| View previous topic :: View next topic |
| Author |
Message |
sidious
Tux's lil' helper
Joined: 18 Apr 2006
Posts: 84
Location: Germany
|
 Posted: Thu Jul 06, 2006 4:54 pm Post subject: [solved] Texas Instruments PCIxx21/x515 Cardbus Controller |
 |
|
hi,
I've downloaded and installed kernel 2.6.17.2 from kernel.org,
because there is a new modul for the internal Card-Reader (Texas Instruments PCIxx21/x515 Cardbus Controller)
of my laptop (Acer Extensa 3001 WLMi). The module name is "sdhci"
lspci:
| Code: | 00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to AGP Controller (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
02:02.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
02:04.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
02:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
02:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller
02:06.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller |
the last 3 ones are the controller.
I compiled the fakephp driver as module and loaded it, then I followed this howto:
http://gentoo-wiki.com/HARDWARE_Gentoo_Acer_Ferrari_4005WLMi_Manual#SDHCI
I executet the lines from the sdhci.sh script | Code: | #!/bin/bash
modprobe fakephp
setpci -s 06:09.0 86.b=90:d0 # SDHCI enable
echo 0 > /sys/bus/pci/slots/0000:06:09.3/power
echo 0 > /sys/bus/pci/slots/0000:06:09.2/power
echo 0 > /sys/bus/pci/slots/0000:06:09.0/power
echo 1 > /sys/bus/pci/slots/0000:06:09.0/power
setpci -s 06:09.3 4c.b=02 # FlashMedia SD disable
setpci -s 06:09.4 04.b=06 # SDHCI Mem+ BusMaster+
setpci -s 06:09.4 88.b=01 # SDHCI DMA enable |
one by one with my PCI IDs
| Code: | modprobe fakephp
setpci -s 02:06.0 86.b=90:d0 # SDHCI enable
echo 0 > /sys/bus/pci/slots/0000:02:06.3/power
echo 0 > /sys/bus/pci/slots/0000:02:06.2/power
echo 0 > /sys/bus/pci/slots/0000:02:06.0/power |
the last line gives an error: | Code: | acer ~ # echo 0 > /sys/bus/pci/slots/0000:02:06.0/power
bash: echo: write error: No such device |
but the file | Code: | | /sys/bus/pci/slots/0000:02:06.0/power |
exists
this is the output of dmesg | Code: | pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
fakephp: Can't remove PCI devices with other PCI devices behind it yet. |
If I run the complete script I get two errors | Code: | ./sdhci.sh: line 7: echo: write error: No such device
./sdhci.sh: line 8: echo: write error: No such device
|
that are this lines of the script | Code: | echo 0 > /sys/bus/pci/slots/0000:02:06.0/power
echo 1 > /sys/bus/pci/slots/0000:02:06.0/power |
and dmesg: | Code: | pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
fakephp: Can't remove PCI devices with other PCI devices behind it yet.
sdhci: Secure Digital Host Controller Interface driver, 0.11
sdhci: Copyright(c) Pierre Ossman
PCI: Device 0000:02:06.4 not available because of resource collisions
sdhci: probe of 0000:02:06.4 failed with error -22
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:06.2[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[d020a000-d020a7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f000041ab29]
|
lspci shows a new device | Code: | | 02:06.4 Class 0805: Texas Instruments PCI6411, PCI6421, PCI6611, PCI6621, PCI7411, PCI7421, PCI7611, PCI7621 Secure Digital (SD) Controller |
but I can't use it..... (PCI: Device 0000:02:06.4 not available because of resource collisions). I think it's because the two lines from the script don't work...
any ideas what I can do to get the (SD)-Card-Reader working?
this is my thread in a german gentoo forum...
http://www.gentooforum.de/thread.php?threadid=10675
_________________
AcerExtensa3001WLMi
Last edited by sidious on Mon Sep 11, 2006 5:11 am; edited 1 time in total |
|
| Back to top |
|
 |
bandreabis
Advocate
Joined: 18 Feb 2005
Posts: 2495
Location: イタリアのロディで
|
| Posted: Sat Jul 08, 2006 4:54 pm Post subject: |
|
|
How to compile fakephp?
Andrea
_________________
Il numero di post non fa di me un esperto! Anzi! |
|
| Back to top |
|
|
sidious
Tux's lil' helper
Joined: 18 Apr 2006
Posts: 84
Location: Germany
|
| Posted: Sat Jul 08, 2006 10:17 pm Post subject: |
|
|
select the Fake PCI Hotplug Driver in the kernel-config
| Code: | Bus Options (PCI, PCMCIA, EISA, MCA, ISA) -->
PCI Hotplug Support -->
<M> Support for PCI Hotplug (EXPERIMENTAL)
<M> Fake PCI Hotplug Driver |
_________________
AcerExtensa3001WLMi |
|
| Back to top |
|
|
bandreabis
Advocate
Joined: 18 Feb 2005
Posts: 2495
Location: イタリアのロディで
|
| Posted: Sat Jul 08, 2006 10:55 pm Post subject: |
|
|
I was asking about "diff -u" of fakephp.c ... but it doesn't matter because it was enough putting
| Code: | setpci -s 06:09.0 86.b=90:d0 # SDHCI enable
setpci -s 06:09.3 4c.b=02 # FlashMedia SD disable
setpci -s 06:09.4 04.b=06 # SDHCI Mem+ BusMaster+
setpci -s 06:09.4 88.b=01 # SDHCI DMA enable |
into /etc/conf.d/local.start
(I built-in kernel (original  )"Fake PCI Hotplug Driver")
and magically SD card was recognized! 
now ivman mounts it automatically only after manually setting a mountpoint in fstab (pmount does't do its job  ).
I only can say: | Quote: | | THANK YOU VERY MUCH!!! |
Andrea
_________________
Il numero di post non fa di me un esperto! Anzi!
Last edited by bandreabis on Sun Jul 09, 2006 8:05 am; edited 1 time in total |
|
| Back to top |
|
|
sidious
Tux's lil' helper
Joined: 18 Apr 2006
Posts: 84
Location: Germany
|
| Posted: Sun Jul 09, 2006 7:04 am Post subject: |
|
|
I think in newer kernels like 2.6.17.2 it's not neccessary to patch the fakephp.c file...
hmm, my Card-Reader won't work 
I tried to use a "clean" kernel, means without any patches and the originally DSDT.
(I need a patch and a modified DSDT to read out the smart-battery)
But with the same result..
here are the PCI relevant outputs of dmesg (with the patched kernel and DSDT) | Code: |
dmesg | grep PCI
Allocating PCI resources starting at 30000000 (gap: 20000000:dec10000)
PCI: PCI BIOS revision 2.10 entry at 0xfd782, last bus=2
Setting up standard PCI resources
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *6)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *6)
ACPI: PCI Interrupt Link [LNKD] (IRQs *6)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10)
ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 6) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
PCI: Bus 3, cardbus bridge: 0000:02:06.0
PCI: Bridge: 0000:00:1e.0
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:06.0 (0104 -> 0107)
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6
PCI: setting IRQ 6 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
GLAN MPCI T394 MDM0 USB1 USB2 USB3
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ mask 0x08b8, PCI irq 10
pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd05fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x32ffffff
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1d.0 to 64
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1d.1 to 64
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6
PCI: Setting latency timer of device 0000:00:1d.2 to 64
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
fakephp: Can't remove PCI devices with other PCI devices behind it yet.
fakephp: Can't remove PCI devices with other PCI devices behind it yet.
PCI: Device 0000:02:06.4 not available because of resource collisions
ACPI: PCI Interrupt 0000:02:06.2[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[d020a000-d020a7ff] Max Packet=[2048] IR/IT ontexts=[4/8]
|
and the dmesg outputs which contain the PCI-IDs 02:06.x | Code: | PCI: Bus 3, cardbus bridge: 0000:02:06.0
PCI: Enabling device 0000:02:06.0 (0104 -> 0107)
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:06.0 [1025:0064]
Yenta TI: socket 0000:02:06.0, mfunc 0x01a21b22, devctl 0x64
PCI: Device 0000:02:06.4 not available because of resource collisions
sdhci: probe of 0000:02:06.4 failed with error -22 |
I tried to add
to the kernel options in /boot/grub/grub.conf ,but it still wont' work. 
just putting | Code: | setpci -s 02:06.0 86.b=90:d0 # SDHCI enable
setpci -s 02:06.3 4c.b=02 # FlashMedia SD disable
setpci -s 02:06.4 04.b=06 # SDHCI Mem+ BusMaster+
setpci -s 02:06.4 88.b=01 # SDHCI DMA enable |
into /etc/conf.d/local.start doesn't work, too.
Someone out there who can help me?
_________________
AcerExtensa3001WLMi |
|
| Back to top |
|
|
sidious
Tux's lil' helper
Joined: 18 Apr 2006
Posts: 84
Location: Germany
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
