| View previous topic :: View next topic |
| Author |
Message |
flimmerfix
n00b
Joined: 11 Jul 2002
Posts: 47
|
 Posted: Thu Apr 10, 2003 3:33 pm Post subject: cdrdao und USB CDRW |
 |
|
Mit cdrdao gelingt es mir nicht eine CD mit meinem USB-Brenner (normaler ATAPI-Brenner im USB2-Gehäuse) zu brennen.
Ich erhalte folgende Fehlermeldung:
| Code: |
Using libscg version 'andreas-0.5-UNIXWARE_Patch'
1,0,0: LITE-ON LTR-12102B Rev: NS1I
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0000)
WARNING: Length of toc (62:26:30, 280980 blocks) exceeds capacity of CD-R (00:00:00, 0 blocks).
WARNING: Ignored because of option '--overburn'.
WARNING: Some drives may fail to record this toc.
?: Input/output error. : scsi sendcmd: no error
CDB: BB 00 FF FF 08 4C 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 20s
ERROR: Cannot set cd speed.
ERROR: Writing speed 12 not supported by device.
|
Auch bei speed 1 erhalte ich die entsprechende Fehlermeldung.
Mit cdrecord kann ich problemlos brennen.
Außerdem wird mein Brenner nicht mehr von k3b erkannt, aber
cdrecord -scanbus und Arson finden ihn.
Ich hoffe mir kann jemand helfen. |
|
| Back to top |
|
 |
flimmerfix
n00b
Joined: 11 Jul 2002
Posts: 47
|
| Posted: Fri Apr 11, 2003 12:09 pm Post subject: |
|
|
Noch als Ergänzung. Wenn ich die Optioen --speed ganz weglasse erhalte ich eine andere Fehlermeldung.
| Code: |
Cdrdao version 1.1.7 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'andreas-0.5-UNIXWARE_Patch'
1,0,0: LITE-ON LTR-12102B Rev: NS1I
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0000)
WARNING: Length of toc (62:26:30, 280980 blocks) exceeds capacity of CD-R (00:00:00, 0 blocks).
WARNING: Ignored because of option '--overburn'.
WARNING: Some drives may fail to record this toc.
Starting write simulation ?: Input/output error. : scsi sendcmd: cmd timeout after 5.999 (20) s
CDB: 5A 00 2A 00 00 00 00 00 8C 00
cmd finished after 5.999s timeout 20s
ERROR: Cannot retrieve drive capabilities mode page.
at speed 0...
Pausing 10 seconds - hit CTRL-C to abort.
Process can be aborted with QUIT signal (usually CTRL-\).
?: Input/output error. : scsi sendcmd: no error
CDB: 1E 00 00 00 01 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 20s
ERROR: Cannot prevent/allow medium removal. |
Woran kann das liegen, USB Geräte werden doch auch wie SCSI Geräte behandelt. Als ich den Brenner noch am IDE Port hatte, hat cdrdao noch funktioniert. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Deutsches Forum (German)
