ltmodem "NO CARRIER"

[grajagan]

I have installed gentoo 2006.1 and tried to use my Lucent WinModem... I did "emerge ltmodem" (8.31_alpha10-r2, but it also used the ltmodem-2.6-alk-8 version to install the driver) and it work's fine... But, when I try to dialout with wvdial I get this error (and no noise from modem):

hawking ~ # wvdial
--> WvDial: Internet dialer version 1.56
--> Initializing modem.
--> Sending: ATX3
ATX3
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT30359994
--> Waiting for carrier.
ATDT30359994
NO CARRIER
--> No Carrier! Trying again.
--> Sending: ATDT30359994
--> Waiting for carrier.
ATDT30359994
NO CARRIER
...


My /etc/wvidal.conf

[Dialer Defaults]
Init3 = ATM1L1
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = 30358300
ISDN = 0
Username = pop
Init1 = ATX3
Password = pop
Modem = /dev/modem
Baud = 57600


And here is the output of 'wvdialconf':

hawking ~ # wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: Scanning ttyLTM0 first, /dev/modem is a link to it.
ttyLTM0<*1>: ATQ0 V1 E1 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 Z -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyLTM0<*1>: Modem Identifier: ATI -- LT V.92 Data+Fax Modem Version 8.30
ttyLTM0<*1>: Speed 4800: AT -- OK
ttyLTM0<*1>: Speed 9600: AT -- OK
ttyLTM0<*1>: Speed 19200: AT -- OK
ttyLTM0<*1>: Speed 38400: AT -- OK
ttyLTM0<*1>: Speed 57600: AT -- OK
ttyLTM0<*1>: Speed 115200: AT -- OK
ttyLTM0<*1>: Max speed is 115200; that should be safe.
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1
ttyS2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS3<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS3<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS3<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.

Found a modem on /dev/ttyLTM0, using link /dev/modem in config.
/etc/wvdial.conf<Warn>: Can't open '/etc/wvdial.conf' for reading: No such file or directory
/etc/wvdial.conf<Warn>: ...starting with blank configuration.
Modem configuration written to /etc/wvdial.conf.
ttyLTM0<Info>: Speed 115200; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"


I'm using kernel 2.6.17-gentoo-r5 (with SMP support already disabled)
Any ideas?