| View previous topic :: View next topic |
| Author |
Message |
bifi
n00b
Joined: 03 Aug 2006
Posts: 5
|
 Posted: Thu Aug 03, 2006 3:17 pm Post subject: Problems connecting to Wlan Router |
 |
|
hi.
as mentioned above my problem is that somehow I got no connection to my Router and the Internet.
I got Gentoo running a 2.6.17-r4 Kernel. I experienced many problems till my Wlan Card inside my Laptop was running.
My Card is a Broadcom BCM4306 802.11b/g Ethernet Card.
First I tried to to emulate with ndiswrapper, but found that a lot of programs got problems with this method. I played around with bcm43xx-fwcutter, read a few Tutorials, recompiled the kernel 10-15x
...and now it seems to work. I emerged wireless-tools and if I type iwconfig my card is in the output
| Code: | iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
dummy0 no wireless extensions.
eth1 IEEE 802.11b/g ESSID:"Drivecard" Nickname:"Drivecard"
Mode:Ad-Hoc Frequency=2.484 GHz Cell: Invalid
Bit Rate=11 Mb/s Tx-Power=15 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
|
So I setted up my Router (with no encryption) and gave it an SSID "Fritz". Then I setted up my wlan card with a
| Code: | | iwconfig eth1 mode managed essid Fritz |
Dmesg says that I am now authenticated and associated, but somehow I can`t get a ping to the router on some web sites. What could be the problem?
While booting up there are some strange things I can´t understand. So I am posting my dmesg report, too.
| Code: | dmesg
Linux version 2.6.17-gentoo-r4 (root@localhost) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #10 SMP PREEMPT Sun Jul 30 21:00:10 GMT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fec9000 (usable)
BIOS-e820: 000000003fec9000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000fdf00
ACPI: RSDT (v001 DELL CPi R 0x27d50605 ASL 0x00000061) @ 0x3fef0000
ACPI: FADT (v001 DELL CPi R 0x27d50605 ASL 0x00000061) @ 0x3fef0400
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 50000000 (gap: 40000000:bec10000)
Built 1 zonelists
Kernel command line: root=/dev/hdc3
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0170d000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2398.353 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 904308k/917504k available (2900k kernel code, 12764k reserved, 1114k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4801.17 BogoMIPS (lpj=9602343)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 20k freed
ACPI: setting ELCR to 0200 (from 0800)
CPU0: Intel(R) Celeron(R) CPU 2.40GHz stepping 09
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfcfae, last bus=2
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:02: ioport range 0x800-0x805 could not be reserved
pnp: 00:02: ioport range 0x808-0x80f could not be reserved
pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:03: ioport range 0x806-0x807 has been reserved
pnp: 00:03: ioport range 0x810-0x85f could not be reserved
pnp: 00:03: ioport range 0x860-0x87f has been reserved
pnp: 00:03: ioport range 0x880-0x8bf has been reserved
pnp: 00:03: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x900-0x97f has been reserved
pnp: 00:0b: ioport range 0x7b0-0x7bb has been reserved
pnp: 00:0b: ioport range 0x7c0-0x7df has been reserved
pnp: 00:0b: ioport range 0xbb0-0xbbb has been reserved
pnp: 00:0b: ioport range 0xbc0-0xbdf has been reserved
pnp: 00:0b: ioport range 0xfb0-0xfbb has been reserved
pnp: 00:0b: ioport range 0xfc0-0xfdf has been reserved
pnp: 00:0b: ioport range 0x13b0-0x13bb has been reserved
pnp: 00:0b: ioport range 0x13c0-0x13df has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 0000d000-0000d0ff
IO window: 0000d400-0000d4ff
PREFETCH window: 50000000-51ffffff
MEM window: f8000000-f9ffffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-efff
MEM window: f8000000-fdffffff
PREFETCH window: 50000000-52ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:04.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1154620779.124:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/W].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
lp: driver loaded but no devices found
i8k: unable to get SMM BIOS version
Dell laptop SMM driver v1.14 21/02/2005 Massimo Dal Zotto (dz@debian.org)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
[drm] Initialized drm 1.0.1 20051102
vesafb: Intel Corporation, Intel(r)852GM/852GME/855GM/855GME Graphics Controller, Hardware Version 0.0 (OEM: Intel(r)852GM/852GME/855GM/855GME Graphics Chip Accelerated VGA BIOS)
vesafb: VBE version: 3.0
vesafb: VBIOS/hardware supports DDC2 transfers
vesafb: monitor limits: vf = 60 Hz, hf = 48 kHz, clk = 65 MHz
vesafb: using default BIOS refresh rate
vesafb: scrolling: redraw
vesafb: framebuffer at 0xe8000000, mapped to 0xf8980000, using 832k, total 832k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (50 C)
ibm_acpi: ec object not found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Warning: Keylock active.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x256eb1, caps: 0x804713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
floppy0: no floppy controllers found
b44.c:v1.00 (Apr 7, 2006)
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0f:1f:1b:c5:0c
bcm43xx driver
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
bcm43xx: Chip ID 0x4306, rev 0x2
bcm43xx: Number of cores: 6
bcm43xx: Core 0: ID 0x800, rev 0x2, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x4, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x80d, rev 0x1, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x807, rev 0x1, vendor 0x4243, disabled
bcm43xx: Core 4: ID 0x804, rev 0x7, vendor 0x4243, enabled
bcm43xx: Core 5: ID 0x812, rev 0x4, vendor 0x4243, disabled
bcm43xx: Ignoring additional 802.11 core.
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 1, Type 2, Revision 1
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SONY CD-RW/DVD-ROM CRX830E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: FUJITSU MHT2030AT, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 128KiB
hdc: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2 hdc3
hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29, 2006)
libata version 1.20 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf6effc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver cytherm
drivers/usb/misc/cytherm.c: v1.0:Cypress USB Thermometer driver
usbcore: registered new driver phidgetservo
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-2)
Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC).
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55321 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel 82801DB-ICH4 with STAC9750,51 at 0xf6eff800, irq 7
oprofile: using timer interrupt.
pktgen v2.67: Packet Generator for packet performance testing.
ip_conntrack version 2.4 (7168 buckets, 57344 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
Using IPI Shortcut mode
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
(fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status 0, recovered transactions 22547 to 22634
(fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 4603 and revoked 585/535 blocks
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 204k freed
Adding 1959920k swap on /dev/hdc2. Priority:-1 extents:1 across:1959920k
EXT3 FS on hdc3, internal journal
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: disagrees about version of symbol ieee80211_get_crypto_ops
ieee80211: Unknown symbol ieee80211_get_crypto_ops
ieee80211: disagrees about version of symbol ieee80211_crypt_deinit_entries
ieee80211: Unknown symbol ieee80211_crypt_deinit_entries
ieee80211: disagrees about version of symbol ieee80211_crypt_delayed_deinit
ieee80211: Unknown symbol ieee80211_crypt_delayed_deinit
ieee80211: disagrees about version of symbol ieee80211_crypt_quiescing
ieee80211: Unknown symbol ieee80211_crypt_quiescing
ieee80211softmac: no version for "ieee80211_wx_get_scan" found: kernel tainted.
ieee80211softmac: exports duplicate symbol alloc_ieee80211softmac (owned by kernel)
bcm43xx: PHY connected
bcm43xx: PHY disconnected
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1130
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1132
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1132
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1132
bcm43xx: TODO: Incomplete code in keymac_write() at drivers/net/wireless/bcm43xx/bcm43xx_main.c:1132
bcm43xx: Keys cleared
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: set security called
bcm43xx: .level = 0
bcm43xx: .enabled = 0
bcm43xx: .encrypt = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
bcm43xx: set security called
bcm43xx: .level = 0
bcm43xx: .enabled = 0
bcm43xx: .encrypt = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
bcm43xx: set security called
bcm43xx: .level = 0
bcm43xx: .enabled = 0
bcm43xx: .encrypt = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
device eth1 entered promiscuous mode
audit(1154621340.614:2): dev=eth1 prom=256 old_prom=0 auid=4294967295
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:01:e3:4a:91:fd
SoftMAC: cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:01:e3:4a:91:fd.
SoftMAC: Open Authentication completed with 00:01:e3:4a:91:fd
SoftMAC: sent association request!
SoftMAC: associated!
|
Hope somebody can help me!
Last edited by bifi on Thu Aug 03, 2006 4:42 pm; edited 1 time in total |
|
| Back to top |
|
 |
aqu
Apprentice
Joined: 12 Nov 2005
Posts: 249
Location: Kalisz, Poland
|
| Posted: Thu Aug 03, 2006 3:28 pm Post subject: |
|
|
you have to set ip for your laptop by dhcp or manualy
_________________
Security is like Ogres and Onions, they have layers.
Linux - Registered user #415939
adopt an unanswered post |
|
| Back to top |
|
|
bifi
n00b
Joined: 03 Aug 2006
Posts: 5
|
| Posted: Thu Aug 03, 2006 4:17 pm Post subject: |
|
|
I setted it up manually
| Code: | ifconfig
eth0 Link encap:Ethernet HWaddr 00:0F:1F:1B:C5:0C
inet addr:192.168.1.3 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4839 errors:0 dropped:0 overruns:0 frame:0
TX packets:526 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:360553 (352.1 Kb) TX bytes:74638 (72.8 Kb)
Interrupt:7
eth1 Link encap:Ethernet HWaddr 00:90:4B:72:C2:CD
inet addr:192.168.1.4 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:128 overruns:0 frame:0
TX packets:250 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:11288 (11.0 Kb)
Interrupt:11
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
|
eth1 is my WLAN NIC |
|
| Back to top |
|
|
aqu
Apprentice
Joined: 12 Nov 2005
Posts: 249
Location: Kalisz, Poland
|
| Posted: Thu Aug 03, 2006 5:51 pm Post subject: |
|
|
try to search for wireless networks
| Code: | | iwlist eth1 scanning |
couse your router can even dont sent any signal
_________________
Security is like Ogres and Onions, they have layers.
Linux - Registered user #415939
adopt an unanswered post |
|
| Back to top |
|
|
bifi
n00b
Joined: 03 Aug 2006
Posts: 5
|
| Posted: Fri Aug 04, 2006 12:47 pm Post subject: |
|
|
hi thx for your answers...but the problem was so stupid... I linked my net.eth1 (wlan) to net.eth0 instead of net.lo
That was the cause....so threat can be closed! |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
