 65536
Jan 5 08:47:14 matrix DMA zone: 65536 pages, LIFO batch:31
Jan 5 08:47:14 matrix Normal zone: 0 pages, LIFO batch:1
Jan 5 08:47:14 matrix HighMem zone: 0 pages, LIFO batch:1
Jan 5 08:47:14 matrix Built 1 zonelists
Jan 5 08:47:14 matrix Kernel command line: root=/dev/hda4 ro
Jan 5 08:47:14 matrix PowerMac using OpenPIC irq controller at 0x80040000
Jan 5 08:47:14 matrix OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc62f000
Jan 5 08:47:14 matrix OpenPIC timer frequency is 4.160000 MHz
Jan 5 08:47:14 matrix PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan 5 08:47:14 matrix GMT Delta read from XPRAM: 480 minutes, DST: off
Jan 5 08:47:14 matrix time_init: decrementer frequency = 16.640000 MHz
Jan 5 08:47:14 matrix Console: colour dummy device 80x25
Jan 5 08:47:14 matrix pmac_zilog: i2c-modem detected, id: 1
Jan 5 08:47:14 matrix Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan 5 08:47:14 matrix Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan 5 08:47:14 matrix Memory: 253056k available (3892k kernel code, 1676k data, 220k init, 0k highmem)
Jan 5 08:47:14 matrix AGP special page: 0xcffff000
Jan 5 08:47:14 matrix Calibrating delay loop... 997.37 BogoMIPS (lpj=1994752)
Jan 5 08:47:14 matrix Mount-cache hash table entries: 512
Jan 5 08:47:14 matrix device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,750@0
Jan 5 08:47:14 matrix softlockup thread 0 started up.
Jan 5 08:47:14 matrix NET: Registered protocol family 16
Jan 5 08:47:14 matrix PCI: Probing PCI hardware
Jan 5 08:47:14 matrix Registering openpic with sysfs...
Jan 5 08:47:14 matrix SCSI subsystem initialized
Jan 5 08:47:14 matrix usbcore: registered new driver usbfs
Jan 5 08:47:14 matrix usbcore: registered new driver hub
Jan 5 08:47:14 matrix Thermal assist unit using timers, shrink_timer: 500 jiffies
Jan 5 08:47:14 matrix Registering PowerMac CPU frequency driver
Jan 5 08:47:14 matrix Low: 400 Mhz, High: 499 Mhz, Boot: 499 Mhz
Jan 5 08:47:14 matrix Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jan 5 08:47:14 matrix NTFS driver 2.1.24 [Flags: R/W].
Jan 5 08:47:14 matrix Initializing Cryptographic API
Jan 5 08:47:14 matrix Generic RTC Driver v1.07
Jan 5 08:47:14 matrix Macintosh non-volatile memory driver v1.1
Jan 5 08:47:14 matrix Linux agpgart interface v0.101 (c) Dave Jones
Jan 5 08:47:14 matrix agpgart: Detected Apple UniNorth/Pangea chipset
Jan 5 08:47:14 matrix agpgart: configuring for size idx: 4
Jan 5 08:47:14 matrix agpgart: AGP aperture is 16M @ 0x0
Jan 5 08:47:14 matrix [drm] Initialized drm 1.0.0 20040925
Jan 5 08:47:14 matrix PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
Jan 5 08:47:14 matrix [drm] Initialized r128 2.5.0 20030725 on minor 0:
Jan 5 08:47:14 matrix aty128fb: Invalid ROM signature 6373 should be 0xaa55
Jan 5 08:47:14 matrix aty128fb: BIOS not located, guessing timings.
Jan 5 08:47:14 matrix aty128fb: Rage128 LF M3 AGP [chip rev 0x0] 8M 128-bit SDR SGRAM (1:1)
Jan 5 08:47:14 matrix Console: switching to colour frame buffer device 128x48
Jan 5 08:47:14 matrix Registered "ati" backlight controller,level: 15/15
Jan 5 08:47:14 matrix fb0: ATY Rage128 frame buffer device on Rage128 LF M3 AGP
Jan 5 08:47:14 matrix IN from bad port 64 at c0223978
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix IN from bad port 60 at c02239c8
Jan 5 08:47:14 matrix IN from bad port 64 at c0223a20
Jan 5 08:47:14 matrix i8042.c: No controller found.
Jan 5 08:47:14 matrix Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Jan 5 08:47:14 matrix IN from bad port 3f9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 3f9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 3f9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 2f9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 2f9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 2f9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 3e9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 3e9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 3e9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 2e9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 2e9 at c0228cb8
Jan 5 08:47:14 matrix IN from bad port 2e9 at c0228cb8
Jan 5 08:47:14 matrix pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
Jan 5 08:47:14 matrix pmac_zilog: Error registering serial device, disabling pmac_zilog.
Jan 5 08:47:14 matrix pmac_zilog: Did another serial driver already claim the minors?
Jan 5 08:47:14 matrix mice: PS/2 mouse device common for all mice
Jan 5 08:47:14 matrix input: PC Speaker
Jan 5 08:47:14 matrix io scheduler noop registered
Jan 5 08:47:14 matrix io scheduler anticipatory registered
Jan 5 08:47:14 matrix io scheduler deadline registered
Jan 5 08:47:14 matrix io scheduler cfq registered
Jan 5 08:47:14 matrix RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Jan 5 08:47:14 matrix loop: loaded (max 8 devices)
Jan 5 08:47:14 matrix sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
Jan 5 08:47:14 matrix PHY ID: 4061e3, addr: 0
Jan 5 08:47:14 matrix eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:06:4a:84
Jan 5 08:47:14 matrix eth0: Found BCM5221 PHY
Jan 5 08:47:14 matrix PPP generic driver version 2.4.2
Jan 5 08:47:14 matrix PPP Deflate Compression module registered
Jan 5 08:47:14 matrix PPP BSD Compression module registered
Jan 5 08:47:14 matrix NET: Registered protocol family 24
Jan 5 08:47:14 matrix MacIO PCI driver attached to Pangea chipset
Jan 5 08:47:14 matrix input: Macintosh mouse button emulation
Jan 5 08:47:14 matrix apm_emu: APM Emulation 0.5 initialized.
Jan 5 08:47:14 matrix Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Jan 5 08:47:14 matrix ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jan 5 08:47:14 matrix adb: starting probe task...
Jan 5 08:47:14 matrix adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
Jan 5 08:47:14 matrix ADB keyboard at 2, handler 1
Jan 5 08:47:14 matrix Detected ADB keyboard, type ISO, swapping keys.
Jan 5 08:47:14 matrix input: ADB keyboard on adb2:2.c4/input
Jan 5 08:47:14 matrix input: ADB Powerbook buttons on adb7:7.1f/input
Jan 5 08:47:14 matrix ADB mouse at 3, handler set to 4 (trackpad)
Jan 5 08:47:14 matrix input: ADB mouse on adb3:3.01/input
Jan 5 08:47:14 matrix adb: finished probe task...
Jan 5 08:47:14 matrix ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2, irq 19
Jan 5 08:47:14 matrix Probing IDE interface ide0...
Jan 5 08:47:14 matrix hda: TOSHIBA MK1017GAP, ATA DISK drive
Jan 5 08:47:14 matrix hdb: SONY CD-RW CRX700E, ATAPI CD/DVD-ROM drive
Jan 5 08:47:14 matrix hda: Enabling Ultra DMA 2
Jan 5 08:47:14 matrix hdb: Enabling MultiWord DMA 2
Jan 5 08:47:14 matrix ide0 at 0xd1006000-0xd1006007,0xd1006160 on irq 19
Jan 5 08:47:14 matrix hda: max request size: 128KiB
Jan 5 08:47:14 matrix hda: 19640880 sectors (10056 MB), CHS=19485/16/63, UDMA(33)
Jan 5 08:47:14 matrix hda: cache flushes not supported
Jan 5 08:47:14 matrix hda: [mac] hda1 hda2 hda3 hda4
Jan 5 08:47:14 matrix hdb: ATAPI 24X CD-ROM CD-R/RW drive, 8192kB Cache, DMA
Jan 5 08:47:14 matrix Uniform CD-ROM driver Revision: 3.20
Jan 5 08:47:14 matrix eth0: Link is up at 10 Mbps, half-duplex.
Jan 5 08:47:14 matrix ide-floppy driver 0.99.newide
Jan 5 08:47:14 matrix mesh: configured for synchronous 5 MB/s
Jan 5 08:47:14 matrix st: Version 20050830, fixed bufsize 32768, s/g segs 256
Jan 5 08:47:14 matrix ieee1394: Initialized config rom entry `ip1394'
Jan 5 08:47:14 matrix ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
Jan 5 08:47:14 matrix ohci1394: fw-host0: Unexpected PCI resource length of 1000!
Jan 5 08:47:14 matrix ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
Jan 5 08:47:14 matrix sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
Jan 5 08:47:14 matrix ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
Jan 5 08:47:14 matrix ieee1394: sbp2: Try serialize_io=0 for better performance
Jan 5 08:47:14 matrix ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Jan 5 08:47:14 matrix PCI: Enabling device 0001:10:18.0 (0000 -> 0002)
Jan 5 08:47:14 matrix ohci_hcd 0001:10:18.0: OHCI Host Controller
Jan 5 08:47:14 matrix ohci_hcd 0001:10:18.0: new USB bus registered, assigned bus number 1
Jan 5 08:47:14 matrix ohci_hcd 0001:10:18.0: irq 27, io mem 0x80081000
Jan 5 08:47:14 matrix hub 1-0:1.0: USB hub found
Jan 5 08:47:14 matrix hub 1-0:1.0: 2 ports detected
Jan 5 08:47:14 matrix PCI: Enabling device 0001:10:19.0 (0000 -> 0002)
Jan 5 08:47:14 matrix ohci_hcd 0001:10:19.0: OHCI Host Controller
Jan 5 08:47:14 matrix ohci_hcd 0001:10:19.0: new USB bus registered, assigned bus number 2
Jan 5 08:47:14 matrix ohci_hcd 0001:10:19.0: irq 28, io mem 0x80080000
Jan 5 08:47:14 matrix hub 2-0:1.0: USB hub found
Jan 5 08:47:14 matrix hub 2-0:1.0: 2 ports detected
Jan 5 08:47:14 matrix usbcore: registered new driver usblp
Jan 5 08:47:14 matrix drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Jan 5 08:47:14 matrix Initializing USB Mass Storage driver...
Jan 5 08:47:14 matrix usbcore: registered new driver usb-storage
Jan 5 08:47:14 matrix USB Mass Storage support registered.
Jan 5 08:47:14 matrix usbcore: registered new driver hiddev
Jan 5 08:47:14 matrix usbcore: registered new driver usbhid
Jan 5 08:47:14 matrix drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Jan 5 08:47:14 matrix i2c /dev entries driver
Jan 5 08:47:14 matrix Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Jan 5 08:47:14 matrix Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
Jan 5 08:47:14 matrix Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).
Jan 5 08:47:14 matrix ALSA device list:
Jan 5 08:47:14 matrix #0: PowerMac Tumbler (Dev 16) Sub-frame 0
Jan 5 08:47:14 matrix NET: Registered protocol family 2
Jan 5 08:47:14 matrix IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 5 08:47:14 matrix TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan 5 08:47:14 matrix TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan 5 08:47:14 matrix TCP: Hash tables configured (established 16384 bind 16384)
Jan 5 08:47:14 matrix TCP reno registered
Jan 5 08:47:14 matrix TCP bic registered
Jan 5 08:47:14 matrix NET: Registered protocol family 1
Jan 5 08:47:14 matrix NET: Registered protocol family 17
Jan 5 08:47:14 matrix ReiserFS: hda4: found reiserfs format "3.6" with standard journal
Jan 5 08:47:14 matrix ieee1394: Host added: ID:BUS[0-00:1023] GUID[000393fffe064a84]
Jan 5 08:47:14 matrix ReiserFS: hda4: using ordered data mode
Jan 5 08:47:14 matrix ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Jan 5 08:47:14 matrix ReiserFS: hda4: checking transaction log (hda4)
Jan 5 08:47:14 matrix ReiserFS: hda4: journal-1153: found in header: first_unflushed_offset 5959, last_flushed_trans_id 151742
Jan 5 08:47:14 matrix ReiserFS: hda4: journal-1206: Starting replay from offset 651734711671732, trans_id 18
Jan 5 08:47:14 matrix ReiserFS: hda4: journal-1299: Setting newest_mount_id to 121
Jan 5 08:47:14 matrix ReiserFS: hda4: Using r5 hash to sort names
Jan 5 08:47:14 matrix VFS: Mounted root (reiserfs filesystem) readonly.
Jan 5 08:47:14 matrix Freeing unused kernel memory: 220k init 4k chrp 32k prep
Jan 5 08:47:14 matrix Adding 524280k swap on /dev/hda3. Priority:-1 extents:1 across:524280k
Jan 5 08:47:18 matrix eth0: Link is up at 10 Mbps, half-duplex.
Jan 5 08:47:18 matrix eth0: Pause is disabled
Jan 5 08:47:20 matrix rpc.statd[5711]: Version 1.0.6 Starting
Jan 5 08:47:23 matrix smbd[5768]: [1904/01/05 08:47:23, 0] printing/print_cups.c:cups_cache_reload(85)
Jan 5 08:47:23 matrix smbd[5768]: Unable to connect to CUPS server localhost - Connection refused
Jan 5 08:47:23 matrix smbd[5768]: [1904/01/05 08:47:23, 0] printing/print_cups.c:cups_cache_reload(85)
Jan 5 08:47:23 matrix smbd[5768]: Unable to connect to CUPS server localhost - Connection refused
Jan 5 08:47:25 matrix NET: Registered protocol family 10
Jan 5 08:47:25 matrix IPv6 over IPv4 tunneling driver
Jan 5 08:47:25 matrix sshd[5820]: Server listening on :: port 22.
Jan 5 08:47:25 matrix sshd[5820]: error: Bind to port 22 on 0.0.0.0 failed: Address already in use.
Jan 5 08:47:25 matrix cron[5856]: (CRON) STARTUP (V5.0)
Jan 5 08:47:35 matrix login(pam_unix)[5909]: session opened for user playahater by (uid=0)
Jan 5 08:47:35 matrix eth0: no IPv6 routers present
Jan 5 08:47:39 matrix su(pam_unix)[5950]: session opened for user root by (uid=1000)
Mar 21 20:50:02 matrix su(pam_unix)[5950]: session closed for user root
Mar 21 20:50:02 matrix syslog-ng[5241]: STATS: dropped 0
Mar 21 20:50:09 matrix agpgart: Putting AGP V2 device at 0000:00:0b.0 into 2x mode
Mar 21 20:50:09 matrix agpgart: Putting AGP V2 device at 0000:00:10.0 into 2x mode
Mar 21 20:51:24 matrix su(pam_unix)[6028]: session opened for user root by (uid=1000)
Mar 21 20:51:30 matrix IN from bad port 61 at c023b57c
Mar 21 20:51:30 matrix IN from bad port 61 at c023b57c
matrix / #
|
here is the most important part of dmesg
| Code: |
matrix / # cat /var/log/messages |grep serial
Jan 5 08:47:14 matrix pmac_zilog: Error registering serial device, disabling pmac_zilog.
Jan 5 08:47:14 matrix pmac_zilog: Did another serial driver already claim the minors?
Jan 5 08:47:14 matrix ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
Jan 5 08:47:14 matrix ieee1394: sbp2: Try serialize_io=0 for better performance
matrix / #
|
maybe i need to exclude something from kernel?
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
JoseJX
Retired Dev
Joined: 28 Apr 2002
Posts: 2774
|
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Tue Mar 21, 2006 9:04 pm Post subject: |
|
|
| JoseJX wrote: | Yes, that's it, try removing these options from your kernel:
CONFIG_SERIAL_8250=y
CONFIG_SERIO_I8042=y |
OK .. chief ... .. i`ll do that ..
I`ll post results ..
10x
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Wed Mar 29, 2006 12:02 pm Post subject: |
|
|
Heh . . ..
this is got to be a kernel problem .. cuz i have been trying to compile it so everyting will work but it doesn`t .. somehow, one thing is always not working .. sometimes its alsa, sometimes pbbuttons, sometimes sleep ..
somehow i cant compile it with the same conf that i`m using now (2.6.14 gentoo-sources but without modem ) without any problems ..
and speaking of conf .. i`m not sure if i`m using conf file where everyting works except modem(current one) .. is there any way to "extract" conf from image (i think i didn`t compile that option) .. i have tried to use the ".conf" from /usr/src/linux/.conf but it seems that that`s not the right one, or it`s just not working with 2.6.15
bottom line .. i have setup serial with 2.6.15 and modem is working .. ..
i will try some other kernel or kernel version .. cuz gentoo-sources-2.6.15 are not woking completely in my case
10x for help
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
JoseJX
Retired Dev
Joined: 28 Apr 2002
Posts: 2774
|
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Fri Apr 14, 2006 3:11 pm Post subject: |
|
|
Hi guys ... after trying to fix the problem myself, i decided to ask for help ..
in last couple of weeks, i have been trying a couple of kernel versions and i always get the same result ..
bottom line is that i have managed to compile kernel which can detect all hardware without any problems ( modem is detected without any errors ) .. but only problem left is pbbutonsd ..
somehow, only with first compiled kernel (even though i am using its .conf as a start point for configuration of newer kernel versions) i have fully working keyboard (but not a serial modem ).
I can`t get volume,brightness and eject buttons to work, in combination with "fn" button, with newer kernel, therefore i don`t have sound when i boot for example 2.6.15 (newer compiled kernel) because speakers are muted and only "fn+F3" can unmute (just to mention that there are no other errors .. alsa and arts are working 100% .. )
even though i have tried to set the starting volume in pbbuttonsd.conf on 90 (so it is unmuted uppon boot) there is no sound .. ofcourse, all mixer levels in alsamixer are set to high point and umuted.
here is my newest/final .conf which, i beleve, is a fully working one of many ..
| Code: |
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.15-gentoo-r1
# Thu Apr 6 17:45:07 2006
#
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
#
# Block layer
#
CONFIG_LBD=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
#
# Processor
#
CONFIG_6xx=y
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_POWER3 is not set
# CONFIG_POWER4 is not set
# CONFIG_8xx is not set
# CONFIG_E200 is not set
# CONFIG_E500 is not set
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_TAU=y
# CONFIG_TAU_INT is not set
# CONFIG_TAU_AVERAGE is not set
# CONFIG_KEXEC is not set
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
CONFIG_CPU_FREQ_PMAC=y
CONFIG_PPC601_SYNC_FIX=y
# CONFIG_WANT_EARLY_SERIAL is not set
CONFIG_PPC_STD_MMU=y
#
# Platform options
#
CONFIG_PPC_MULTIPLATFORM=y
# CONFIG_APUS is not set
# CONFIG_KATANA is not set
# CONFIG_WILLOW is not set
# CONFIG_CPCI690 is not set
# CONFIG_POWERPMC250 is not set
# CONFIG_CHESTNUT is not set
# CONFIG_SPRUCE is not set
# CONFIG_HDPU is not set
# CONFIG_EV64260 is not set
# CONFIG_LOPEC is not set
# CONFIG_MVME5100 is not set
# CONFIG_PPLUS is not set
# CONFIG_PRPMC750 is not set
# CONFIG_PRPMC800 is not set
# CONFIG_SANDPOINT is not set
# CONFIG_RADSTONE_PPC7D is not set
# CONFIG_PAL4 is not set
# CONFIG_GEMINI is not set
# CONFIG_EST8260 is not set
# CONFIG_SBC82xx is not set
# CONFIG_SBS8260 is not set
# CONFIG_RPX8260 is not set
# CONFIG_TQM8260 is not set
# CONFIG_ADS8272 is not set
# CONFIG_PQ2FADS is not set
# CONFIG_LITE5200 is not set
# CONFIG_MPC834x_SYS is not set
# CONFIG_EV64360 is not set
CONFIG_PPC_CHRP=y
CONFIG_PPC_PMAC=y
CONFIG_PPC_PREP=y
CONFIG_PPC_OF=y
CONFIG_PPCBUG_NVRAM=y
# CONFIG_SMP is not set
# CONFIG_HIGHMEM is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_PROC_DEVICETREE=y
CONFIG_PREP_RESIDUAL=y
CONFIG_PROC_PREPRESIDUAL=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y
#
# Bus options
#
CONFIG_ISA=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PPC_I8259=y
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_LEGACY_PROC=y
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=m
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
# CONFIG_I82365 is not set
# CONFIG_TCIC is not set
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=m
#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set
#
# Default settings for advanced configuration options are used
#
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_TASK_SIZE=0x80000000
CONFIG_BOOT_LOAD=0x00800000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
#
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK is not set
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
CONFIG_IP_NF_CONNTRACK_MARK=y
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
# CONFIG_IP_NF_CT_PROTO_SCTP is not set
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
# CONFIG_IP_NF_NETBIOS_NS is not set
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
# CONFIG_IP_NF_PPTP is not set
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_REALM=m
CONFIG_IP_NF_MATCH_SCTP=m
# CONFIG_IP_NF_MATCH_DCCP is not set
CONFIG_IP_NF_MATCH_COMMENT=m
CONFIG_IP_NF_MATCH_CONNMARK=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
# CONFIG_IP_NF_MATCH_STRING is not set
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
# CONFIG_IP_NF_TARGET_NFQUEUE is not set
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
# CONFIG_IP_NF_TARGET_TTL is not set
CONFIG_IP_NF_TARGET_CONNMARK=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
# CONFIG_IP_NF_ARPFILTER is not set
# CONFIG_IP_NF_ARP_MANGLE is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
CONFIG_IEEE80211=m
CONFIG_IEEE80211_DEBUG=y
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play support
#
CONFIG_PNP=y
CONFIG_PNP_DEBUG=y
#
# Protocols
#
CONFIG_ISAPNP=y
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_MAC_FLOPPY is not set
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
CONFIG_BLK_DEV_UB=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=y
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_SL82C105 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
CONFIG_BLK_DEV_CMD64X=y
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=m
CONFIG_PDC202XX_BURST=y
CONFIG_BLK_DEV_PDC202XX_NEW=y
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_BLINK=y
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC7XXX_OLD=m
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
CONFIG_SCSI_MESH=y
CONFIG_SCSI_MESH_SYNC_RATE=5
CONFIG_SCSI_MESH_RESET_DELAY_MS=4000
CONFIG_SCSI_MAC53C94=y
#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=y
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
CONFIG_IEEE1394_OUI_DB=y
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=y
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
CONFIG_IEEE1394_AMDTP=m
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Macintosh device drivers
#
CONFIG_ADB=y
CONFIG_ADB_CUDA=y
CONFIG_ADB_PMU=y
CONFIG_PMAC_APM_EMU=y
CONFIG_PMAC_MEDIABAY=y
CONFIG_PMAC_BACKLIGHT=y
CONFIG_ADB_MACIO=y
CONFIG_INPUT_ADBHID=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_THERM_WINDTUNNEL=m
CONFIG_THERM_ADT746X=m
CONFIG_WINDFARM=m
CONFIG_ANSLCD=y
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_MACE=y
# CONFIG_MACE_AAUI_PORT is not set
CONFIG_BMAC=y
# CONFIG_HAPPYMEAL is not set
CONFIG_SUNGEM=y
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
CONFIG_DE2104X=y
CONFIG_TULIP=y
# CONFIG_TULIP_MWI is not set
CONFIG_TULIP_MMIO=y
# CONFIG_TULIP_NAPI is not set
CONFIG_DE4X5=m
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_PCMCIA_XIRCOM is not set
# CONFIG_PCMCIA_XIRTULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
# CONFIG_NET_PCI is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_MV643XX_ETH is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set
# CONFIG_ARLAN is not set
# CONFIG_WAVELAN is not set
# CONFIG_PCMCIA_WAVELAN is not set
# CONFIG_PCMCIA_NETWAVE is not set
#
# Wireless 802.11 Frequency Hopping cards support
#
# CONFIG_PCMCIA_RAYCS is not set
#
# Wireless 802.11b ISA/PCI cards support
#
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_AIRO is not set
CONFIG_HERMES=m
CONFIG_APPLE_AIRPORT=m
# CONFIG_PLX_HERMES is not set
# CONFIG_TMD_HERMES is not set
# CONFIG_NORTEL_HERMES is not set
# CONFIG_PCI_HERMES is not set
# CONFIG_ATMEL is not set
#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
# CONFIG_PCMCIA_HERMES is not set
# CONFIG_PCMCIA_SPECTRUM is not set
# CONFIG_AIRO_CS is not set
# CONFIG_PCMCIA_WL3501 is not set
#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_PRISM54 is not set
# CONFIG_HOSTAP is not set
CONFIG_NET_WIRELESS=y
#
# PCMCIA network device support
#
# CONFIG_NET_PCMCIA is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=y
CONFIG_PPP_SYNC_TTY=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
# CONFIG_PPP_MPPE is not set
CONFIG_PPPOE=y
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_EVBUG=m
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
CONFIG_INPUT_UINPUT=m
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_PMACZILOG=y
CONFIG_SERIAL_PMACZILOG_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_NVRAM=y
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
CONFIG_AGP_UNINORTH=y
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
CONFIG_DRM_R128=y
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_CARDMAN_4000 is not set
# CONFIG_CARDMAN_4040 is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_ALGOPCF=y
CONFIG_I2C_ALGOPCA=y
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_ELEKTOR is not set
CONFIG_I2C_HYDRA=y
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_KEYWEST=y
# CONFIG_I2C_MPC is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_SENSORS_M41T00 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_RTC_X1205_I2C is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
# CONFIG_HWMON_VID is not set
#
# Misc devices
#
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_MACMODES=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_OF=y
CONFIG_FB_CONTROL=y
CONFIG_FB_PLATINUM=y
CONFIG_FB_VALKYRIE=y
# CONFIG_FB_CT65550 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
CONFIG_FB_ATY128=y
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
CONFIG_FB_VIRTUAL=y
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_FONT_6x11=y
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_DEVICE=y
#
# Speakup console speech
#
# CONFIG_SPEAKUP is not set
CONFIG_SPEAKUP_DEFAULT="none"
#
# Sound
#
CONFIG_SOUND=y
# CONFIG_DMASOUND_PMAC is not set
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_GENERIC_DRIVER=y
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# ISA devices
#
CONFIG_SND_CS4231_LIB=m
# CONFIG_SND_AD1816A is not set
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_CS4231 is not set
CONFIG_SND_CS4232=m
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_ES968 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_ALS100 is not set
# CONFIG_SND_AZT2320 is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_DT019X is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_HDA_INTEL is not set
#
# ALSA PowerMac devices
#
CONFIG_SND_POWERMAC=y
CONFIG_SND_POWERMAC_AUTO_DRC=y
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_ITMTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
CONFIG_USB_PEGASUS=m
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_AIRPRIME is not set
# CONFIG_USB_SERIAL_ANYDATA is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP2101 is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
CONFIG_USB_SERIAL_VISOR=m
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OPTION is not set
# CONFIG_USB_SERIAL_OMNINET is not set
CONFIG_USB_EZUSB=y
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=m
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=m
CONFIG_REISERFS_FS=y
CONFIG_REISERFS_CHECK=y
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_EXPORT=y
# CONFIG_XFS_QUOTA is not set
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=y
CONFIG_HFSPLUS_FS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=y
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=y
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
# CONFIG_NFSD_V4 is not set
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-15"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
CONFIG_NLS_CODEPAGE_863=m
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
#
# Library routines
#
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_XMON is not set
# CONFIG_BDI_SWITCH is not set
CONFIG_BOOTX_TEXT=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
CONFIG_CRYPTO_AES=m
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
CONFIG_CRYPTO_ARC4=m
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_DEFLATE is not set
CONFIG_CRYPTO_MICHAEL_MIC=m
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
|
10x in advance
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
mabhobs
Tux's lil' helper
Joined: 10 Feb 2006
Posts: 83
|
| Posted: Mon Jun 05, 2006 11:31 am Post subject: |
|
|
I tried to get this modem working too. I have the same ibook but haven't really found out if my ibook has a soft or hardware modem. It seems this model just experienced the transition from hardware to soft modem. Is there a systematical way to determine if we have a software or hardware modem?
Sorry playahater I haven't found a solution yet, but I am still looking for one. I will keep you posted for updates. |
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Mon Jun 05, 2006 9:21 pm Post subject: |
|
|
| mabhobs wrote: | I tried to get this modem working too. I have the same ibook but haven't really found out if my ibook has a soft or hardware modem. It seems this model just experienced the transition from hardware to soft modem. Is there a systematical way to determine if we have a software or hardware modem?
Sorry playahater I haven't found a solution yet, but I am still looking for one. I will keep you posted for updates. |
Hey mabhobs,
i have solved the problem .. .. all I had to do was to compile the kernel with pmac_zilog support and to completely leave out the serial devices support ..
Try that .. if you have the same modem as I do, that has got to be a solution ..
concerning brightness, volume and eject .. they suddenly start working .. ..
and last week i bought airport (not extreme) and managed to set it up too ..
so .. if you need any problems .. post .. .. i`ll try to help ..
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
mabhobs
Tux's lil' helper
Joined: 10 Feb 2006
Posts: 83
|
| Posted: Mon Jun 12, 2006 2:46 pm Post subject: |
|
|
Thanks for your response. I just compiled my kernel with the pmac_zilog driver and I get the following dmesg autput. I do not have the option to test my modem at the moment, becaue I am traveling, but I was wondering if you could tell me if you have the same dmesg output so I know if I also have the hardware modem. This is what the my dmesg said:
| Code: | pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port |
I would really appreciate your help. |
|
| Back to top |
|
|
playahater
Guru
Joined: 02 Jul 2005
Posts: 382
Location: Serbia
|
| Posted: Mon Jun 12, 2006 7:26 pm Post subject: |
|
|
| mabhobs wrote: | Thanks for your response. I just compiled my kernel with the pmac_zilog driver and I get the following dmesg autput. I do not have the option to test my modem at the moment, becaue I am traveling, but I was wondering if you could tell me if you have the same dmesg output so I know if I also have the hardware modem. This is what the my dmesg said:
| Code: | pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port |
I would really appreciate your help. |
well .. .. almost ..
| Code: |
[ 22.357098] pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
[ 22.357402] ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Internal modem
[ 22.358530] ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port
|
hmmm .. are you sure u have the same ibook as I ? ..
for start .. can u post your .. lspci -vv .. and .. did you completely remove other serial devices from kernel ?
Cheers
_________________
http://droopia.net |
|
| Back to top |
|
|
mabhobs
Tux's lil' helper
Joined: 10 Feb 2006
Posts: 83
|
| Posted: Thu Jul 13, 2006 9:21 pm Post subject: |
|
|
lspci --v shows this:
| Code: | 00:0b.0 Host bridge: Apple Computer Inc. UniNorth/Pangea AGP
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 16, Cache Line Size 08
Capabilities: [80] AGP version 1.0
Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
00:10.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev 02) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Mobility M3 AGP 2x
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 255 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 48
Region 0: Memory at 94000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at f0000400 [size=256]
Region 2: Memory at 90000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at f1000000 [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=8 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0001:10:0b.0 Host bridge: Apple Computer Inc. UniNorth/Pangea PCI
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 16, Cache Line Size 08
0001:10:17.0 Class ff00: Apple Computer Inc. KeyLargo/Pangea Mac I/O
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size 08
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
0001:10:18.0 USB Controller: Apple Computer Inc. KeyLargo/Pangea USB (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (750ns min, 21500ns max)
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 80081000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
0001:10:19.0 USB Controller: Apple Computer Inc. KeyLargo/Pangea USB (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (750ns min, 21500ns max)
Interrupt: pin A routed to IRQ 28
Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
0002:20:0b.0 Host bridge: Apple Computer Inc. UniNorth/Pangea Internal PCI
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 16, Cache Line Size 08
0002:20:0e.0 Class ffff: Illegal Vendor ID Unknown device ffff (rev ff) (prog-if ff)
!!! Unknown header type 7f
0002:20:0f.0 Ethernet controller: Apple Computer Inc. UniNorth/Pangea GMAC (Sun GEM)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 16 (16000ns min, 16000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f5200000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at f5100000 [disabled] [size=1M] |
Does yours look the same? |
|
| Back to top |
|
|
makaveli87
Guru
Joined: 22 Aug 2005
Posts: 311
Location: Italy
|
| Posted: Mon Jul 31, 2006 11:21 am Post subject: |
|
|
I've a powermac Cube...
After reading this discussion I activated the built-in support to
<*> PowerMac z85c30 ESCC support (CONFIG_SERIAL_PMACZILOG)
Now this is dmesg:
| Code: |
pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
pmac_zilog: i2c-modem detected, id: 1
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Internal modem
ttyS1 at MMIO 0x80013000 (irq = 50) is a Z85c30 ESCC - Serial port
|
but..I've never used a 56 kbps modem on linux... what can I do to test the modem?
_________________
GoogleTalk: romanovic@gmail.com |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Gentoo on PPC
