| View previous topic :: View next topic |
| Author |
Message |
tesaklebestift
n00b
Joined: 17 Apr 2006
Posts: 7
|
 Posted: Wed May 17, 2006 8:07 pm Post subject: Wireless Card not detected by gentoo |
 |
|
Hi everybody,
my problem isn't to find a driver for my wireless card (orinoco should be supported), my card is not detected by gentoo. Windows XP detect and use this card, so I think the card must be ok.
wireless card: dell truemobile 1150 minipci (orinoco chipset)
dmesg
| Code: |
MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 30000000 (gap: 20000000:deda0000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=gentoo ro root=306 video=vesafb:mtrr,ywrap,1400x1050-16@60
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1196.300 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514488k/524168k available (2833k kernel code, 9208k reserved, 1132k data, 140k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2395.73 BogoMIPS (lpj=4791465)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Mobile Intel(R) Pentium(R) III CPU - M 1200MHz stepping 04
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbfee, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: Power Resource [PADA] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:02: ioport range 0x800-0x805 could not be reserved
pnp: 00:02: ioport range 0x808-0x80f could not be reserved
pnp: 00:03: ioport range 0x806-0x807 has been reserved
pnp: 00:03: ioport range 0x810-0x85f could not be reserved
pnp: 00:03: ioport range 0x860-0x87f has been reserved
pnp: 00:03: ioport range 0x880-0x8bf has been reserved
pnp: 00:03: ioport range 0x8c0-0x8df has been reserved
pnp: 00:03: ioport range 0x8e0-0x8ff has been reserved
pnp: 00:04: ioport range 0xf000-0xf0fe has been reserved
pnp: 00:04: ioport range 0xf100-0xf1fe has been reserved
pnp: 00:04: ioport range 0xf200-0xf2fe has been reserved
pnp: 00:04: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:04: ioport range 0xf500-0xf5fe has been reserved
pnp: 00:04: ioport range 0xf600-0xf6fe has been reserved
pnp: 00:04: ioport range 0xf800-0xf8fe has been reserved
pnp: 00:04: ioport range 0xf900-0xf9fe has been reserved
pnp: 00:09: ioport range 0x900-0x91f has been reserved
pnp: 00:09: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:0d: ioport range 0xbf40-0xbf5f has been reserved
pnp: 00:0d: ioport range 0xbf20-0xbf3f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: fc000000-fdffffff
PREFETCH window: e0000000-e7ffffff
PCI: Bus 3, cardbus bridge: 0000:02:01.0
IO window: 0000e000-0000e0ff
IO window: 0000e400-0000e4ff
PREFETCH window: 30000000-31ffffff
MEM window: f4000000-f5ffffff
PCI: Bus 7, cardbus bridge: 0000:02:01.1
IO window: 0000e800-0000e8ff
IO window: 00001000-000010ff
PREFETCH window: 32000000-33ffffff
MEM window: f6000000-f7ffffff
PCI: Bus 11, cardbus bridge: 0000:02:03.0
IO window: 00001400-000014ff
IO window: 00001800-000018ff
PREFETCH window: 34000000-35ffffff
MEM window: fa000000-fbffffff
PCI: Bridge: 0000:00:1e.0
IO window: e000-ffff
MEM window: f4000000-fbffffff
PREFETCH window: 30000000-36ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Enabling device 0000:02:01.1 (0000 -> 0003)
ACPI: PCI Interrupt 0000:02:01.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
Machine check exception polling timer started.
cpufreq: change failed with new_state 1 and result 0
audit: initializing netlink socket (disabled)
audit(1147890333.252:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.26 [Flags: R/O].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
hw_random: RNG not detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 830M Chipset.
agpgart: AGP aperture is 256M @ 0xd0000000
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=60) Memory=166.00 Mhz, System=166.00 MHz
radeonfb: PLL min 12000 max 35000
Non-DDC laptop panel detected
radeonfb: Monitor 1 type LCD found
radeonfb: Monitor 2 type no found
radeonfb: panel ID string: Samsung LTN150P1-L02
radeonfb: detected LVDS panel size from BIOS: 1400x1050
radeondb: BIOS provided dividers will be used
radeonfb: Dynamic Clock Power Management enabled
radeonfb (0000:01:00.0): ATI Radeon LY
kobject_register failed for radeonfb (-17)
[<c01ea123>] kobject_register+0x35/0x49
[<c0261944>] bus_add_driver+0x3e/0x84
[<c02622c2>] driver_register+0x75/0x7a
[<c01f1a8c>] pci_create_newid_file+0x1a/0x21
[<c01f1e1b>] __pci_register_driver+0x60/0x71
[<c04ee759>] radeonfb_old_init+0x39/0x41
[<c04e2646>] do_initcalls+0x4b/0x90
[<c0100283>] init+0x0/0x121
[<c01002b5>] init+0x32/0x121
[<c01012d1>] kernel_thread_helper+0x5/0xb
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THM] (50 C)
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM chipsets
intelfb: Version 0.9.2
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
mice: PS/2 mouse device common for all mice
Floppy drive(s): fd0 is 1.44M
input: AT Translated Set 2 keyboard as /class/input/input0
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:00.0: 3Com PCI 3c905C Tornado at e080ec00. Vers LK1.1.19
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, 1.1.3
ipw2100: Copyright(c) 2003-2005 Intel Corporation
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.0.8
ipw2200: Copyright(c) 2003-2005 Intel Corporation
STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
orinoco 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_plx 0.15rc3 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au>, Daniel Barlow <dan@telent.net>)
orinoco_pci 0.15rc3 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au> & Jean Tourrilhes <jt@hpl.hp.com>)
orinoco_tmd 0.15rc3 (Joerg Dorchain <joerg@dorchain.net>)
orinoco_nortel 0.15rc3 (Tobias Hoffmann & Christoph Jungegger <disdos@traum404.de>)
spectrum_cs 0.15rc3 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au>, et al)
airo: Probing for PCI adapters
airo: Finished probing for PCI adapters
Loaded prism54 driver, version 1.2
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N020ATCS04-0, ATA DISK drive
Synaptics Touchpad, model: 1, fw: 5.7, id: 0x9b48b1, caps: 0x804793/0x0
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STCD-RW/DVD-ROM GCC-4240N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:01.0 [1028:00e3]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:01.0, mfunc 0x01261222, devctl 0x64
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x36ffffff
ACPI: PCI Interrupt 0000:02:01.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:01.1 [1028:00e3]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:01.1, mfunc 0x01261222, devctl 0x64
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x36ffffff
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
Yenta: CardBus bridge found at 0000:02:03.0 [12a3:ab01]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:03.0, mfunc 0x01000002, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 7
Socket status: 30000010
pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x36ffffff
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.5 to 64
pccard: PCMCIA card inserted into slot 2
cs: memory probe 0x30000000-0x36ffffff: excluding 0x30000000-0x36ffffff
cs: memory probe 0xf4000000-0xfbffffff: excluding 0xf4000000-0xf8ffffff 0xfa000000-0xfbffffff
pcmcia: registering new device pcmcia2.0
intel8x0_measure_ac97_clock: measured 55479 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel 82801CA-ICH3 with CS4205 at 0xd800, irq 7
oprofile: using timer interrupt.
NET: Registered protocol family 2
eth1: Hardware identity 0005:0004:0005:0000
eth1: Station identity 001f:0001:0008:000a
eth1: Firmware determined as Lucent/Agere 8.10
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:7F:BE:DE
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 7, io 0xe100-0xe13f
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
Using IPI Shortcut mode
ACPI wakeup devices:
LID PBTN PCI0 USB0 USB1 USB2 MODM PCIE MPCI
ACPI: (supports S0 S1 S3 S4 S5)
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 140k freed
kjournald starting. Commit interval 5 seconds
IBM TrackPoint firmware: 0x0b, buttons: 2/3
input: TPPS/2 IBM TrackPoint as /class/input/input2
Adding 755012k swap on /dev/hda5. Priority:-1 extents:1 across:755012k
EXT3 FS on hda6, internal journal
NTFS volume version 3.1.
NTFS volume version 3.1.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
|
lspci
| Code: |
00:00.0 Host bridge: Intel Corporation 82830 830 Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corporation 82830 830 Chipset AGP Bridge (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1) (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY
02:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
02:01.0 CardBus bridge: Texas Instruments PCI1420
02:01.1 CardBus bridge: Texas Instruments PCI1420
02:03.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
|
even if I integrate drivers for the pcmcia and cardbus the wireless card won't be detected. Other cards in the PCMCIA have been detected without any problems.
Is there any body who understand this? I mean, gentoo should detect the card even if there is no driver for it. |
|
| Back to top |
|
 |
tesaklebestift
n00b
Joined: 17 Apr 2006
Posts: 7
|
| Posted: Thu May 18, 2006 4:30 pm Post subject: |
|
|
ok, problem solved.
the following modules have to be in the kernel (make menuconfig)
Bus Options --> PCCARD (PCMCIA/Cardbus) support
Load 16-Bit PCMCIA support
Cardbus yenta-compatible bridge support (automatically enables 32-Bit support)
Device drivers-->Network device support --> wireless lan (non-hamradio)
Hermes PCMCIA card support (only available if 16 Bit PCMCIA support is enabled)
Hermes chipset support 802.11b (Orinoco/Prism2/Symbol)
device drivers --> PCMCIA network device support
PCMCIA network device support |
|
| Back to top |
|
|
jeanfrancis
Veteran
Joined: 17 Dec 2005
Posts: 1482
Location: Québec, Canada
|
| Posted: Tue Jun 13, 2006 10:40 pm Post subject: |
|
|
Hi there !
I have an Oricono/PRISM2 based card and I'm unable to get it working...
That's a Mini-PCI card, do you think I need the PCMCIA things working?
I have the same things of you in my kernel but nothing seems to work.... 
What modules did you modprobe?
Thanks  |
|
| Back to top |
|
|
widan
Veteran
Joined: 07 Jun 2005
Posts: 1512
Location: Paris, France
|
| Posted: Wed Jun 14, 2006 8:13 am Post subject: |
|
|
| jeanfrancis wrote: | | That's a Mini-PCI card, do you think I need the PCMCIA things working? |
No. MiniPCI is the same as PCI (just smaller size), so no link with PCMCIA. |
|
| Back to top |
|
|
OpelBlitz
Apprentice
Joined: 12 Dec 2002
Posts: 229
Location: Chicago, Illinois
|
| Posted: Wed Jun 14, 2006 10:32 pm Post subject: |
|
|
| widan wrote: | | jeanfrancis wrote: | | That's a Mini-PCI card, do you think I need the PCMCIA things working? |
No. MiniPCI is the same as PCI (just smaller size), so no link with PCMCIA. |
I know in the Latitude C400, the Dell TrueMobile 1150 is not a true MiniPCI card -- it operates as a PCMCIA/CardBus bridge. |
|
| Back to top |
|
|
tesaklebestift
n00b
Joined: 17 Apr 2006
Posts: 7
|
| Posted: Fri Jun 16, 2006 7:55 am Post subject: |
|
|
I think OpelBlitz is right. It seems that the MiniPCI Slot is not a real PCI-Slot.
After a discussion with several people and many kernel-trys we come to this solution.
I think it is a good way (perhabs not the optimal, but working) to include all drivers in the kernel which are realated to your card. My configuration is for an Orinocco Card. Perhabs you have to include a few more modules in the kernel (try and error).
If this doesn't work try to include all drivers and then the system should recognize your card. If not......ok, then you have a problem. But I don't think that this will happen.
After recognizing your card, remove more and more drivers (why load more code if not necessary).
I don't inlcude any module with modprobe. |
|
| Back to top |
|
|
jeanfrancis
Veteran
Joined: 17 Dec 2005
Posts: 1482
Location: Québec, Canada
|
| Posted: Sat Jun 17, 2006 12:32 am Post subject: |
|
|
Hi !
I finally got it to work. Believe me or not, after LOT of time and tests, I found that I had to add the PCMCIA support for the Orinoco card. (it appeared after I checked the oricono driver, on another section).
So, I unmerged all what I emerged for PCMCIA modules, orinoco drivers, etc. 
Windoz said mi that was a MiniPCI card, but it seems that is not one 
Regards! |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
