| View previous topic :: View next topic |
| Author |
Message |
MackDSM
n00b
Joined: 27 Apr 2006
Posts: 2
Location: Ontario, Canada
|
 Posted: Thu Apr 27, 2006 7:32 pm Post subject: Basic Wireless (Madwifi) Issues |
 |
|
Hello all,
As a quick background, I am very new to Linux in general. I had installed a few distro's in the past, but only ever used them for a few days before my will broke and I converted back to Windows. I was thinking about trying Linux again, and at the advice of a friend, went with the Gentoo distribution. Rather than using an install CD, I did everything manually in an attempt to learn more and gain a better overall understanding of how Linux works. I basically followed the Gentoo Handbook all the way through, and now have KDE running well. However, I am having issues getting my wireless networking to work.
After doing some searching and research, I learned that because my Toshiba laptop has an Atheros brand wireless card built into it, I would have to use the Madwifi drivers to be able to get it to work properly. I emerge'd madwifi-ng and madwifi-tools, as well as wireless-tools. Following the instructions at madwifi.org, after the emerge was finished, I attempted to run modprobe ath_pci. This returned the following;
| Quote: | WARNING: Error inserting wlan (/lib/modules/2.6.16-gentoo-r3/net/wlan.ko): Unknown symbol in module, or unknown parameter (see dmesg)
WARNING: Error inserting ath_rate_sample (/lib/modules/2.6.16-gentoo-r3/net/ath_rate_sample.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error inserting ath_pci (/lib/modules/2.6.16-gentoo-r3/net/ath_pci.ko): Unknown symbol in module, or unknown parameter (see dmesg) |
I ran a few searches on these forums and found a few posts where people were having the same issue. Some of the suggestions were to ensure that Wireless LAN support was enabled in the kernel. It was not, so I enabled this and recompiled. After doing this, I re-emerge'd madwifi-ng and madwifi-tools and attempted the modprobe again but was greeted with the same error. I should note, however, that while re-compiling the kernel I received some errors at the end stating;
| Quote: | WARNING: /lib/modules/2.6.12-gentoo-r6/net/ath_pci.ko needs unknown symbol ieee80211_ioctl
WARNING: /lib/modules/2.6.12-gentoo-r6/net/wlan_ccmp.ko needs unknown symbol crypto_alloc_tfm
WARNING: /lib/modules/2.6.12-gentoo-r6/net/wlan_ccmp.ko needs unknown symbol crypto_free_tfm |
I found another post with this exact error which suggested trying;
| Quote: | cd /lib/modules/2.6.12-gentoo-r6/net
rm *
emerge madwifi-driver |
I did this as well, but still received the same error when trying to do the modprobe. Being a very new user to Linux, I am fairly lost at this point. I understand everything that I've been doing, but do not know what to turn to now. If anyone could provide me with any help or insight it would be greatly appreciated. Also, for reference I have added the results of running lspci and dmesg below. Thank you very much.
| Quote: | lspci results:
00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation NV31M [GeForce FX Go5600] (rev a1)
02:06.0 USB Controller: NEC Corporation USB (rev 41)
02:06.1 USB Controller: NEC Corporation USB (rev 41)
02:06.2 USB Controller: NEC Corporation USB 2.0 (rev 02)
02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
02:0a.0 Ethernet controller: Atheros Communications, Inc. AR5211 802.11ab NIC (rev 01)
02:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 33)
02:0d.0 System peripheral: Toshiba America Info Systems SD TypA Controller (rev 05)
|
| Quote: | dmesg results:
Linux version 2.6.16-gentoo-r3 (root@livecd) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7. ) #3 SMP PREEMPT Sun Apr 23 11:54:14 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffcc000 (usable)
BIOS-e820: 000000001ffcc000 - 000000001ffd0000 (reserved)
BIOS-e820: 000000001ffd0000 - 000000001ffe0000 (ACPI data)
BIOS-e820: 000000001ffe0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131020
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 126924 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f0180
ACPI: RSDT (v001 TOSHIB 5200 0x20030327 TASM 0x04010000) @ 0x1ffd0000
ACPI: FADT (v002 TOSHIB 5200 0x20021230 TASM 0x04010000) @ 0x1ffd0058
ACPI: DBGP (v001 TOSHIB 5200 0x20030327 TASM 0x04010000) @ 0x1ffd00dc
ACPI: BOOT (v001 TOSHIB 5200 0x20030327 TASM 0x04010000) @ 0x1ffd0030
ACPI: DSDT (v001 TOSHIB 5200 0x20030327 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0xd808
Allocating PCI resources starting at 30000000 (gap: 20000000:deda0000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 video=vesafb:mtrr:3,ywrap,1280x1024-32@60
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01443000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2194.910 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514024k/524080k available (2993k kernel code, 9552k reserved, 933k data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4397.56 BogoMIPS (lpj=8795126)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0af8)
CPU0: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.20GHz stepping 07
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfcf0c, last bus=4
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 6 7 10 11 12)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region d800-d87f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region eec0-eeff claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 23
PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fd000000-fdffffff
PREFETCH window: d0000000-dfffffff
PCI: Bus 3, cardbus bridge: 0000:02:0b.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 30000000-31ffffff
MEM window: 34000000-35ffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: fce00000-fcefffff
PREFETCH window: 30000000-31ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Simple Boot Flag at 0x7c set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1146150281.700:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
lp: driver loaded but no devices found
Toshiba System Managment Mode driver v1.11 26/9/2001
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i845 Chipset.
agpgart: AGP aperture is 256M @ 0xe0000000
[drm] Initialized drm 1.0.1 20051102
vesafb: NVIDIA Corporation, NV31 Board - tsm31enz, Chip Rev (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:e140
vesafb: pmi: set display start = c00ce176, set palette = c00ce1e0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: VBIOS/hardware doesn't support DDC transfers
vesafb: no monitor limits have been set
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=2048
vesafb: framebuffer at 0xd0000000, mapped to 0xe0900000, using 10240k, total 65536k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (74 C)
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALD.GHCI
PNP: PS/2 Controller [PNP0303:KBC] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
floppy0: no floppy controllers found
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKE] -> GSI 4 (level, low) -> IRQ 4
e100: eth0: e100_probe: addr 0xfcefd000, irq 4, MAC addr 00:08:0D:44:56:50
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK6021GAS, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-R6012, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
PCI: Enabling device 0000:02:07.0 (0000 -> 0002)
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKF] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:02:07.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[fce05000-fce057ff] Max Packet=[2048] IR/IT contexts=[4/8]
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
PCI: Enabling device 0000:02:06.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:06.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:02:06.2: EHCI Host Controller
ehci_hcd 0000:02:06.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:06.2: irq 11, io mem 0xfce05a00
ehci_hcd 0000:02:06.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
PCI: setting IRQ 6 as level-triggered
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
ohci_hcd 0000:02:06.0: OHCI Host Controller
ohci_hcd 0000:02:06.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:02:06.0: irq 6, io mem 0xfceff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:02:06.1[B] -> Link [LNKE] -> GSI 4 (level, low) -> IRQ 4
ohci_hcd 0000:02:06.1: OHCI Host Controller
ohci_hcd 0000:02:06.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:06.1: irq 4, io mem 0xfcefe000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 2-3: new full speed USB device using ohci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000039000038bc07]
usb 2-3: configuration #1 chosen from 1 choice
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:02:06.0-1
input: Synaptics Inc. Synaptics cPad as /class/input/input3
input: USB HID v1.00 Mouse [Synaptics Inc. Synaptics cPad] on usb-0000:02:06.0-3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
PCI: Enabling device 0000:00:1f.5 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55390 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel 82801CA-ICH3 with YMF753 at 0x1000, irq 10
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 393216 bytes)
TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 220k freed
kjournald starting. Commit interval 5 seconds
Adding 2008116k swap on /dev/hda2. Priority:-1 extents:1 across:2008116k
EXT3 FS on hda3, internal journal
usbcore: registered new driver touchkitusb
usbcore: registered new driver cytherm
drivers/usb/misc/cytherm.c: v1.0:Cypress USB Thermometer driver
usbcore: registered new driver phidgetservo
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKG] -> GSI 5 (level, low) -> IRQ 5
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8756 Wed Mar 29 14:26:26 PST 2006
NVRM: PAT index 1 already configured for Write-Combining!
NVRM: Aborting, due to PAT already being configured
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: Unknown symbol wireless_send_event
ath_rate_sample: Unknown symbol ether_sprintf
ath_rate_sample: Unknown symbol ieee80211_iterate_nodes
ath_pci: Unknown symbol ath_rate_tx_complete
ath_pci: Unknown symbol ieee80211_encap
ath_pci: Unknown symbol ieee80211_input
ath_pci: Unknown symbol ieee80211_ifattach
ath_pci: Unknown symbol ieee80211_beacon_update
ath_pci: Unknown symbol ieee80211_find_channel
ath_pci: Unknown symbol ieee80211_find_rxnode
ath_pci: Unknown symbol ath_rate_attach
ath_pci: Unknown symbol ether_sprintf
ath_pci: Unknown symbol ieee80211_vap_setup
ath_pci: Unknown symbol ieee80211_ifdetach
ath_pci: Unknown symbol ieee80211_free_node
ath_pci: Unknown symbol ieee80211_input_monitor
ath_pci: Unknown symbol ath_rate_newassoc
ath_pci: Unknown symbol ieee80211_crypto_newkey
ath_pci: Unknown symbol ieee80211_crypto_setkey
ath_pci: Unknown symbol ieee80211_dump_pkt
ath_pci: Unknown symbol ieee80211_ioctl_create_vap
ath_pci: Unknown symbol ieee80211_dfs_test_return
ath_pci: Unknown symbol ieee80211_stop_running
ath_pci: Unknown symbol ieee80211_cipher_none
ath_pci: Unknown symbol ieee80211_crypto_delkey
ath_pci: Unknown symbol ieee80211_media_change
ath_pci: Unknown symbol ieee80211_beacon_miss
ath_pci: Unknown symbol ieee80211_beacon_alloc
ath_pci: Unknown symbol ieee80211_getcfframe
ath_pci: Unknown symbol ieee80211_vap_attach
ath_pci: Unknown symbol ieee80211_ibss_merge
ath_pci: Unknown symbol ath_rate_node_cleanup
ath_pci: Unknown symbol ieee80211_send_qosnulldata
ath_pci: Unknown symbol ath_rate_detach
ath_pci: Unknown symbol ieee80211_create_vap
ath_pci: Unknown symbol ieee80211_wme_acnames
ath_pci: Unknown symbol ieee80211_input_all
ath_pci: Unknown symbol ieee80211_media_status
ath_pci: Unknown symbol ieee80211_start_running
ath_pci: Unknown symbol ieee80211_vap_detach
ath_pci: Unknown symbol ieee80211_announce
ath_pci: Unknown symbol ieee80211_mark_dfs
ath_pci: Unknown symbol ieee80211_chan2ieee
ath_pci: Unknown symbol ieee80211_state_name
ath_pci: Unknown symbol ath_rate_node_init
ath_pci: Unknown symbol ath_rate_findrate
ath_pci: Unknown symbol ieee80211_dturbo_switch
ath_pci: Unknown symbol ieee80211_crypto_encap
ath_pci: Unknown symbol ieee80211_chan2mode
ath_pci: Unknown symbol ieee80211_getrssi
ath_pci: Unknown symbol ieee80211_find_txnode
ath_pci: Unknown symbol ath_rate_newstate
ath_pci: Unknown symbol ath_rate_setupxtxdesc
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
wlan: Unknown symbol wireless_send_event
ath_rate_sample: Unknown symbol ether_sprintf
ath_rate_sample: Unknown symbol ieee80211_iterate_nodes
ath_pci: Unknown symbol ath_rate_tx_complete
ath_pci: Unknown symbol ieee80211_encap
ath_pci: Unknown symbol ieee80211_input
ath_pci: Unknown symbol ieee80211_ifattach
ath_pci: Unknown symbol ieee80211_beacon_update
ath_pci: Unknown symbol ieee80211_find_channel
ath_pci: Unknown symbol ieee80211_find_rxnode
ath_pci: Unknown symbol ath_rate_attach
ath_pci: Unknown symbol ether_sprintf
ath_pci: Unknown symbol ieee80211_vap_setup
ath_pci: Unknown symbol ieee80211_ifdetach
ath_pci: Unknown symbol ieee80211_free_node
ath_pci: Unknown symbol ieee80211_input_monitor
ath_pci: Unknown symbol ath_rate_newassoc
ath_pci: Unknown symbol ieee80211_crypto_newkey
ath_pci: Unknown symbol ieee80211_crypto_setkey
ath_pci: Unknown symbol ieee80211_dump_pkt
ath_pci: Unknown symbol ieee80211_ioctl_create_vap
ath_pci: Unknown symbol ieee80211_dfs_test_return
ath_pci: Unknown symbol ieee80211_stop_running
ath_pci: Unknown symbol ieee80211_cipher_none
ath_pci: Unknown symbol ieee80211_crypto_delkey
ath_pci: Unknown symbol ieee80211_media_change
ath_pci: Unknown symbol ieee80211_beacon_miss
ath_pci: Unknown symbol ieee80211_beacon_alloc
ath_pci: Unknown symbol ieee80211_getcfframe
ath_pci: Unknown symbol ieee80211_vap_attach
ath_pci: Unknown symbol ieee80211_ibss_merge
ath_pci: Unknown symbol ath_rate_node_cleanup
ath_pci: Unknown symbol ieee80211_send_qosnulldata
ath_pci: Unknown symbol ath_rate_detach
ath_pci: Unknown symbol ieee80211_create_vap
ath_pci: Unknown symbol ieee80211_wme_acnames
ath_pci: Unknown symbol ieee80211_input_all
ath_pci: Unknown symbol ieee80211_media_status
ath_pci: Unknown symbol ieee80211_start_running
ath_pci: Unknown symbol ieee80211_vap_detach
ath_pci: Unknown symbol ieee80211_announce
ath_pci: Unknown symbol ieee80211_mark_dfs
ath_pci: Unknown symbol ieee80211_chan2ieee
ath_pci: Unknown symbol ieee80211_state_name
ath_pci: Unknown symbol ath_rate_node_init
ath_pci: Unknown symbol ath_rate_findrate
ath_pci: Unknown symbol ieee80211_dturbo_switch
ath_pci: Unknown symbol ieee80211_crypto_encap
ath_pci: Unknown symbol ieee80211_chan2mode
ath_pci: Unknown symbol ieee80211_getrssi
ath_pci: Unknown symbol ieee80211_find_txnode
ath_pci: Unknown symbol ath_rate_newstate
ath_pci: Unknown symbol ath_rate_setupxtxdesc
wlan: Unknown symbol wireless_send_event
ath_rate_sample: Unknown symbol ether_sprintf
ath_rate_sample: Unknown symbol ieee80211_iterate_nodes
ath_pci: Unknown symbol ath_rate_tx_complete
ath_pci: Unknown symbol ieee80211_encap
ath_pci: Unknown symbol ieee80211_input
ath_pci: Unknown symbol ieee80211_ifattach
ath_pci: Unknown symbol ieee80211_beacon_update
ath_pci: Unknown symbol ieee80211_find_channel
ath_pci: Unknown symbol ieee80211_find_rxnode
ath_pci: Unknown symbol ath_rate_attach
ath_pci: Unknown symbol ether_sprintf
ath_pci: Unknown symbol ieee80211_vap_setup
ath_pci: Unknown symbol ieee80211_ifdetach
ath_pci: Unknown symbol ieee80211_free_node
ath_pci: Unknown symbol ieee80211_input_monitor
ath_pci: Unknown symbol ath_rate_newassoc
ath_pci: Unknown symbol ieee80211_crypto_newkey
ath_pci: Unknown symbol ieee80211_crypto_setkey
ath_pci: Unknown symbol ieee80211_dump_pkt
ath_pci: Unknown symbol ieee80211_ioctl_create_vap
ath_pci: Unknown symbol ieee80211_dfs_test_return
ath_pci: Unknown symbol ieee80211_stop_running
ath_pci: Unknown symbol ieee80211_cipher_none
ath_pci: Unknown symbol ieee80211_crypto_delkey
ath_pci: Unknown symbol ieee80211_media_change
ath_pci: Unknown symbol ieee80211_beacon_miss
ath_pci: Unknown symbol ieee80211_beacon_alloc
ath_pci: Unknown symbol ieee80211_getcfframe
ath_pci: Unknown symbol ieee80211_vap_attach
ath_pci: Unknown symbol ieee80211_ibss_merge
ath_pci: Unknown symbol ath_rate_node_cleanup
ath_pci: Unknown symbol ieee80211_send_qosnulldata
ath_pci: Unknown symbol ath_rate_detach
ath_pci: Unknown symbol ieee80211_create_vap
ath_pci: Unknown symbol ieee80211_wme_acnames
ath_pci: Unknown symbol ieee80211_input_all
ath_pci: Unknown symbol ieee80211_media_status
ath_pci: Unknown symbol ieee80211_start_running
ath_pci: Unknown symbol ieee80211_vap_detach
ath_pci: Unknown symbol ieee80211_announce
ath_pci: Unknown symbol ieee80211_mark_dfs
ath_pci: Unknown symbol ieee80211_chan2ieee
ath_pci: Unknown symbol ieee80211_state_name
ath_pci: Unknown symbol ath_rate_node_init
ath_pci: Unknown symbol ath_rate_findrate
ath_pci: Unknown symbol ieee80211_dturbo_switch
ath_pci: Unknown symbol ieee80211_crypto_encap
ath_pci: Unknown symbol ieee80211_chan2mode
ath_pci: Unknown symbol ieee80211_getrssi
ath_pci: Unknown symbol ieee80211_find_txnode
ath_pci: Unknown symbol ath_rate_newstate
ath_pci: Unknown symbol ath_rate_setupxtxdesc
|
|
|
| Back to top |
|
 |
swooshOnLn
l33t
Joined: 28 Feb 2006
Posts: 741
Location: Charlotte, North Carolina
|
| Posted: Thu Apr 27, 2006 9:09 pm Post subject: |
|
|
do you have the necessary wireless options enabled in your kernel?
_________________
"WARNING: you may LOL"
This is my font size, color, and signature. It will change to whatever I pick. How cool is that?
|
|
| Back to top |
|
|
MackDSM
n00b
Joined: 27 Apr 2006
Posts: 2
Location: Ontario, Canada
|
| Posted: Thu Apr 27, 2006 9:28 pm Post subject: |
|
|
| From what I understand, because my particular card isn't directly supported by the kernel all I should have to enable is Wireless LAN support with none of the particular options under it selected. If this is the case, then yes, it is enabled in the kernel. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
