| View previous topic :: View next topic |
| Author |
Message |
maximum_one
n00b
Joined: 12 Oct 2004
Posts: 59
|
 Posted: Sun Jul 23, 2006 3:32 pm Post subject: udev Problem |
 |
|
Hallo,
nachdem ich ursprünglich ein Problem mit ALSA hatte habe ich mal udev emerged
und siehe da ALSA tut wieder seinen Dienst .
ABER :
Ich bekomme nun seltsame Fehlermeldungen, die ich nicht zu deuten weiß.
Vielleicht kann mir ja jemand weiterhelfen :
Output von dmesg :
Hierbei machen mir diese Status-Errors BadCRC Sorgen.
Die gleichen Fehlermeldungen erhalte ich auch beim weiteren Bootvorgang.
Das Booten selbst funktioniert aber.
| Code: |
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y120L0, ATA DISK drive
hdb: Pioneer DVD-ROM ATAPIModel DVD-105S 013, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA CD/DVDW SD-R5372, ATAPI CD/DVD-ROM drive
hdd: IC35L120AVVA07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hda: cache flushes supported
hda:hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: DMA disabled
ide0: reset: success
hda1 hda2 < hda5 hda6 >
hdd: max request size: 128KiB
hdd: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hdd: cache flushes supported
hdd: hdd1 hdd2 hdd3 hdd4 < hdd5 hdd6 >
hdb: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
|
Muss ich mir wegen dem dmesg-Output um meine Festplatte sorgen machen ?
Beim Booten bekomme ich ebenso die obrigen Fehler und zusätzlich folgendes :
| Code: |
uded-event[1961] find_free_number : %e is depricated, will be removed and is unlikely to work correctly. Don't use it.
|
Beim Herunterfahren erhalte ich folgende Fehler :
| Code: |
udevd[1859] : delete_path : rmdir (./dev/.udev) failed : read-only file system
udevd-event[11983] : udev_make_mode (/dev/bus/usb/002/002, 829644, 189, 12) failed. Read-only file system
|
Vielleicht kann mir ja jemand helfen.
Danke |
|
| Back to top |
|
 |
think4urs11
Bodhisattva
Joined: 25 Jun 2003
Posts: 6659
Location: above the cloud
|
| Posted: Sun Jul 23, 2006 4:03 pm Post subject: |
|
|
Die CRC-Fehler könn(t)en daher kommen das mehrere (2) Geräte am gleichen IDE-Kabel hängen oder aber von einem defekten Kabel.
Die 'depricated'-Meldung ist kein Grund zur Sorge, das ist eher für Entwickler gedacht; https://forums.gentoo.org/viewtopic-t-455712.html
Die udev-Fehler sehen nach folgenden Bugs aus: https://bugs.gentoo.org/show_bug.cgi?id=121449; https://bugs.gentoo.org/show_bug.cgi?id=126889
Welche udev-Version setzt du ein?
Wie sehen deine hdparm-Einstellungen aus (hdparm-iI /dev/hdx)
_________________
Nothing is secure / Security is always a trade-off with usability / Do not assume anything / Trust no-one, nothing / Paranoia is your friend / Think for yourself |
|
| Back to top |
|
|
maximum_one
n00b
Joined: 12 Oct 2004
Posts: 59
|
| Posted: Sun Jul 23, 2006 4:20 pm Post subject: |
|
|
Die Version von udev ist : 087-r1
Ausgabe von hdparm :
hda (Festplatte)
| Code: |
/dev/hda:
Model=Maxtor 6Y120L0, FwRev=YAR41BW0, SerialNo=Y31HWCRE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=240121728
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7
* signifies the current active mode
ATA device, with non-removable media
Model Number: Maxtor 6Y120L0
Serial Number: Y31HWCRE
Firmware Revision: YAR41BW0
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 4047
heads 16 16
sectors/track 63 255
--
CHS current addressable sectors: 16511760
LBA user addressable sectors: 240121728
device size with M = 1024*1024: 117246 MBytes
device size with M = 1000*1000: 122942 MBytes (122 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
|
hdb (DVD-Laufwerk)
| Code: |
/dev/hdb:
Model=Pioneer DVD-ROM ATAPIModel DVD-105S 013, FwRev=E1.33, SerialNo=
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=13395, BuffSize=64kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no
Drive conforms to: Unspecified: ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4
* signifies the current active mode
ATAPI CD-ROM, with removable media
Model Number: Pioneer DVD-ROM ATAPIModel DVD-105S 0133
Serial Number:
Firmware Revision: E1.33
Standards:
Likely used CD-ROM ATAPI-1
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 64.0kB
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* DEVICE RESET cmd
* PACKET command feature set
* Power Management feature set
|
hdc (DVD/CD-Writer)
| Code: |
/dev/hdc:
Model=TOSHIBA CD/DVDW SD-R5372, FwRev=TU53, SerialNo=154F500295
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=2048kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no
Drive conforms to: Reserved: ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7
* signifies the current active mode
ATAPI CD-ROM, with removable media
Model Number: TOSHIBA CD/DVDW SD-R5372
Serial Number: 154F500295
Firmware Revision: TU53
Standards:
Used: ATAPI for CD-ROMs, SFF-8020i, r2.5
Supported: CD-ROM ATAPI-2
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 2048.0kB
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* DEVICE RESET cmd
* PACKET command feature set
* Power Management feature set
* Mandatory FLUSH CACHE command
HW reset results:
CBLID- above Vih
Device num = 0
|
hdd (Festplatte)
| Code: |
/dev/hdd:
Model=IC35L120AVVA07-0, FwRev=VA6OA52A, SerialNo=VNC602A6C5D2GA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=241254720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5
* signifies the current active mode
ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.
Model Number: IC35L120AVVA07-0
Serial Number: VNC602A6C5D2GA
Firmware Revision: VA6OA52A
Standards:
Used: ATA/ATAPI-5 T13 1321D revision 1
Supported: 5 4 3 2 & some of 6
Configuration:
Logical max current
cylinders 16383 4047
heads 16 16
sectors/track 63 255
--
CHS current addressable sectors: 16511760
LBA user addressable sectors: 241254720
device size with M = 1024*1024: 117800 MBytes
device size with M = 1000*1000: 123522 MBytes (123 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 52 Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
Release interrupt
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
SMART feature set
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
Automatic Acoustic Management feature set
SET MAX security extension
Address Offset Reserved Area Boot
SET FEATURES subcommand required to spinup after power up
Power-Up In Standby feature set
Advanced Power Management feature set
* READ/WRITE DMA QUEUED
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 1 determined by the jumper
Checksum: correct
|
Ich weiß nicht ob es was zu bedeuten hat, aber hier sieht es so aus als wären die checksummen ok oder ? |
|
| Back to top |
|
|
Cheffdau
n00b
Joined: 04 Oct 2004
Posts: 39
Location: Nürnberg
|
| Posted: Fri Aug 18, 2006 8:49 am Post subject: |
|
|
Selbes Problem bei mir auf AMD64.
Hatte ja gehofft das hier ne Lösung kommt da die Hinweise aus den englischen Foren nicht weiterhalfen.
Problem ist immernoch beim stoppen des Systems aktuell.
Deshalb mal das Posting zurück nach oben.
Gruß
Charly
_________________
Was ich nicht weis, füllt ganze Bibliotheken ... |
|
| Back to top |
|
|
toskala
Advocate
Joined: 14 Dec 2002
Posts: 2080
Location: hamburg, germany
|
| Posted: Sat Aug 19, 2006 8:30 pm Post subject: |
|
|
kommen die fehler auch wenn du ein knoppix bootest?
DriveReady SeekComplete Error kann halt so ziemlich alles bedeuten...
_________________
adopt an unanswered post
erst denken, dann posten |
|
| Back to top |
|
|
Cheffdau
n00b
Joined: 04 Oct 2004
Posts: 39
Location: Nürnberg
|
| Posted: Sun Aug 20, 2006 12:19 pm Post subject: |
|
|
Hi,
nein.
Der fehler kommt nur beim auf HD installierten Gentoo.
CD-Versionen, getestet hab ich Knoppix, kanotix, kanotix 64, stoppen ohne Probleme.
Im Betrieb merkt man nichts, nur beim stoppen.
In den englischen Gruppen fand ich eine Bemerkung das sich die User mit dem Power Button behelfen. Ich mach das derzeit auch so. Anscheinend gibts ein Problem im treiber.
Gruss
Charly
_________________
Was ich nicht weis, füllt ganze Bibliotheken ... |
|
| Back to top |
|
|
toskala
Advocate
Joined: 14 Dec 2002
Posts: 2080
Location: hamburg, germany
|
| Posted: Sun Aug 20, 2006 4:14 pm Post subject: |
|
|
versuch mal einen anderen kernel, ich hatte das mal eine zeitlang mit ide geräten auf einem intel serverworks chipsatz. ein paar kernel versionen später wars dann auf einmal weg.
_________________
adopt an unanswered post
erst denken, dann posten |
|
| Back to top |
|
|
Cheffdau
n00b
Joined: 04 Oct 2004
Posts: 39
Location: Nürnberg
|
| Posted: Mon Aug 21, 2006 1:49 pm Post subject: |
|
|
Moinmoin,
neuer Kernel geht nicht da ich den letzten Stand hab. Was mich wundert st das der Kernel ja mal lief. Ich weis nur dummerweise nicht was beim letzten Update das Problem in das System gebracht hat.
Naja, schaung mer mal dann sehng mer scho ...
Charly
_________________
Was ich nicht weis, füllt ganze Bibliotheken ... |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Deutsches Forum (German)
