| View previous topic :: View next topic |
| Author |
Message |
ap3s
n00b
Joined: 02 May 2006
Posts: 5
|
 Posted: Sat Aug 05, 2006 10:29 pm Post subject: [SOLVED] eth0 does not exist |
 |
|
Witam. Mam pewien problem. (kto ich nie ma??)
Od kilku dni mecze sie na gentoo z instalacja karty sieciowej. Ciagle przy starcie mam komunikat:
| Code: | eth0 does not exist
ERROR: Problem starting needed ervices.
"netmount" was not started |
Moja sieciowka to
| Code: | lspci
0000:02:05.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] (rev 12) |
W moim kernelu 2.6.17-r4 (gentoo source) nie mam dokladnie tego sterownika wiec zaznaczalem inne(podobne) ale efektu brak.
ifconfig daje wynik tylko z lo
/etc/init.d/net.eth0 start/restart rowniez daje wynik negatywny.
polecenia ping daja efekt nieznany host itp.
jeszcze, jezeli wpisze pod gentoo lspci to karte wyswietla poprawnie.
lacze sie przez router adsl (DNS ustawione)
w livecd internet chodzi bez problemów.
Bede wdzieczny za podpowiedz.
Last edited by ap3s on Sun Aug 06, 2006 10:35 am; edited 1 time in total |
|
| Back to top |
|
 |
Raku
Bodhisattva
Joined: 28 Feb 2004
Posts: 2374
Location: Poland
|
| Posted: Sat Aug 05, 2006 10:39 pm Post subject: Re: eth0 does not exist |
|
|
| ap3s wrote: | w livecd internet chodzi bez problemów.
Bede wdzieczny za podpowiedz. |
podpowiedź została pogrubiona.
Druga: zobacz, jakie moduły ładuje livecd.
_________________
raku
Powered by Archlinux  |
|
| Back to top |
|
|
ap3s
n00b
Joined: 02 May 2006
Posts: 5
|
| Posted: Sun Aug 06, 2006 8:14 am Post subject: |
|
|
To sa moduły z liveCD
| Code: | Module Size Used by
ipv6 187744 8
hci_usb 10804 0
bluetooth 30948 1 hci_usb
parport_pc 26948 0
parport 21544 1 parport_pc
floppy 46244 0
pcspkr 1156 0
rtc 8948 0
sk98lin 127008 0
dm_mirror 14672 0
dm_mod 37048 1 dm_mirror
pdc_adma 6212 0
sata_mv 12516 0
ata_piix 6532 0
ahci 9124 0
sata_qstor 6468 0
sata_vsc 5316 0
sata_uli 4644 0
sata_sis 5220 0
sata_sx4 10052 0
sata_nv 5924 0
sata_via 5668 0
sata_svw 4932 0
sata_sil24 7684 0
sata_sil 6244 0
sata_promise 7716 0
libata 35912 15 pdc_adma,sata_mv,ata_piix,ahci,sata_qstor,sata_vsc,sata_uli,sata_sis,sata_sx4,sata_nv,sata_via,sata_svw,sata_sil24,sata_sil,sata_promise
sbp2 16484 0
ohci1394 25140 0
ieee1394 57272 2 sbp2,ohci1394
sl811_hcd 9344 0
ohci_hcd 14916 0
uhci_hcd 24144 0
usb_storage 49920 0
usbhid 28992 0
ehci_hcd 22856 0
usbcore 80068 8 hci_usb,sl811_hcd,ohci_hcd,uhci_hcd,usb_storage,usbhid,ehci_hcd |
ipv6 mam ktore jeszcze musze miec w systemie?? |
|
| Back to top |
|
|
Jabolem
n00b
Joined: 02 Aug 2006
Posts: 30
|
|
| Back to top |
|
|
Yatmai
Veteran
Joined: 12 Nov 2005
Posts: 1501
Location: Kraków
|
| Posted: Sun Aug 06, 2006 10:29 am Post subject: |
|
|
To samo co mnie tłukli: "czytaj opisy modułów i dokumentacje kernela"  To naprawde nie szkodzi 
| Code: | CONFIG_SK98LIN:
│
│ Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
│ compliant Gigabit Ethernet Adapter.
│
│ This driver supports the original Yukon chipset. A cleaner driver is
│ also available (skge) which seems to work better than this one.
│
│ This driver does not support the newer Yukon2 chipset. A seperate
│ driver, sky2, is provided to support Yukon2-based adapters.
│
│ The following adapters are supported by this driver:
│ - 3Com 3C940 Gigabit LOM Ethernet Adapter |
_________________
Desktop: [Ath64 X2 2GB DDR2 GF76GT] [amd64] [2.6.29-gentoo] [nVidia] [KDE 3.5.10]
Lapek: [HP nc6000] [i686] [2.6.29-ARCH] [ati-open] [KDE 3.5.10] |
|
| Back to top |
|
|
ap3s
n00b
Joined: 02 May 2006
Posts: 5
|
| Posted: Sun Aug 06, 2006 10:34 am Post subject: |
|
|
Dzieki wszystkim za pomoc. W szczególnosci Jabolem'u 
Chyba dam solved
arsen edit: nie solvet a solved, zmienione jak i w tym poście jak i w tytule wątka. |
|
| Back to top |
|
|
|
Polskie forum (Polish)
